Fixing 7200.10 Seagate ST3160215AS by means of Clear Smart

[mikail13]

Data appears with clear smart F,,11
and R1 , R2 commands

Buzz HM SFI
!
(P)SATA Reset
DiskAccess ReadSector EC=47 at ffffffff.00.0002
DiskAccess ReadSector EC=47 at ffffffff.00.0002

Read Ver Retrys
DiskAccess ReadSector EC=43 at ffffffff.00.0002

Read Ver Retrys
DiskAccess ReadSector EC=43 at ffffffff.00.0002

Read Ver Retrys
DiskAccess ReadSector EC=47 at ffffffff.00.0002

Read Ver Retrys
DiskAccess ReadSector EC=47 at ffffffff.00.0002

Read Ver Failure!
DiskAccess ReadSector EC=47 at ffffffff.00.022b
Failed sys sect. write! Nwt Er 00 RdWr 134e2.00.022b
DiskAccess ReadSector EC=47 at ffffffff.00.0080
DiskAccess ReadSector EC=47 at ffffffff.00.0080
Unable To Load Overlay 01|000A

T>$SFI
$SFI
AMR
$SFI
AMR
$SFI
AMR
T>F,,11

Buzz HM SFI
!
$SFI
AMR
$SFI
$SFI
AMR
$SFI
AMR
$SFI
AMR
$DiskAccess ReadSector EC=11 at ffffffff.00.0000
HM SFI
!
$SFI
$SFI
AMR
$SFI
$SFI
AMR
$SFI
AMR
$DiskAccess ReadSector EC=11 at ffffffff.00.0000
Unable To Load Overlay 00|0016

T>R1

Buzz HM SFI
!
$SFI
AMR
$SFI
$SFI
AMR
$SFI
AMR
$SFI
$SFI
AMR
$SFI
AMR
$SFI
AMR
$ Code - 71 Track FFFFF(134DE).0.000 Sns 000 Rty 027F.FF.80FF Rtf 1800 L
BA 000003E5
T>R2

Buzz HM SFI
$SFI
AMR
$SFI
AMR
$SFI
$SFI
AMR
$SFI


$SFI
AMR
$ Code - 71 Track FFFFF(134DE).0.000 Sns 000 Rty 027F.FF.80FF Rtf 1800 L
BA 000003E9
T>Reset
1024k x 16 DRAM
NHAWK - 1_Disk S-41 10-23-06_16:40

Buzz HM HM HM HM HM HM HM HM SFI
!
(P)SATA Reset
DiskAccess ReadSector EC=47 at ffffffff.00.0002

[mikail13]

yes. drive come back with F,,11 command.

and i actually don't know name of F,,11 command. looks like clear smart . maybe clear smart is N1 on these drive..

drive has many bads on last part.. you can see ..


is anyone know what do F,,11 command?

Attachments

[mikail13]

The hard disk was clicking some at boot before I tried.
only R1 and R2 command was useless but F,,11.

all data succesfully recovered. also.. drive is good. there are many bads after 145 gb. but it's not important.
even if your drive is fully healthy you must not exceed %80.

i have read this.

http://www.msfn.org/board/topic/133604- ... state-too/