HDD GURU FORUMS http://forum.hddguru.com/ |
|
Monolith SD Card Sandisk - > 8 Bit Or 16 Bit Pinout Wiring http://forum.hddguru.com/viewtopic.php?f=10&t=35999 |
Page 1 of 1 |
Author: | Amarbir[CDR-Labs] [ October 27th, 2017, 5:42 ] |
Post subject: | Monolith SD Card Sandisk - > 8 Bit Or 16 Bit Pinout Wiring |
Hello To all My Seniors , I wanted to ask you that if i have a 16 Bit pinout SD Card From Sandisk And its Wired for 8 Bit Can it still Read Its ID Properly ? . I have one more question but i will ask after i get a reply to this one .I have a Sandisk Extreme 32 GB SD Card That is Iding Like 0x98009082 72570904 and i cannot pass Read ID section in PC3K .TS Guys Says ID is Not Correct ,I have Wired For SDHC Type 4 8 Bit pinout for this Sandisk .I checked all my connections are ok ,Micro Switch 1,2,3,4,5 are off and 6 is on .I2 that is WP is not connected .Also i have used VCC and GND from main pins and i have connected nothing to F1 and J1 VCC and K1 GND as i feel vcc and gnd can travel to that pins from main points of sd card .Shall i try and connect these three points . |
Author: | arvika [ October 27th, 2017, 7:20 ] |
Post subject: | Re: Monolith SD Card Sandisk - > 8 Bit Or 16 Bit Pinout Wiri |
Try on other reader to verify. It is typical problem with incorrect ID for monolith on PC3K reader. But it can be also some internal problem with chip or soldering. |
Author: | Amarbir[CDR-Labs] [ October 27th, 2017, 7:37 ] |
Post subject: | Re: Monolith SD Card Sandisk - > 8 Bit Or 16 Bit Pinout Wiri |
arvika wrote: Try on other reader to verify. It is typical problem with incorrect ID for monolith on PC3K reader. But it can be also some internal problem with chip or soldering. , This is The Problem Arvika Sir I have a single Horse Called PC3K Flash .Good Thing Would Be To Get The Hardware Part of Softcenter At Least As Soon As i Can Afford ,But in anycase Can You suggest How And what i Can Try |
Author: | HaQue [ October 27th, 2017, 17:30 ] |
Post subject: | Re: Monolith SD Card Sandisk - > 8 Bit Or 16 Bit Pinout Wiri |
buy a SC reader :-0 |
Author: | pcimage [ October 27th, 2017, 18:07 ] |
Post subject: | Re: Monolith SD Card Sandisk - > 8 Bit Or 16 Bit Pinout Wiri |
HaQue wrote: buy a SC reader :-0 Yeah, it’s cheap and good! Not fancy, but it works. Don’t forget to add the appropriate adaptors and the new voltage board! |
Author: | Amarbir[CDR-Labs] [ October 28th, 2017, 6:51 ] |
Post subject: | Re: Monolith SD Card Sandisk - > 8 Bit Or 16 Bit Pinout Wiri |
pcimage wrote: HaQue wrote: buy a SC reader :-0 Yeah, it’s cheap and good! Not fancy, but it works. Don’t forget to add the appropriate adaptors and the new voltage board! Sean Sir , I will skip the power adapter i plan to make one in different design myself |
Page 1 of 1 | All times are UTC - 5 hours [ DST ] |
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |