All times are UTC - 5 hours [ DST ]




Post new topic Reply to topic  [ 7 posts ] 
Author Message
 Post subject: ST1000DM003-1CH162 Problem
PostPosted: February 18th, 2019, 2:33 
Offline

Joined: January 18th, 2010, 23:53
Posts: 165
Location: india
In Terminal just getting

Quote:
Boot 0x40M
Spin Up
FAIL Servo Op=0100 Resp=0007
0100 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000
ResponseFrame 1BC0 0073 07CA 3540 0008 0000 0000 0000 0FFF 0000 0000 0000 0000 0000 0000 0000 1293 2699 FFFF 2000 20CC 0002 0000 4014 0000 4014 0000 2247 0000 0020 001F 0007 0010
FAIL Servo Op=0100 Resp=0003
0100 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000
ResponseFrame 2040 0077 07CA 3540 0008 0000 0000 0000 0FFF 0000 0000 0000 0000 0000 0000 0000 1293 2699 FFFF 2000 20CC 0002 0000 4014 0000 4014 0000 007F 0004 0020 001F 0004 0000


Just two clicks then spin down.
What is the problem?

when head changed then also get the same result.


Top
 Profile  
 
 Post subject: Re: ST1000DM003-1CH162 Problem
PostPosted: February 18th, 2019, 3:42 
Offline

Joined: November 29th, 2006, 10:08
Posts: 7464
Location: UK
What happens when you put heads back in donor?

_________________
PC Image Data Recovery
http://www.pcimage.co.uk

New!! HDD-PCB.COM for all your PCB and donor HDD requirements!


Top
 Profile  
 
 Post subject: Re: ST1000DM003-1CH162 Problem
PostPosted: February 18th, 2019, 6:06 
Offline

Joined: February 2nd, 2019, 1:21
Posts: 163
Location: Sri Lanka
i think platter problem. sometimes your donor heads will not work now. if donor heads work with donor hard, just change the pcb.


Top
 Profile  
 
 Post subject: Re: ST1000DM003-1CH162 Problem
PostPosted: February 18th, 2019, 8:38 
Offline

Joined: January 18th, 2010, 23:53
Posts: 165
Location: india
Yes , After head swap donor is not working.

is there any chance to recover?


Top
 Profile  
 
 Post subject: Re: ST1000DM003-1CH162 Problem
PostPosted: February 18th, 2019, 11:39 
Offline

Joined: November 29th, 2006, 10:08
Posts: 7464
Location: UK
gps31 wrote:
Yes , After head swap donor is not working.

is there any chance to recover?


In which case there are two explanations that spring to mind...

1. Your head swap didn't go well, it got messed up.
2. The drive has media damage on one or more of the platter surfaces.

Probably has a chance of partial recovery, if you know what you're doing.

_________________
PC Image Data Recovery
http://www.pcimage.co.uk

New!! HDD-PCB.COM for all your PCB and donor HDD requirements!


Top
 Profile  
 
 Post subject: Re: ST1000DM003-1CH162 Problem
PostPosted: February 19th, 2019, 11:11 
Offline

Joined: February 2nd, 2019, 1:21
Posts: 163
Location: Sri Lanka
if you used cleanroom and proper tools for head swapped, most of time platter has degrade problem, sometimes magnet dust on the platter. specially platter 0. so you have well experiance you can clean the platters. after cleaning platters don't use new donor heads for very first time. normally i have small collection of weak heads and use weak donor heads for 1st time and see results.


Top
 Profile  
 
 Post subject: Re: ST1000DM003-1CH162 Problem
PostPosted: February 19th, 2019, 14:36 
Offline
User avatar

Joined: December 8th, 2013, 4:48
Posts: 774
Location: Pakistan
can you upload the ROM of both patient and donor, just to verify that heads are compatible in the first place ?

_________________
Data Recovery Pakistan


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 7 posts ] 

All times are UTC - 5 hours [ DST ]


Who is online

Users browsing this forum: pepe and 29 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group