All times are UTC - 5 hours [ DST ]




Post new topic Reply to topic  [ 7 posts ] 
Author Message
 Post subject: broken usb key
PostPosted: February 14th, 2018, 16:20 
Offline

Joined: August 3rd, 2012, 7:47
Posts: 394
Location: slovenija
Hello,

where to solder wires and what to care on this broken USB key

thank you


Attachments:
IMG_0365.jpg
IMG_0365.jpg [ 740.73 KiB | Viewed 5889 times ]
IMG_0364.jpg
IMG_0364.jpg [ 655.64 KiB | Viewed 5889 times ]
Top
 Profile  
 
 Post subject: Re: broken usb key
PostPosted: February 14th, 2018, 18:07 
Offline

Joined: October 24th, 2009, 15:22
Posts: 872
Location: Poland
Take microscope and some wires and solder. It is really simple job, you can see where should be soldered. There is only one possibility fit connector to board.

_________________
Flash Killer - everyday new resources (pinout, XOR, ECC,config) for flash devices


Top
 Profile  
 
 Post subject: Re: broken usb key
PostPosted: February 14th, 2018, 19:06 
Offline
User avatar

Joined: September 8th, 2009, 18:21
Posts: 15463
Location: Australia
Look more closely.


Attachments:
pinout.jpg
pinout.jpg [ 151.2 KiB | Viewed 5859 times ]
correct_orientation.jpg
correct_orientation.jpg [ 298.06 KiB | Viewed 5859 times ]

_________________
A backup a day keeps DR away.
Top
 Profile  
 
 Post subject: Re: broken usb key
PostPosted: February 15th, 2018, 15:24 
Offline

Joined: August 3rd, 2012, 7:47
Posts: 394
Location: slovenija
thanko you Arvika and Mr. Zabkar for quick replay
I'm asking, because there is no coper on data + and data - to solder and also one trace nerar data + 242 is in the air

where to solder data+ and data-

thank you


Top
 Profile  
 
 Post subject: Re: broken usb key
PostPosted: February 15th, 2018, 17:18 
Offline

Joined: October 16th, 2013, 13:21
Posts: 713
Location: Brazil
Follow what remains from the traces in Data+ and Data-, see where they go, and solder in that place.
It seems they go to the other side of the 242 resistors, but you need to inspect it with a good microscope.


Top
 Profile  
 
 Post subject: Re: broken usb key
PostPosted: February 15th, 2018, 23:23 
Offline

Joined: December 8th, 2010, 11:37
Posts: 738
Location: Ottawa, Canada
Just lift that capacitor to see where the traces go and solder to it. Yeah, a microscope of even high powered magnifier will be helpful.

_________________
Sabo Computer Repairs & Data Recovery


Top
 Profile  
 
 Post subject: Re: broken usb key
PostPosted: February 15th, 2018, 23:55 
Offline
User avatar

Joined: December 4th, 2012, 1:35
Posts: 3844
Location: Adelaide, Australia
Larry means lift the crystal oscillator. I wouldnt, though, as the metal wires that go inside pull out easy. the blue marks are where the circuit traces are. You should magnify around 5x or 10x better and scrape off the green PCB coating with a hobby knife. you then solder 4 thin wires between the USB header and the circuit board. Do not solder to the middle resistors unless you confirm under magnification that the data traces go there.

It is pretty easy to do, but you must be extremely careful if you dont have much experience. If you dont magnify it, you probably will get solder where it doesnt belong and hinder recovery.

Attachment:
connect.jpg
connect.jpg [ 94.77 KiB | Viewed 5709 times ]


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 7 posts ] 

All times are UTC - 5 hours [ DST ]


Who is online

Users browsing this forum: No registered users and 42 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group