All times are UTC - 5 hours [ DST ]


Forum rules


Please do not post questions about data recovery cases here (use this forum instead). This forum is for topics on finding new ways to recover data. Accessing firmware, writing programs, reading bits off the platter, recovering data from dust...



Post new topic Reply to topic  [ 10 posts ] 
Author Message
 Post subject: STM31000528AS Clicking Noise
PostPosted: March 9th, 2013, 10:59 
Offline

Joined: March 9th, 2013, 10:52
Posts: 4
Location: tehran
i don't know whats happen my hard working well but after restart make click noise and not detect STM31000528AS

100% new hard


Top
 Profile  
 
 Post subject: Re: STM31000528AS Clicking Noise
PostPosted: March 9th, 2013, 13:43 
Offline

Joined: March 9th, 2013, 10:52
Posts: 4
Location: tehran
i want to repair this and i dont want data

and i have dku-5 cable for hyperterminal repairing


Top
 Profile  
 
 Post subject: Re: STM31000528AS Clicking Noise
PostPosted: March 22nd, 2013, 15:50 
Offline

Joined: March 9th, 2013, 10:52
Posts: 4
Location: tehran
OK Fine :

Rst 0x20M
Servo Processor Is Reset.
RW: Disc Ctlr Initialization Completed.

ExecuteSpinRequest
[Clicking]
ASCII Diag mode

F3 T>/2

F3 2>Z

No HOST FIS-ReadyStatusFlags 2002B001
DiagError 00005014
F3 2>U

DiagError 00005014
F3 2>/

F3 T>F,,22
[Clicking]
ExecuteSpinRequest

HighPowerMode
Failed to load overlay 00000004
LED:000000CC FAddr:00289705
LED:000000CC FAddr:00289705
LED:000000CC FAddr:00289705
LED:000000CC FAddr:00289705
LED:000000CC FAddr:00289705
LED:000000CC FAddr:00289705
LED:000000CC FAddr:00289705
LED:000000CC FAddr:00289705
...


Top
 Profile  
 
 Post subject: Re: STM31000528AS Clicking Noise
PostPosted: March 22nd, 2013, 15:54 
Offline

Joined: March 9th, 2013, 10:52
Posts: 4
Location: tehran
Again (With Plastic Under Motor Power) :

Rst 0x20M
Servo Processor Is Reset.
RW: Disc Ctlr Initialization Completed.

ExecuteSpinRequest

ASCII Diag mode

F3 T>/2

F3 2>
No HOST FIS-ReadyStatusFlags 2002B001

F3 2>Z

HighPowerMode
Spin Down Complete
Elapsed Time 0.084 msecs
F3 2>U

HighPowerMode
ExecuteSpinRequest
[Clicking]
DiagError 00006008
Spin Error
Elapsed Time 22.640 secs
R/W Status 2 R/W Error 84150180
F3 2>/

F3 T>F,,22

Failed to load overlay 00000004
LED:000000CC FAddr:00289705
LED:000000CC FAddr:00289705
LED:000000CC FAddr:00289705
LED:000000CC FAddr:00289705
LED:000000CC FAddr:00289705
LED:000000CC FAddr:00289705
LED:000000CC FAddr:00289705
LED:000000CC FAddr:00289705
...


Top
 Profile  
 
 Post subject: Re: STM31000528AS Clicking Noise
PostPosted: March 28th, 2013, 8:04 
Offline

Joined: March 21st, 2013, 14:45
Posts: 121
Location: India
erfanoabdi wrote:
OK Fine :

Rst 0x20M
Servo Processor Is Reset.
RW: Disc Ctlr Initialization Completed.

ExecuteSpinRequest
[Clicking]
ASCII Diag mode

F3 T>/2

F3 2>Z

No HOST FIS-ReadyStatusFlags 2002B001
DiagError 00005014
F3 2>U

DiagError 00005014
F3 2>/

F3 T>F,,22
[Clicking]
ExecuteSpinRequest

HighPowerMode
Failed to load overlay 00000004
LED:000000CC FAddr:00289705
LED:000000CC FAddr:00289705
LED:000000CC FAddr:00289705
LED:000000CC FAddr:00289705
LED:000000CC FAddr:00289705
LED:000000CC FAddr:00289705
LED:000000CC FAddr:00289705
LED:000000CC FAddr:00289705
...


Hi Dear Friend erfanoabdi

This Is Not Normal Common Problem If The Data Is Need Then Dont Do Anything Urself Tell Here Where R U From Full Location So If Some We Can Give Good Suggetion.
I Have Solution But Its Not Easy DIY.
Sorry For My Bad English.

Yours Friend
Jignesh Pankhania (India/Gujarat/Ahmedabad)


Top
 Profile  
 
 Post subject: Re: STM31000528AS Clicking Noise
PostPosted: March 28th, 2013, 8:47 
Offline

Joined: August 18th, 2010, 17:35
Posts: 3636
Location: Massachusetts, USA
Joined: March 9th, 2013, 10:52
Posts: 4
Location: tehran

_________________
Hard Disk Drive, SSD, USB Drive and RAID Data Recovery Specialist in Massachusetts


Top
 Profile  
 
 Post subject: Re: STM31000528AS Clicking Noise
PostPosted: April 23rd, 2013, 0:27 
Offline

Joined: April 18th, 2013, 7:05
Posts: 56
Location: Somewhere Out There
its been a month he didnt reply..guess where could he have been ? :lol:


Top
 Profile  
 
 Post subject: Re: STM31000528AS Clicking Noise
PostPosted: October 6th, 2017, 20:25 
Offline

Banned User

Joined: May 11th, 2017, 17:10
Posts: 236
Location: Iran
erfanoabdi wrote:
OK Fine :

Rst 0x20M
Servo Processor Is Reset.
RW: Disc Ctlr Initialization Completed.

ExecuteSpinRequest
[Clicking]
ASCII Diag mode

F3 T>/2

F3 2>Z

No HOST FIS-ReadyStatusFlags 2002B001
DiagError 00005014
F3 2>U

DiagError 00005014
F3 2>/

F3 T>F,,22
[Clicking]
ExecuteSpinRequest

HighPowerMode
Failed to load overlay 00000004
LED:000000CC FAddr:00289705
LED:000000CC FAddr:00289705
LED:000000CC FAddr:00289705
LED:000000CC FAddr:00289705
LED:000000CC FAddr:00289705
LED:000000CC FAddr:00289705
LED:000000CC FAddr:00289705
LED:000000CC FAddr:00289705
...


head is gone and damaged
you can only use pcb as donor

_________________
Mohammad Mazaheri

Email: mazaheri.online@gmail.com

Mobile: +989185005214


Top
 Profile  
 
 Post subject: Re: STM31000528AS Clicking Noise
PostPosted: October 7th, 2017, 16:42 
Offline
User avatar

Joined: December 8th, 2013, 4:48
Posts: 831
Location: Pakistan
yes sometime people just post in passion and dont realize how old is the post ...

_________________
Data Recovery Pakistan


Top
 Profile  
 
 Post subject: Re: STM31000528AS Clicking Noise
PostPosted: November 30th, 2017, 19:31 
Offline

Joined: October 3rd, 2005, 0:40
Posts: 4301
Location: Hungary
i just wonder how the hack they find these stone-age topics...

_________________
Adatmentés - Data recovery


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 10 posts ] 

All times are UTC - 5 hours [ DST ]


Who is online

Users browsing this forum: No registered users and 5 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group