I bought 8 2tb drives off eBay, they had type 2 protection on them so I sg_format -v -F /dev/sdX and removed the protection on all the drives.
They all show up in Proxmox and I can make a ZFS pool and write to the pool without any issues.
During the sg-format of /dev/sdd, the power blinked out for a second. The T610 was on my bench top while I setup the machine and was not on battery backup.
After booting the machine back up, the HDD light for that drive will blink on during self test and when read/write ops are happening but it will not stay on when idle like the other 7 drives.
Everything else seems ok. Should I keep investigating or just ignore it.
This is the drive in question, /dev/sdd.
Below this code block is another drive from the 8 I bought that is working properly, /dev/sde
Code:
root@pve:~# smartctl -x /dev/sdd
smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.131-2-pve] (local build)
Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Vendor: IBM-D050
Product: ST2000NX0263
Revision: BD4D
Compliance: SPC-4
User Capacity: 2,000,398,934,016 bytes [2.00 TB]
Logical block size: 4096 bytes
LU is fully provisioned
Rotation Rate: 7200 rpm
Form Factor: 2.5 inches
Logical Unit id: 0x5000c500b860642f
Serial number: W461BTAD0000E841JMR9
Device type: disk
Transport protocol: SAS (SPL-3)
Local Time is: Wed Jan 10 07:36:59 2024 EST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
Temperature Warning: Enabled
Read Cache is: Enabled
Writeback Cache is: Disabled
=== START OF READ SMART DATA SECTION ===
SMART Health Status: OK
Grown defects during certification = 0
Total blocks reassigned during format = 0
Total new blocks reassigned = 0
Power on minutes since format = 833
Current Drive Temperature: 35 C
Drive Trip Temperature: 65 C
Elements in grown defect list: 0
Error counter log:
Errors Corrected by Total Correction Gigabytes Total
ECC rereads/ errors algorithm processed uncorrected
fast | delayed rewrites corrected invocations [10^9 bytes] errors
read: 2851836772 0 0 2851836772 0 291215.743 0
write: 0 0 0 0 0 143605.909 0
verify: 1928732332 0 0 1928732332 0 2215.588 0
Non-medium error count: 608
SMART Self-test log
Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ]
Description number (hours)
# 1 Background short Completed - 0 - [- - -]
Long (extended) Self-test duration: 20400 seconds [340.0 minutes]
Background scan results log
Status: waiting until BMS interval timer expires
Accumulated power on time, hours:minutes 34689:44 [2081384 minutes]
Number of background scans performed: 216, scan progress: 0.00%
Number of background medium scans performed: 216
Protocol Specific port log page for SAS SSP
relative target port id = 1
generation code = 0
number of phys = 1
phy identifier = 0
attached device type: SAS or SATA device
attached reason: unknown
reason: unknown
negotiated logical link rate: phy enabled; 6 Gbps
attached initiator port: ssp=1 stp=1 smp=1
attached target port: ssp=0 stp=0 smp=0
SAS address = 0x5000c500b860642d
attached SAS address = 0x5d4ae520ac07d993
attached phy identifier = 1
Invalid DWORD count = 8
Running disparity error count = 8
Loss of DWORD synchronization = 11
Phy reset problem = 0
Phy event descriptors:
Invalid word count: 8
Running disparity error count: 8
Loss of dword synchronization count: 11
Phy reset problem count: 0
relative target port id = 2
generation code = 0
number of phys = 1
phy identifier = 1
attached device type: no device attached
attached reason: unknown
reason: unknown
negotiated logical link rate: phy enabled; unknown
attached initiator port: ssp=0 stp=0 smp=0
attached target port: ssp=0 stp=0 smp=0
SAS address = 0x5000c500b860642e
attached SAS address = 0x0
attached phy identifier = 0
Invalid DWORD count = 0
Running disparity error count = 0
Loss of DWORD synchronization = 0
Phy reset problem = 0
Phy event descriptors:
Invalid word count: 0
Running disparity error count: 0
Loss of dword synchronization count: 0
Phy reset problem count: 0
Code:
root@pve:~# smartctl -x /dev/sde
smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.131-2-pve] (local build)
Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Vendor: IBM-D050
Product: ST2000NX0263
Revision: BD4D
Compliance: SPC-4
User Capacity: 2,000,398,934,016 bytes [2.00 TB]
Logical block size: 4096 bytes
LU is fully provisioned
Rotation Rate: 7200 rpm
Form Factor: 2.5 inches
Logical Unit id: 0x5000c500b860581f
Serial number: W461BS5B0000E84200DS
Device type: disk
Transport protocol: SAS (SPL-3)
Local Time is: Wed Jan 10 07:38:09 2024 EST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
Temperature Warning: Enabled
Read Cache is: Enabled
Writeback Cache is: Disabled
=== START OF READ SMART DATA SECTION ===
SMART Health Status: OK
Grown defects during certification = 0
Total blocks reassigned during format = 0
Total new blocks reassigned = 0
Power on minutes since format = 2896
Current Drive Temperature: 34 C
Drive Trip Temperature: 65 C
Elements in grown defect list: 0
Error counter log:
Errors Corrected by Total Correction Gigabytes Total
ECC rereads/ errors algorithm processed uncorrected
fast | delayed rewrites corrected invocations [10^9 bytes] errors
read: 123644058 0 0 123644058 0 302089.360 0
write: 0 0 0 0 0 141515.484 0
verify: 1889425582 0 0 1889425582 0 2205.915 0
Non-medium error count: 2
SMART Self-test log
Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ]
Description number (hours)
# 1 Background short Completed - 0 - [- - -]
Long (extended) Self-test duration: 20400 seconds [340.0 minutes]
Background scan results log
Status: waiting until BMS interval timer expires
Accumulated power on time, hours:minutes 34689:10 [2081350 minutes]
Number of background scans performed: 215, scan progress: 0.00%
Number of background medium scans performed: 215
Protocol Specific port log page for SAS SSP
relative target port id = 1
generation code = 0
number of phys = 1
phy identifier = 0
attached device type: SAS or SATA device
attached reason: unknown
reason: unknown
negotiated logical link rate: phy enabled; 6 Gbps
attached initiator port: ssp=1 stp=1 smp=1
attached target port: ssp=0 stp=0 smp=0
SAS address = 0x5000c500b860581d
attached SAS address = 0x5d4ae520ac07d994
attached phy identifier = 2
Invalid DWORD count = 0
Running disparity error count = 0
Loss of DWORD synchronization = 2
Phy reset problem = 0
Phy event descriptors:
Invalid word count: 0
Running disparity error count: 0
Loss of dword synchronization count: 2
Phy reset problem count: 0
relative target port id = 2
generation code = 0
number of phys = 1
phy identifier = 1
attached device type: no device attached
attached reason: unknown
reason: unknown
negotiated logical link rate: phy enabled; unknown
attached initiator port: ssp=0 stp=0 smp=0
attached target port: ssp=0 stp=0 smp=0
SAS address = 0x5000c500b860581e
attached SAS address = 0x0
attached phy identifier = 0
Invalid DWORD count = 0
Running disparity error count = 0
Loss of DWORD synchronization = 0
Phy reset problem = 0
Phy event descriptors:
Invalid word count: 0
Running disparity error count: 0
Loss of dword synchronization count: 0
Phy reset problem count: 0
FAQ
Search
Login
Register
HDDGURU FILES
