HDD GURU FORUMS http://forum.hddguru.com/ |
|
What next? http://forum.hddguru.com/viewtopic.php?f=26&t=27114 |
Page 2 of 2 |
Author: | northwind [ November 29th, 2013, 8:52 ] |
Post subject: | Re: What next? |
WD Black ramp set 2.5" and 3.5" ? (the ones that hold the HSA with a screw on the bottom) |
Author: | helpdisc [ December 9th, 2013, 16:36 ] |
Post subject: | Re: What next? |
we are finishing hitachi 3.5 then we will make 2.5 also hitachi. Then Wd black Ramp set and then toshiba F'haristo Dimitry |
Author: | Doomer [ December 9th, 2013, 19:15 ] |
Post subject: | Re: What next? |
helpdisc wrote: precise and plastic do not go in same sentence. best you can get with plastic moulds is 1/10 of a mm. For tool to be good you need 100 times more precise tehnology. Problems accure if messurments are in +/- 2/100 of a mm. Imposibile to do it in plastic and to be good enogh. Manufacturers make shipping combs from plastic, that's a fact, so I guess it's precise enough. Did you check the link I posted? |
Author: | helpdisc [ December 10th, 2013, 4:02 ] |
Post subject: | Re: What next? |
for us it was not precise enough. We are not assembling it we need to disassemble it first. Moulds it self cost a loooot to be made and ones we tried did not gave results we needed. |
Author: | HaQue [ December 10th, 2013, 4:45 ] |
Post subject: | Re: What next? |
helpdisc wrote: for us it was not precise enough. We are not assembling it we need to disassemble it first. Moulds it self cost a loooot to be made and ones we tried did not gave results we needed. Yes I found that out back in the day when I was enquiring about getting Spindle Clamps made up for the CD Drives of the Playstation. I was getting a couple a week to fix and the spares were expensive. But as I was in the stages of locating designers and mould makers, some aspiring online seller beat me to it. I was gonna make meeeelyons! |
Author: | scratchy [ April 8th, 2014, 18:18 ] |
Post subject: | Re: What next? |
Samsung 2.5 |
Author: | northwind [ May 17th, 2014, 3:55 ] |
Post subject: | Re: What next? |
scratchy wrote: Samsung 2.5 +1 |
Author: | continuum [ September 25th, 2014, 22:23 ] |
Post subject: | Re: What next? |
Something to unstick the heads of a ramped wd passport that has been dropped. I cannot for the life of me find a way to get them back onto the ramp when they are knocked off without damaging them. Also, paypal would be great. I know I have mentioned this to you, but I would be more than happy to pay the extra 2.9% |
Author: | zarko_hddsurgery [ September 30th, 2014, 7:55 ] |
Post subject: | Re: What next? |
About PayPal, it was introduced in Serbia some time ago however we still can use it for paying only, not for receiving payments. Our government announced that receiving payment via PayPal will be available soon, so we can only wait and try to believe the politicians. |
Author: | labtech [ September 30th, 2014, 8:52 ] |
Post subject: | Re: What next? |
zarko_hddsurgery wrote: About PayPal...so we can only wait and try to believe the politicians. Hahhaaaahaa, just like the brothers across the Danube to the north east. Seems like epidemic in our area. What model WD is the drive in the pic, please? Thanks |
Author: | zarko_hddsurgery [ October 1st, 2014, 8:32 ] |
Post subject: | Re: What next? |
labtech wrote: zarko_hddsurgery wrote: About PayPal...so we can only wait and try to believe the politicians. Hahhaaaahaa, just like the brothers across the Danube to the north east. Seems like epidemic in our area. What model WD is the drive in the pic, please? Thanks Hahhaha I think that politicians are the same everywhere, not only in our region. I think it's WD2500BEVT-00ZCT0. Not sure, because the lid is lost somewhere. |
Author: | northwind [ October 1st, 2014, 9:09 ] |
Post subject: | Re: What next? |
zarko_hddsurgery wrote: I think it's WD2500BEVT-00ZCT0. Not sure, because the lid is lost somewhere. Is it recoverable? |
Author: | labtech [ October 2nd, 2014, 7:47 ] |
Post subject: | Re: What next? |
I see...thanks. yes, ZCTs can be tough suckers. |
Page 2 of 2 | All times are UTC - 5 hours [ DST ] |
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |