HDD GURU FORUMS http://forum.hddguru.com/ |
|
ST500DM002 Terminal Problem http://forum.hddguru.com/viewtopic.php?f=11&t=36479 |
Page 1 of 1 |
Author: | datarikaviri [ February 26th, 2018, 2:00 ] |
Post subject: | ST500DM002 Terminal Problem |
Hello everybody I have a case Seagate ST500DM002 drive. It can spin up, producing some unusual sounds while initializing (not head clicking) and stays at BSY state, no ID no service area access. And this is terminal output: Code: Boot 0x10M Spin Up[0x00000000][0x0000BA10] Trans. Rst 0x10M MC Internal LPC Process Spin Up FAIL Op=0900 Resp=0005 (P) SATA Reset MCMainPOR: Start: Check MCMT Version: Current MCMainPOR: Non-Init Case MC Seg Disc and Cache Nodes: 060DA288 060D8574 Seg Write Preamble VBM start: 00000D3C end: 00000D63 Footer - start: 00000D65 end: 00000D8C Seg Read Preamble VBM - start: 00000D8E end: 00000DB5 Footer - start: 00000DB7 end: 00000DDE Reconstruction: MCMT Reconstruction Start Max number of MC segments 22E0 Nonvolatile MCMT sequence number 00008FAF [RSRS] 193E ProcessRWError -Read- at LBA 000DCEC6 Sense Code=40000087 ProcessRWError -Read- at LBA 000DCEC7 Sense Code=40000087 FAIL Op=008F Resp=0003 FAIL Op=0155 Resp=0005 FAIL Op=008F Resp=0003 FAIL Op=0155 Resp=0005 FAIL Op=008F Resp=0003 FAIL Op=0155 Resp=0005 FAIL Op=008F Resp=0003 FAIL Op=0155 Resp=0005 InitiateMarkPendingReallocateRequest for disc_lba: 000DCEC7! Reconstruction: Completed 1: [MCMTWS] MCMainPOR: MCTBufferPtr->Header.MCStateFlagsDisc = 00000041 MCMainPOR: MCTBufferPtr->Header.MCTStateFlags = 0000002A MCMainPOR: MCStateFlags = 00000041 MCMainPOR: Feature Enabled... Starting LBA of RW Request=001320D3 Length=0000014C ProcessRWError -Read- at LBA 001320D9 Sense Code=43110081 Starting LBA of RW Request=001320D3 Length=0000014C ProcessRWError -Read- at LBA 00132175 Sense Code=43110081 RTL exceeded ProcessRWError -Read- at LBA 00132177 Sense Code=40000087 FAIL Op=008F Resp=0003 FAIL Op=0055 Resp=0005 FAIL Op=008F Resp=0003 FAIL Op=0055 Resp=0005 RTL exceeded ProcessRWError -Read- at LBA 0013217C Sense Code=40000087 RTL exceeded ProcessRWError -Read- at LBA 0013217F Sense Code=40000087 FAIL Op=008F Resp=0003 FAIL Op=0055 Resp=0005 FAIL Op=008F Resp=0003 FAIL Op=0055 Resp=0005 RTL exceeded Starting LBA of RW Request=00132183 Length=0000009C ProcessRWError -Read- at LBA 00132184 Sense Code=43110081 RTL exceeded FAIL Op=008F Resp=0003 FAIL Op=0065 Resp=0005 FAIL Op=008F Resp=0003 When I talk to ACELAB technical support he said try short circuit reading bus line and try to reach terminal but it didn't work. I can not work with terminal. Does anybody have any knowledge or advice for this situation? Thank you.. |
Author: | datarikaviri [ March 2nd, 2018, 1:33 ] |
Post subject: | Re: ST500DM002 Terminal Problem |
Any ideas ? |
Author: | hamidbid [ March 11th, 2018, 6:26 ] |
Post subject: | Re: ST500DM002 Terminal Problem |
you can change PCB and also you can test your HDD head (change head map in Rom) maybe some of your head was failed |
Author: | datarikaviri [ March 14th, 2018, 5:07 ] |
Post subject: | Re: ST500DM002 Terminal Problem |
Thank you for your interest hamidbid. I have tried PCB changing and head replacement but it didnt work anyway. When I try to short circuit read channel and try to reach terminal this is the output Code: ... ... F3 T> FAIL Op=0165 Resp=0005 ASCII Diag mode F3 T> FAIL Op=0065 Resp=0005 FAIL Op=0055 Resp=0005 FAIL Op=0055 Resp=0005 ASCII Diag mode F3 T> FAIL Op=0155 Resp=0005 FAIL Op=0155 Resp=0005 ASCII Diag mode F3 T> FAIL Op=0155 Resp=0005 FAIL Op=0155 Resp=0005 ASCII Diag mode F3 T> FAIL Op=0055 Resp=0005 FAIL Op=0055 Resp=0005 PASS FAIL Op=0165 Resp=0005 FAIL Op=0055 Resp=0005 FAIL Op=0165 Resp=0005 FAIL Op=0055 Resp=0005 Starting LBA of RW Request=001320E8 Length=0000014C ProcessRWError -Read- at LBA 00132189 Sense Code=43110081 RTL exceeded Starting LBA of RW Request=0013218C Length=000000A8 ProcessRWError -Read- at LBA 0013218C Sense Code=C3160080 FAIL Op=008F Resp=0003 FAIL Op=0055 Resp=0005 FAIL Op=008F Resp=0003 FAIL Op=0055 Resp=0005 LED:000000BD FAddr:00008A23 It is giving errors again after terminal access (F3 T>). Do you have any other idea what can I do for this case?? |
Author: | hamidbid [ March 17th, 2018, 4:42 ] |
Post subject: | Re: ST500DM002 Terminal Problem |
you should hold short point for 5 and sometimes 10 minutes to access to terminal |
Page 1 of 1 | All times are UTC - 5 hours [ DST ] |
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |