All times are UTC - 5 hours [ DST ]




Post new topic Reply to topic  [ 6 posts ] 
Author Message
 Post subject: Is everything good with my SSD??
PostPosted: November 9th, 2017, 18:26 
Offline

Joined: November 9th, 2017, 15:37
Posts: 3
Location: Europe
I have Kingston HyperX Fury 120GB. In SMART tab I have couple of Raw read error rate values, at least I think :? :(

Only in this program (Active hard disk monitor) I got this many bad Smart values:
Image

In other programs everything seems fine except there are some read error rate but Smart says it OK.

Kingston SSD manager

Image

Image

Hard disk sentinel

Image

Crystal disk info

Image

Image

SSD life

Image

PassMarkDiskCheckup

Image

Read test in HD tune

Image

Crystal disk mark 6

Image

Should I be worried?


Top
 Profile  
 
 Post subject: Re: Is everything good with my SSD??
PostPosted: November 9th, 2017, 23:52 
Offline
User avatar

Joined: September 8th, 2009, 18:21
Posts: 15440
Location: Australia
"Active hard disk monitor" doesn't understand the counterintuitive SMART data. I would ignore it. The raw error rate data are sector counts, not error counts. The actual error rate is 0, which corresponds to a maximum normalised value of 120.

SMART Attribute Details - Kingston:
https://media.kingston.com/support/downloads/MKP_306_SMART_attribute.pdf

_________________
A backup a day keeps DR away.


Top
 Profile  
 
 Post subject: Re: Is everything good with my SSD??
PostPosted: November 10th, 2017, 4:08 
Offline
User avatar

Joined: August 15th, 2006, 3:01
Posts: 3459
Location: CDRLabs @ Chandigarh [ India ]
fzabkar wrote:
"Active hard disk monitor" doesn't understand the counterintuitive SMART data. I would ignore it. The raw error rate data are sector counts, not error counts. The actual error rate is 0, which corresponds to a maximum normalised value of 120.

SMART Attribute Details - Kingston:
https://media.kingston.com/support/downloads/MKP_306_SMART_attribute.pdf



Well,
Frank is Saying That Your Kingston Has The Following Smart Attribs As Documented ,Any Software That Does Not Take That Into Consideration Will Give Wrong Data .

_________________
Regards
Amarbir S Dhillon , Chandigarh Data Recovery Labs [India]
Logical,Semi Physical And Physical Data Recovery
Website-> http://www.chandigarhdatarecovery.com


Top
 Profile  
 
 Post subject: Re: Is everything good with my SSD??
PostPosted: November 10th, 2017, 15:28 
Offline

Joined: November 9th, 2017, 15:37
Posts: 3
Location: Europe
Good to hear that everything is fine :D

I don`t understood that for raw rad error rate in manual for SMART, I am not an expert. That raw read error rate, will it go higher with SSD years?


Top
 Profile  
 
 Post subject: Re: Is everything good with my SSD??
PostPosted: November 10th, 2017, 15:46 
Offline
User avatar

Joined: September 8th, 2009, 18:21
Posts: 15440
Location: Australia
The drive reads 250 million sectors and records the number of read errors. The lower 32 bits of the raw field represent the sector count. Therefore, this number will increase until it hits 250 million, and then it will roll over to 0 and start increasing again. That's normal.

_________________
A backup a day keeps DR away.


Top
 Profile  
 
 Post subject: Re: Is everything good with my SSD??
PostPosted: November 11th, 2017, 11:42 
Offline

Joined: November 9th, 2017, 15:37
Posts: 3
Location: Europe
Ok, thank you 8)


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 6 posts ] 

All times are UTC - 5 hours [ DST ]


Who is online

Users browsing this forum: Google [Bot] and 12 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group