All times are UTC - 5 hours [ DST ]




Post new topic Reply to topic  [ 9 posts ] 
Author Message
 Post subject: HItachi HDS721050CLA362 LOGIC BOARD SHORTED
PostPosted: October 17th, 2018, 13:22 
Offline

Joined: October 17th, 2018, 3:40
Posts: 6
Location: india
I accidentally shorted my PC HARD DISK. It accidentally touched a metal surface and burned a capacitor on the logic board.
It is not spinning and also not detecting.
Is it possible to fix the board by replacing the burn capacitor?
I checked the board for any short circuit near the OA56511 IC ( may be a voltage regulator) and the only thing shorted is that the burned capacitor.
It will be very helpful if someone can provide any information and guidance on troubleshooting and fixing the logic board.


Attachments:
IMG_20181016_131003.jpg
IMG_20181016_131003.jpg [ 571.62 KiB | Viewed 7321 times ]
IMG_20181016_131111.jpg
IMG_20181016_131111.jpg [ 481.74 KiB | Viewed 7321 times ]
IMG_20181016_131131.jpg
IMG_20181016_131131.jpg [ 2.12 MiB | Viewed 7321 times ]
Top
 Profile  
 
 Post subject: Re: HItachi HDS721050CLA362 LOGIC BOARD SHORTED
PostPosted: October 17th, 2018, 15:33 
Offline
User avatar

Joined: September 8th, 2009, 18:21
Posts: 15463
Location: Australia
See http://www.hddoracle.com/viewtopic.php?f=59&t=231&p=596#p9159

The OA56511 IC is a spindle motor +VCM + power controller.

If you remove the capacitor, does the short circuit persist?

_________________
A backup a day keeps DR away.


Top
 Profile  
 
 Post subject: Re: HItachi HDS721050CLA362 LOGIC BOARD SHORTED
PostPosted: October 18th, 2018, 1:54 
Offline

Joined: March 11th, 2008, 4:35
Posts: 1050
Location: Bangladesh
Better you buy a new board, let me know if u need 1.

_________________
__________
There is no substitute for education and experience
THANK YOU
SHAHI
shahi.mahbub@gmail.com


Top
 Profile  
 
 Post subject: Re: HItachi HDS721050CLA362 LOGIC BOARD SHORTED
PostPosted: October 18th, 2018, 6:01 
Offline

Joined: October 17th, 2018, 3:40
Posts: 6
Location: india
fzabkar wrote:
See http://www.hddoracle.com/viewtopic.php?f=59&t=231&p=596#p9159

The OA56511 IC is a spindle motor +VCM + power controller.

If you remove the capacitor, does the short circuit persist?

I have not removed the capacitor yet, but it burned on of its solder pads and it is completely isolated from the circuit except the ground connection.


Top
 Profile  
 
 Post subject: Re: HItachi HDS721050CLA362 LOGIC BOARD SHORTED
PostPosted: October 20th, 2018, 6:37 
Offline

Joined: October 17th, 2018, 3:40
Posts: 6
Location: india
I removed the capacitor from PCB and one of the pads are completely burned. I checked the cap and it was shorted, now there is no short in the PCB.
The only thing is that the capacitor(no specification)?


Attachments:
IMG_20181020_154206.jpg
IMG_20181020_154206.jpg [ 2.4 MiB | Viewed 7173 times ]
Top
 Profile  
 
 Post subject: Re: HItachi HDS721050CLA362 LOGIC BOARD SHORTED
PostPosted: October 20th, 2018, 15:39 
Offline
User avatar

Joined: September 8th, 2009, 18:21
Posts: 15463
Location: Australia
@deb95, it would help to determine the function of the shorted capacitor.

To this end I would test the capacitor pads for continuity with ground, +5V and +12V (SATA power), and the Vcc pins of the SDRAM (pin #1) and serial flash memory (25FU206, pin #8).

If there no connection to any of these supply voltages, then the capacitor may the boost capacitor for the VCM circuit.

_________________
A backup a day keeps DR away.


Top
 Profile  
 
 Post subject: Re: HItachi HDS721050CLA362 LOGIC BOARD SHORTED
PostPosted: October 28th, 2018, 2:29 
Offline

Joined: October 17th, 2018, 3:40
Posts: 6
Location: india
@fzabkar
+5V and GND are directly connected to the capacitor.
There are two other pins from the OA56511(do you have any datasheet?), that are directly connected. (see the pictures)
No connection with the flash memory(25FU206) and SDRAM(K4H281638L, Samsung).


Attachments:
SD.JPG
SD.JPG [ 376.74 KiB | Viewed 6820 times ]
DSC00406.JPG
DSC00406.JPG [ 6.31 MiB | Viewed 6820 times ]
DSC00407.JPG
DSC00407.JPG [ 6.25 MiB | Viewed 6820 times ]
Top
 Profile  
 
 Post subject: Re: HItachi HDS721050CLA362 LOGIC BOARD SHORTED
PostPosted: October 28th, 2018, 2:44 
Offline
User avatar

Joined: September 8th, 2009, 18:21
Posts: 15463
Location: Australia
It would appear that the capacitor filters the +5V supply to the motor controller. Those two pins would be the Vcc and ground for the IC. On that basis ISTM that you could make do with a 10uF MLCC or even a low ESR leaded electrolytic capacitor. Just make sure that the chip's pins make contact with the thruholes. In fact, if the traces are still intact, then the PCB may work without any capacitor at all (although you should still replace it).

Best of luck.

I don't have a datasheet, BTW. I believe that these motor controller ICs are custom designs.

_________________
A backup a day keeps DR away.


Top
 Profile  
 
 Post subject: Re: HItachi HDS721050CLA362 LOGIC BOARD SHORTED
PostPosted: October 31st, 2018, 13:44 
Offline

Joined: October 17th, 2018, 3:40
Posts: 6
Location: india
@fzabkar
It worked, and a lot of thanks for your support. :D


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 9 posts ] 

All times are UTC - 5 hours [ DST ]


Who is online

Users browsing this forum: elektek and 37 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group