All times are UTC - 5 hours [ DST ]




Post new topic Reply to topic  [ 11 posts ] 
Author Message
 Post subject: Loader for WD10SPZX-22Z10T1
PostPosted: April 7th, 2021, 5:18 
Offline

Joined: August 12th, 2014, 17:52
Posts: 12
Location: Germany
Hello everybody,

does anybody have a loader for WD10SPZX-22Z10T1 - Firmware Version is 0005008J.

Thank you very much.


Top
 Profile  
 
 Post subject: Re: Loader for WD10SPZX-22Z10T1
PostPosted: April 7th, 2021, 9:09 
Offline

Joined: August 12th, 2014, 17:52
Posts: 12
Location: Germany
I just found a possible one at http://files.hddguru.com/download/PC-30 ... ty/Palmer/
I will try it.


Top
 Profile  
 
 Post subject: Re: Loader for WD10SPZX-22Z10T1
PostPosted: April 7th, 2021, 9:32 
Offline

Joined: August 12th, 2014, 17:52
Posts: 12
Location: Germany
Very strange. I tried a loader from same firmware version 0005008J that i found at http://files.hddguru.com/download/PC-30 ... ty/Palmer/ but when I try to upload loader PC3K says: VCS ERR OFF TOO LARGE.

Is this possible? Same Fimware Version, but different loader?


Top
 Profile  
 
 Post subject: Re: Loader for WD10SPZX-22Z10T1
PostPosted: April 7th, 2021, 10:25 
Offline

Joined: May 30th, 2005, 17:07
Posts: 528
Hi,
Here you are

Mikippp


Attachments:
05.8JD.zip [743.07 KiB]
Downloaded 479 times
Top
 Profile  
 
 Post subject: Re: Loader for WD10SPZX-22Z10T1
PostPosted: April 7th, 2021, 11:31 
Offline

Joined: August 12th, 2014, 17:52
Posts: 12
Location: Germany
Thank you very much. Unfortunatly it says: VSC ERR OFF TOO LARGE.

But I found one in http://files.hddguru.com/download/PC-30 ... ty/Palmer/

"WDC WD10SPZX-00Z10T0-01-01A01-WD-WXH1A88A10X9.rar
WD10SPZX-00Z10T0 - ROM F/W version: 00050006"

This one worked fine. Unfortunatly HDD won't get good access to SA.

I can do a Head Test and it works fine with no errors, but I can't read the modules... Does this make any sense?

Any Idea about this case?

Thank you very much.


Top
 Profile  
 
 Post subject: Re: Loader for WD10SPZX-22Z10T1
PostPosted: April 9th, 2021, 1:48 
Offline

Joined: November 29th, 2006, 10:08
Posts: 7843
Location: UK
Stupid question, but I assume you're using a special "unlocked" PCB?

_________________
PC Image Data Recovery
http://www.pcimage.co.uk

New!! HDD-PCB.COM for all your PCB and donor HDD requirements!


Top
 Profile  
 
 Post subject: Re: Loader for WD10SPZX-22Z10T1
PostPosted: April 9th, 2021, 12:45 
Offline

Joined: August 12th, 2014, 17:52
Posts: 12
Location: Germany
pcimage wrote:
Stupid question, but I assume you're using a special "unlocked" PCB?


Yes, I use an unlocked PCB.


Top
 Profile  
 
 Post subject: Re: Loader for WD10SPZX-22Z10T1
PostPosted: April 9th, 2021, 13:00 
Offline
User avatar

Joined: June 11th, 2013, 17:01
Posts: 1710
Location: Phoenix, AZ USA
Have you checked if its the original ROM?
You can do this by checking the WWN number.

_________________
HDD, SSD, Flash and RAID Data Recovery
Founder of The Data Recovery Professionals Group


Top
 Profile  
 
 Post subject: Re: Loader for WD10SPZX-22Z10T1
PostPosted: April 23rd, 2021, 8:17 
Offline

Joined: August 12th, 2014, 17:52
Posts: 12
Location: Germany
ddrecovery wrote:
Have you checked if its the original ROM?
You can do this by checking the WWN number.


Yes it's Original ROM. I got a Loader that's working fine, but I can't upload module 01.

After making upload of loader, when ein try to go into techno mode I get the following:
Techno mode key
Techno mode key......................... : Ok

RAM:
HDD Info reading........................ : Ok
Heads number............................ : 2
Cyl Count............................... : 512

Zone allocation table................... : HDDs RAM reading error Device Error Detected: "SCT INVALID FUNCTION CODE"

ROM:
Read ROM................................ : Ok
ROM Data size........................... : 1024 Kb
Flash ROM dir reading................... : Ok (Active)
Flash ROM dir reading (Ext)............. : Ok
Modules directory address............... : 0
SA regions address...................... : by default
SA regions address (RAM)................ : by default
Module 02 access........................ : Granted
SA Translator loading................... : No S/A SPT info avalable

ROM Modules:
ROM version............................. : 05.06B
ROM F/W version......................... : 0005008J
Overlay F/W version..................... : 05.07B
Servo F/W version....................... : 03.64

Heads configuration..................... : by map
Heads number............................ : 2
Heads number in use..................... : 2
Switched off heads...................... : No
Heads map............................... : 0,1

Service area:
Power up log reading.................... : Ok
Dir data................................ : No
Permanent overlay....................... : Yes
CFG data................................ : No
SA dir reading (ID)..................... : Module ID 01 reading error Device Error Detected: "DISK ECU UNSAFE ERROR"
SA SPT Detect........................... : FAIL
SA dir reading (ABA/CHS)................ : Module 01 reading error: ABA 3 C:1(1) reading error Device Error Detected: "DISK ECU UNSAFE ERROR"
SA Access............................... : Copy 0,Copy 1

Configuration reading................... : Module ID 02 reading error Device Error Detected: "DISK ECU UNSAFE ERROR"


Any Idea, what I could do?


Top
 Profile  
 
 Post subject: Re: Loader for WD10SPZX-22Z10T1
PostPosted: April 23rd, 2021, 19:12 
Offline
User avatar

Joined: December 8th, 2013, 4:48
Posts: 831
Location: Pakistan
navideira wrote:
ddrecovery wrote:
Have you checked if its the original ROM?
You can do this by checking the WWN number.


Yes it's Original ROM. I got a Loader that's working fine, but I can't upload module 01.

After making upload of loader, when ein try to go into techno mode I get the following:
Techno mode key
Techno mode key......................... : Ok

RAM:
HDD Info reading........................ : Ok
Heads number............................ : 2
Cyl Count............................... : 512

Zone allocation table................... : HDDs RAM reading error Device Error Detected: "SCT INVALID FUNCTION CODE"

ROM:
Read ROM................................ : Ok
ROM Data size........................... : 1024 Kb
Flash ROM dir reading................... : Ok (Active)
Flash ROM dir reading (Ext)............. : Ok
Modules directory address............... : 0
SA regions address...................... : by default
SA regions address (RAM)................ : by default
Module 02 access........................ : Granted
SA Translator loading................... : No S/A SPT info avalable

ROM Modules:
ROM version............................. : 05.06B
ROM F/W version......................... : 0005008J
Overlay F/W version..................... : 05.07B
Servo F/W version....................... : 03.64

Heads configuration..................... : by map
Heads number............................ : 2
Heads number in use..................... : 2
Switched off heads...................... : No
Heads map............................... : 0,1

Service area:
Power up log reading.................... : Ok
Dir data................................ : No
Permanent overlay....................... : Yes
CFG data................................ : No
SA dir reading (ID)..................... : Module ID 01 reading error Device Error Detected: "DISK ECU UNSAFE ERROR"
SA SPT Detect........................... : FAIL
SA dir reading (ABA/CHS)................ : Module 01 reading error: ABA 3 C:1(1) reading error Device Error Detected: "DISK ECU UNSAFE ERROR"
SA Access............................... : Copy 0,Copy 1

Configuration reading................... : Module ID 02 reading error Device Error Detected: "DISK ECU UNSAFE ERROR"


Any Idea, what I could do?


write donor rom with blocked SA access than used its loader, you will get SA access. I hope than you rule out the problem.

_________________
Data Recovery Pakistan


Top
 Profile  
 
 Post subject: Re: Loader for WD10SPZX-22Z10T1
PostPosted: April 26th, 2021, 13:32 
Offline

Joined: August 12th, 2014, 17:52
Posts: 12
Location: Germany
Quote:
write donor rom with blocked SA access than used its loader, you will get SA access. I hope than you rule out the problem.


Thank you very much MindMergepk. Unfortunately I didn't get access to SA. Please find new output.
Any other Idea?

Techno mode key
Techno mode key......................... : Ok

RAM:
HDD Info reading........................ : Ok
Heads number............................ : 2
Cyl Count............................... : 512

ROM:
Read ROM................................ : Ok
ROM Data size........................... : 1024 Kb
Flash ROM dir reading................... : Ok (Active)
Flash ROM dir reading (Ext)............. : Ok
Modules directory address............... : 0
SA regions address...................... : by default
Module 02 access........................ : Granted
ROM Modules:
ROM version............................. : 05.06B
ROM F/W version......................... : 00050006
Overlay F/W version..................... : 05.06B
Servo F/W version....................... : 03.64

Heads configuration..................... : by map
Heads number............................ : 2
Heads number in use..................... : 2
Switched off heads...................... : No
Heads map............................... : 0,1


Cache ovl(10) data uploading............ : Ok
Permanent ovl (11) data uploading....... : Ok
Resources folder........................ : C:\Program Files (x86)\ACE Lab\PC-3000\Bin\!Profiles\WDCMarvell\Palmer\WDC WD10SPZX-00Z10T0-01-01A01-WD-WXH1A88A10X9\Data\SABackup\Modules\Copy 0
Static module reading error Device Error Detected: "VSC ERR STATIC FILE INVALID"
Techno mode key
Techno mode key......................... : Ok

RAM:
HDD Info reading........................ : Ok
Heads number............................ : 2
Cyl Count............................... : 512

Zone allocation table................... : HDDs RAM reading error Device Error Detected: "SCT INVALID FUNCTION CODE"

ROM:
Read ROM................................ : Ok
ROM Data size........................... : 1024 Kb
Flash ROM dir reading................... : Ok
Flash ROM dir reading (Ext)............. : Ok (Active)
Modules directory address............... : 0
SA regions address...................... : by default
SA regions address (RAM)................ : by default
Module 02 access........................ : Granted
SA Translator loading................... : No S/A SPT info avalable

ROM Modules:
ROM version............................. : 05.06B
ROM F/W version......................... : 00050006
Overlay F/W version..................... : 05.07B
Servo F/W version....................... : 03.64

Heads configuration..................... : by map
Heads number............................ : 2
Heads number in use..................... : 2
Switched off heads...................... : No
Heads map............................... : 0,1

Service area:
Power up log reading.................... : Ok
Dir data................................ : No
Permanent overlay....................... : Yes
CFG data................................ : No
SA dir reading (ID)..................... : Module ID 01 reading error Device Error Detected: "DISK DAM ERROR"
SA SPT Detect........................... : FAIL
SA dir reading (ABA/CHS)................ : Module 01 reading error: ABA 0 C:1(1) reading error Device Error Detected: "DISK ECU UNSAFE ERROR"
SA Access............................... : Copy 0,Copy 1

Configuration reading................... : Module ID 02 reading error Device Error Detected: "DISK DAM ERROR"


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 11 posts ] 

All times are UTC - 5 hours [ DST ]


Who is online

Users browsing this forum: Google [Bot] and 58 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group