All times are UTC - 5 hours [ DST ]




Post new topic Reply to topic  [ 24 posts ]  Go to page 1, 2  Next
Author Message
 Post subject: Cell Phone Chip Cover Removal
PostPosted: July 9th, 2016, 18:17 
Offline
User avatar

Joined: June 11th, 2013, 17:01
Posts: 1710
Location: Phoenix, AZ USA
Any advice on the best way to remove the silver metal chip covers from this cell phone board.
I have a hot air station, solder station and I/R SMD/BGA rework station.


Attachments:
20160624_142811_resized.jpg
20160624_142811_resized.jpg [ 1.29 MiB | Viewed 17678 times ]

_________________
HDD, SSD, Flash and RAID Data Recovery
Founder of The Data Recovery Professionals Group
Top
 Profile  
 
 Post subject: Re: Cell Phone Chip Cover Removal
PostPosted: July 9th, 2016, 19:31 
Offline

Joined: July 30th, 2012, 3:37
Posts: 310
Location: Fairfield, CT USA
Carefully :-)

Hot air would be my preference assuming you have a decent station

_________________
Recover My Flash Drive


Top
 Profile  
 
 Post subject: Re: Cell Phone Chip Cover Removal
PostPosted: July 11th, 2016, 18:22 
Offline

Joined: October 16th, 2013, 13:21
Posts: 713
Location: Brazil
Also, depending of what there is on the other side of the board, and if the board needs or not to be restored to function later, you can use a hot plate ( sorry, forgot the right name, like a clothes iron business side up ) on the underside to help warming the board.


Top
 Profile  
 
 Post subject: Re: Cell Phone Chip Cover Removal
PostPosted: July 11th, 2016, 19:15 
Offline
User avatar

Joined: June 11th, 2013, 17:01
Posts: 1710
Location: Phoenix, AZ USA
Thanks guys. I did get the covers off and got to the eMMC chip. Unusually (at least I think so), this eMMC chip was not encrypted, XOR'd or anything else. Got the folder structure just by reading it. Looks like the phone just used if for storage. Thanks again.

_________________
HDD, SSD, Flash and RAID Data Recovery
Founder of The Data Recovery Professionals Group


Top
 Profile  
 
 Post subject: Re: Cell Phone Chip Cover Removal
PostPosted: July 12th, 2016, 12:24 
Offline

Joined: October 24th, 2009, 15:22
Posts: 872
Location: Poland
Of course it use XOR or anything else. eMMC chip has inside controller and memory chip. If controller works, you can access data similar like for SD card or pendrive.

_________________
Flash Killer - everyday new resources (pinout, XOR, ECC,config) for flash devices


Top
 Profile  
 
 Post subject: Re: Cell Phone Chip Cover Removal
PostPosted: July 12th, 2016, 12:32 
Offline
User avatar

Joined: June 11th, 2013, 17:01
Posts: 1710
Location: Phoenix, AZ USA
arvika wrote:
Of course it use XOR or anything else. eMMC chip has inside controller and memory chip. If controller works, you can access data similar like for SD card or pendrive.

Sorry, what I meant to say was that we didn't need to apply XOR or any other conversion.

_________________
HDD, SSD, Flash and RAID Data Recovery
Founder of The Data Recovery Professionals Group


Top
 Profile  
 
 Post subject: Re: Cell Phone Chip Cover Removal
PostPosted: July 12th, 2016, 13:39 
Offline
User avatar

Joined: April 3rd, 2011, 0:19
Posts: 2003
Location: Providence, RI
What are you using for an eMMC reader? I really try to stay away from the phone recoveries, but have been considering buying at least an eMMC reader. I know they are now even using eMMC in cheap-o laptops at Best Buy, so probably will be seeing a lot more of them soon.

_________________
Data Medics - Hard Drive, SSD, and RAID Data Recovery Service Company


Top
 Profile  
 
 Post subject: Re: Cell Phone Chip Cover Removal
PostPosted: July 12th, 2016, 14:40 
Offline
User avatar

Joined: June 11th, 2013, 17:01
Posts: 1710
Location: Phoenix, AZ USA
data-medics wrote:
What are you using for an eMMC reader? I really try to stay away from the phone recoveries, but have been considering buying at least an eMMC reader. I know they are now even using eMMC in cheap-o laptops at Best Buy, so probably will be seeing a lot more of them soon.

I have a set of the new Rusolut eMMC adapters. They plug into any commercially available eMMC reader.

_________________
HDD, SSD, Flash and RAID Data Recovery
Founder of The Data Recovery Professionals Group


Top
 Profile  
 
 Post subject: Re: Cell Phone Chip Cover Removal
PostPosted: July 12th, 2016, 15:42 
Offline

Joined: October 24th, 2009, 15:22
Posts: 872
Location: Poland
Rusolut adapters looks like on photos below. Very good tool, every eMMC chip has own adapter - they have different sizes, fits very well to socket. No problem with positioning, no risk that you connect VCC to GND pad etc. You connect adapter like SD card.


Attachments:
DSC_0012_.jpg
DSC_0012_.jpg [ 275.63 KiB | Viewed 17509 times ]
DSC_0009_.jpg
DSC_0009_.jpg [ 289.52 KiB | Viewed 17509 times ]
DSC_0006_.jpg
DSC_0006_.jpg [ 313.26 KiB | Viewed 17509 times ]

_________________
Flash Killer - everyday new resources (pinout, XOR, ECC,config) for flash devices
Top
 Profile  
 
 Post subject: Re: Cell Phone Chip Cover Removal
PostPosted: July 23rd, 2016, 14:31 
Offline

Joined: July 30th, 2012, 3:37
Posts: 310
Location: Fairfield, CT USA
ddrecovery wrote:
Any advice on the best way to remove the silver metal chip covers from this cell phone board.
I have a hot air station, solder station and I/R SMD/BGA rework station.


Use Chip Quik SMD Removal Alloy. It lowers the melting point of the solder.

_________________
Recover My Flash Drive


Top
 Profile  
 
 Post subject: Re: Cell Phone Chip Cover Removal
PostPosted: July 23rd, 2016, 21:20 
Offline

Joined: December 8th, 2010, 11:37
Posts: 738
Location: Ottawa, Canada
jeremyb wrote:
ddrecovery wrote:
Any advice on the best way to remove the silver metal chip covers from this cell phone board.
I have a hot air station, solder station and I/R SMD/BGA rework station.


Use Chip Quik SMD Removal Alloy. It lowers the melting point of the solder.

ChipQuik requires that the lead-free solder reach liquidus (217C) so the Bismuth can blend to form the allow with its lower melting temperature, so I don't see how that would work here. I would expect a hot air or IR BGA rework station would be required but have no personal experience with this device.

_________________
Sabo Computer Repairs & Data Recovery


Top
 Profile  
 
 Post subject: Re: Cell Phone Chip Cover Removal
PostPosted: July 24th, 2016, 3:06 
Offline

Joined: July 30th, 2012, 3:37
Posts: 310
Location: Fairfield, CT USA
LarrySabo wrote:
jeremyb wrote:
ddrecovery wrote:
Any advice on the best way to remove the silver metal chip covers from this cell phone board.
I have a hot air station, solder station and I/R SMD/BGA rework station.


Use Chip Quik SMD Removal Alloy. It lowers the melting point of the solder.

ChipQuik requires that the lead-free solder reach liquidus (217C) so the Bismuth can blend to form the allow with its lower melting temperature, so I don't see how that would work here. I would expect a hot air or IR BGA rework station would be required but have no personal experience with this device.


According to the manufactures site:
Chip Quik Alloy Melting Point: 58 Celsius (136 F)

That's practically nothing. Use your iron to add some of this stuff in with the lead-free solder, just be careful because if this stuff gets on any passives they'll float off the PCB while you're using hot air.

_________________
Recover My Flash Drive


Top
 Profile  
 
 Post subject: Re: Cell Phone Chip Cover Removal
PostPosted: July 24th, 2016, 8:10 
Offline

Joined: December 8th, 2010, 11:37
Posts: 738
Location: Ottawa, Canada
jeremyb wrote:
According to the manufactures site:
Chip Quik Alloy Melting Point: 58 Celsius (136 F)

That's the melting point of the alloy, but to become an alloy, the bismuth needs to mix with the lead-free solder, which means it has to reach 217c. I can't see how/where the metal covers are bonded to the board/chips and assumed the solder joints are hidden beneath the metal. If they are at the edges, then sure, give ChipQuik a try.

As for hot air versus IR, I think hot air would be his best bet, since the IR will not likely be absorbed well by the metal covers.

_________________
Sabo Computer Repairs & Data Recovery


Top
 Profile  
 
 Post subject: Re: Cell Phone Chip Cover Removal
PostPosted: July 24th, 2016, 15:31 
Offline

Joined: July 30th, 2012, 3:37
Posts: 310
Location: Fairfield, CT USA
LarrySabo wrote:
jeremyb wrote:
According to the manufactures site:
Chip Quik Alloy Melting Point: 58 Celsius (136 F)

That's the melting point of the alloy, but to become an alloy, the bismuth needs to mix with the lead-free solder, which means it has to reach 217c. I can't see how/where the metal covers are bonded to the board/chips and assumed the solder joints are hidden beneath the metal. If they are at the edges, then sure, give ChipQuik a try.

As for hot air versus IR, I think hot air would be his best bet, since the IR will not likely be absorbed well by the metal covers.


You're argument is that since you've never tried it then there is no chance of success?
If you look at the picture you'll see the tabs bonding the covers to the PCB are on the outside..

_________________
Recover My Flash Drive


Top
 Profile  
 
 Post subject: Re: Cell Phone Chip Cover Removal
PostPosted: July 24th, 2016, 16:23 
Offline

Joined: December 8th, 2010, 11:37
Posts: 738
Location: Ottawa, Canada
jeremyb wrote:
You're argument is that since you've never tried it then there is no chance of success?
If you look at the picture you'll see the tabs bonding the covers to the PCB are on the outside..

My argument was based on my ignorance of where the covers were attached to the PCB. If the OP can get a soldering iron into the joints, ChipQuik should help a lot. If not, a hot air rework tool should do the trick.

Mainly, I was trying to point out that ChipQuik still requires the solder to reach 217C in order to blend with the bismuth to form the alloy. :)

_________________
Sabo Computer Repairs & Data Recovery


Top
 Profile  
 
 Post subject: Re: Cell Phone Chip Cover Removal
PostPosted: July 24th, 2016, 16:39 
Offline
User avatar

Joined: June 11th, 2013, 17:01
Posts: 1710
Location: Phoenix, AZ USA
Sorry for my slow respose, I have been training in Poland for the last week.

I did use a mixture of Chip Quick and brute force. The phone was water damaged beyond repair so chip removal was the only option. As I didn't need to save the board, I used CQ on one side of each cover and kept heating until it came loose, I could then lift the cover off from the one side and peel it back from the board. Not recommended if you need to save the board, but this doesn't affect the chips.

I did try hot air, but the heat disipation was too great and could never get all the cover heated at once, or at least I was concerned about the chip temp inside the cover. That's when I went for CQ. IR may work, will try that next time.

_________________
HDD, SSD, Flash and RAID Data Recovery
Founder of The Data Recovery Professionals Group


Top
 Profile  
 
 Post subject: Re: Cell Phone Chip Cover Removal
PostPosted: July 24th, 2016, 20:33 
Offline

Joined: July 30th, 2012, 3:37
Posts: 310
Location: Fairfield, CT USA
Deleted by me

_________________
Recover My Flash Drive


Last edited by jeremyb on July 24th, 2016, 20:37, edited 1 time in total.

Top
 Profile  
 
 Post subject: Re: Cell Phone Chip Cover Removal
PostPosted: July 24th, 2016, 20:36 
Offline

Joined: July 30th, 2012, 3:37
Posts: 310
Location: Fairfield, CT USA
LarrySabo wrote:
Mainly, I was trying to point out that ChipQuik still requires the solder to reach 217C in order to blend with the bismuth to form the alloy. :)
I'm not sure, It seems like it amplifies the heat if that makes any sense like insulation.. Cool stuff

ddrecovery wrote:
Sorry for my slow respose, I have been training in Poland for the last week.

Learn any good tricks?

_________________
Recover My Flash Drive


Top
 Profile  
 
 Post subject: Re: Cell Phone Chip Cover Removal
PostPosted: July 25th, 2016, 10:37 
Offline
User avatar

Banned User

Joined: July 17th, 2016, 5:01
Posts: 4
Location: Bangladesh
jeremyb wrote:
ddrecovery wrote:
Any advice on the best way to remove the silver metal chip covers from this cell phone board.
I have a hot air station, solder station and I/R SMD/BGA rework station.


Use Chip Quik SMD Removal Alloy. It lowers the melting point of the solder.


Does it really work?


Top
 Profile  
 
 Post subject: Re: Cell Phone Chip Cover Removal
PostPosted: July 25th, 2016, 12:07 
Offline
User avatar

Joined: June 11th, 2013, 17:01
Posts: 1710
Location: Phoenix, AZ USA
jeremyb wrote:
Learn any good tricks?

Yes, but not of any interest to NAND bods, it was a RAID recovery class with D3 Consulting. VNR is next :-)

_________________
HDD, SSD, Flash and RAID Data Recovery
Founder of The Data Recovery Professionals Group


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 24 posts ]  Go to page 1, 2  Next

All times are UTC - 5 hours [ DST ]


Who is online

Users browsing this forum: No registered users and 15 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group