HDD GURU FORUMS http://forum.hddguru.com/ |
|
recover refurbished drive OOS3000G or tp3000GB http://forum.hddguru.com/viewtopic.php?f=11&t=38069 |
Page 1 of 1 |
Author: | hamidbid [ February 14th, 2019, 2:52 ] |
Post subject: | recover refurbished drive OOS3000G or tp3000GB |
Hi to all newly, arrived a refurbished hdd seagete 3 tb that i think some heads are weak so i want use head map but i can access to service area Hdd detect Model : OOS3000G Serial : 00000000 Firmware : ZZZZFFFF Capacity : 3 TB (5 860 533 168) in log Family ID by HDD ID: 58 Selected family......................... : 58, Grenada Model by ID............................. : OOS3000G Loading default settings! Use the options dialog to review and save utility settings. Then press OK! Family default settings loading! Tech Key... En Tech err! Tech state 0xFF, 0xFF010000 Detecting SA Phys Sct Size... Can not detect SA phys secotr size by terminal! in terminal Family ID by HDD ID: 58 Selected family......................... : 58, Grenada Model by ID............................. : OOS3000G Loading default settings! Use the options dialog to review and save utility settings. Then press OK! Family default settings loading! Tech Key... En Tech err! Tech state 0xFF, 0xFF010000 Detecting SA Phys Sct Size... Can not detect SA phys secotr size by terminal! In terminal UNLOCK ERROR! Spin Up SpinOK TCC:001B (P) SATA Reset ASCII Diag mode After ctrl +L F3 T> Overlay PartNum: 10060942 CFW PartNum: 05272014 Overlay CompileDate: 20131006 CFW CompileDate: 20140527 OverlayCompatibilityCheck failed Unable to load Diag Cmd Processor Overlay some command works V1,V2,... but other command not worked |
Author: | hamidbid [ February 14th, 2019, 3:05 ] | ||
Post subject: | Re: recover refurbished drive OOS3000G or tp3000GB | ||
after search below link similar my problem https://forum.acelaboratory.com/viewtopic.php?t=9668 also i tried read terminal but end with error again Thanks for any idea
|
Author: | E123 [ February 14th, 2019, 9:25 ] |
Post subject: | Re: recover refurbished drive OOS3000G or tp3000GB |
hamidbid Can I see it's ROM? Interesting case. Someone load an incompatible loader into it. There is a small collection. And from refarb too. Maybe something will be selected. |
Author: | hamidbid [ February 14th, 2019, 12:39 ] | ||
Post subject: | Re: recover refurbished drive OOS3000G or tp3000GB | ||
E123 wrote: hamidbid Can I see it's ROM? Interesting case. Someone load an incompatible loader into it. There is a small collection. And from refarb too. Maybe something will be selected. Hi E123 yes I think so
|
Author: | E123 [ February 14th, 2019, 15:27 ] |
Post subject: | Re: recover refurbished drive OOS3000G or tp3000GB |
Unfortunately, I do not have a loader compatible with this ROM and there is no ROM under the overlays 2013.10.06. I can only suggest that the prototype was ST3000DM001-1CH166-899. So there is no need for an unlock. It is only necessary to make compatible ROM and overlays. In this case, I can only offer a risky solution from myself: put an available seagate updateer under 1CH166 into the disk. I have version CC29. |
Author: | hamidbid [ February 16th, 2019, 2:28 ] |
Post subject: | Re: recover refurbished drive OOS3000G or tp3000GB |
E123 wrote: Unfortunately, I do not have a loader compatible with this ROM and there is no ROM under the overlays 2013.10.06. I can only suggest that the prototype was ST3000DM001-1CH166-899. So there is no need for an unlock. It is only necessary to make compatible ROM and overlays. In this case, I can only offer a risky solution from myself: put an available seagate updateer under 1CH166 into the disk. I have version CC29. Thanks for answer I never have updated fw then I don't know what happen for hard disk maybe some sections in Rom and Service Area ? is this reversible ? I have another Rom with another part number ? is this useful |
Author: | data-medics [ February 16th, 2019, 8:14 ] |
Post subject: | Re: recover refurbished drive OOS3000G or tp3000GB |
If you have LBA access already and terminal access, then I wouldn't bother with trying to update the firmware or anything like that. You can read system file 93 by just using y-modem and the T>r93 command. Turn off all the stuff in the SAP control flags menu, then write it back using the T>w93 command and y-modem. If for some reason that doesn't work, you can still turn off most of those functions using the F command in terminal manually. It's a bit more complex to explain how to do that, but it should work. Just shoot me a PM if you need help. I don't mind doing a remote session sometime next week. That should resolve the speed issues. |
Author: | hamidbid [ February 18th, 2019, 4:05 ] |
Post subject: | Re: recover refurbished drive OOS3000G or tp3000GB |
data-medics wrote: If you have LBA access already and terminal access, then I wouldn't bother with trying to update the firmware or anything like that. You can read system file 93 by just using y-modem and the T>r93 command. Turn off all the stuff in the SAP control flags menu, then write it back using the T>w93 command and y-modem. If for some reason that doesn't work, you can still turn off most of those functions using the F command in terminal manually. It's a bit more complex to explain how to do that, but it should work. Just shoot me a PM if you need help. I don't mind doing a remote session sometime next week. That should resolve the speed issues. Thanks for Answer, F3 T>r HighPowerMode Status 0001 Req 0002 Overlay PartNum: 10060942 CFW PartNum: 05272014 Overlay CompileDate: 20131006 CFW CompileDate: 20140527 OverlayCompatibilityCheck failed Unable to load Diag Cmd Processor Overlay F3 T>F Overlay PartNum: 10060942 CFW PartNum: 05272014 Overlay CompileDate: 20131006 CFW CompileDate: 20140527 OverlayCompatibilityCheck failed Unable to load Diag Cmd Processor Overlay F3 T>F,,22 Overlay PartNum: 10060942 CFW PartNum: 05272014 Overlay CompileDate: 20131006 CFW CompileDate: 20140527 OverlayCompatibilityCheck failed Unable to load Diag Cmd Processor Overlay It 's not accept This commands in terminal , I don't think it's different with any other terminal program hdd firmware ignore any special command some commands are working such as V in T level or 7>x but 7>X not working I'll be happy for your help?thanks again |
Author: | hamidbid [ February 18th, 2019, 4:27 ] |
Post subject: | Re: recover refurbished drive OOS3000G or tp3000GB |
I 'm very appreciate for your information I learn very useful information about Rom http://www.hddoracle.com/viewtopic.php? ... ab45c44c89 |
Author: | hamidbid [ February 18th, 2019, 7:38 ] | ||
Post subject: | Re: recover refurbished drive OOS3000G or tp3000GB | ||
I analyzed my refer Rom in container segment ID 22 000100 ----030000 at both section in Rom (000000-3FFFF,40000-7FFFF) I found 16 000040 BootFW-DIR 15 000048 General Data 0E 000248 IAP 10 000658 BootFW 03 018000 SFW 0B 02E000 Shell 00 02F100 end container Interesting , all data in segments at two section are the same attached all segments
|
Author: | E123 [ February 18th, 2019, 8:09 ] |
Post subject: | Re: recover refurbished drive OOS3000G or tp3000GB |
You are in the wrong direction headed. If you so want to learn ROM, then here is the F3romExplorer tool https://yadi.sk/d/SpRqMHhE3Vqkvq And if you do not have access to the UA, then look for a way to fill compatible overlays. I gave you an updater. And here is another, LodEdit utility: https://yadi.sk/d/ps0J3Kns3A3KY9 You can disassemble the updater and with the F3romExplorer collect the image CC29 from your own ROM. Then the updater will be a LOADER for your CC29. |
Author: | hamidbid [ February 18th, 2019, 8:20 ] | ||
Post subject: | Re: recover refurbished drive OOS3000G or tp3000GB | ||
and data in segment General Data is 27.5.2014 I think ,maybe I should find another Rom for 3 tb Grenada family and compare them with my refer to find appropriate fw also I attached CAP,SAP,RAP my Rom
|
Author: | hamidbid [ February 18th, 2019, 8:30 ] |
Post subject: | Re: recover refurbished drive OOS3000G or tp3000GB |
E123 wrote: You are in the wrong direction headed. If you so want to learn ROM, then here is the F3romExplorer tool https://yadi.sk/d/SpRqMHhE3Vqkvq And if you do not have access to the UA, then look for a way to fill compatible overlays. I gave you an updater. And here is another, LodEdit utility: https://yadi.sk/d/ps0J3Kns3A3KY9 You can disassemble the updater and with the F3romExplorer collect the image CC29 from your own ROM. Then the updater will be a LOADER for your CC29. Hi E123 very thanks for share files sure , i'm going to work on and then left message |
Author: | E123 [ February 18th, 2019, 8:44 ] |
Post subject: | Re: recover refurbished drive OOS3000G or tp3000GB |
ROM CC29 + loader https://yadi.sk/d/9FTMofTK-xE7hw |
Author: | hamidbid [ February 25th, 2019, 2:45 ] | ||
Post subject: | Re: recover refurbished drive OOS3000G or tp3000GB | ||
E123 wrote: ROM CC29 + loader https://yadi.sk/d/9FTMofTK-xE7hw The first , I admire you for useful utility I learn a lot The second Thanks for rebuild Rom and loader I wrote Rom with terminal after power on got this message in terminal Boot 0x40M Spin Up Trans. Disc FW failed to load after that I used from loader it didn't worked again wrote refer Rom to Pcb but again got the same message I changed PCB but again the same message!!? what happened for Hard disk? How can I do?
|
Author: | hamidbid [ February 25th, 2019, 3:02 ] |
Post subject: | Re: recover refurbished drive OOS3000G or tp3000GB |
E123 wrote: Unfortunately, I do not have a loader compatible with this ROM and there is no ROM under the overlays 2013.10.06. I can only suggest that the prototype was ST3000DM001-1CH166-899. So there is no need for an unlock. It is only necessary to make compatible ROM and overlays. In this case, I can only offer a risky solution from myself: put an available seagate updateer under 1CH166 into the disk. I have version CC29. I 'm a little confuse what's date of 2013.10.06. ? How do you find this date while my data Rom is 2014.27.05? and In last How do I load a loader in Grenada family? I'm so sorry for many questions? |
Author: | E123 [ February 26th, 2019, 6:35 ] |
Post subject: | Re: recover refurbished drive OOS3000G or tp3000GB |
In your screenshot, the disk has readiness in the ATA registers. Download CC29 loader by ATA. If the ABRT or ERR fails to appear in the registers, use the module "CFW_DISK" from the CC29 loader. This is your 3D loader for MRT. Use the virtual load in MRT. For dates: do not pay attention. This is me for myself - to identify different versions of the same firmware. |
Author: | E123 [ February 26th, 2019, 9:00 ] |
Post subject: | Re: recover refurbished drive OOS3000G or tp3000GB |
Sorry, stupid.))) Of course, not an MRT, but PC3K. But the meaning is the same, only the names are different. |
Author: | hamidbid [ March 2nd, 2019, 4:14 ] |
Post subject: | Re: recover refurbished drive OOS3000G or tp3000GB |
E123 wrote: In your screenshot, the disk has readiness in the ATA registers. Download CC29 loader by ATA. If the ABRT or ERR fails to appear in the registers, use the module "CFW_DISK" from the CC29 loader. This is your 3D loader for MRT. Use the virtual load in MRT. For dates: do not pay attention. This is me for myself - to identify different versions of the same firmware. Hi E123 A million Thanks for your response, after play with loader and cfw-disk finally, I could access to sa and backup from that and built head map ,disabled smp flag IN continue I tested with another Rom( CC44) and loader (with cfwdisk) and could upgrade fw (from cc29 to cc44) and in deeper search , I copied sysfile 20D to 20E after power off/on Wow hard detect in normal mode .... again I am really appreciate from E123 and Frank for great help in http://www.hddoracle.com/viewtopic.php?f=59&t=2173 |
Page 1 of 1 | All times are UTC - 5 hours [ DST ] |
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |