All times are UTC - 5 hours [ DST ]




Post new topic Reply to topic  [ 40 posts ]  Go to page 1, 2  Next
Author Message
 Post subject: New NAND ID " 983E980376E4081E " With PS2251-19-26 CTRL
PostPosted: July 25th, 2023, 0:35 
Offline
User avatar

Joined: August 15th, 2006, 3:01
Posts: 3464
Location: CDRLabs @ Chandigarh [ India ]
Hi Friends ,
Anyone Worked On This NAND ID Earlier ,Also Anyone Worked On PS2251-19-26 Controller In VNR With Results ,The PS2251-19 Details Are Here - > https://www.phison.com/en/solutions/con ... ovable/usb .This Is From a Kingston DataTraveler Exodia M With 64GB Capacity -> https://www.kingston.com/en/usb-flash-drives

Toshiba NAND : 983E980376E4081E

_________________
Regards
Amarbir S Dhillon , Chandigarh Data Recovery Labs [India]
Logical,Semi Physical And Physical Data Recovery
Website-> http://www.chandigarhdatarecovery.com


Top
 Profile  
 
 Post subject: Re: New NAND ID " 983E980376E4081E " With PS2251-19-26 CTRL
PostPosted: July 25th, 2023, 7:57 
Offline
User avatar

Joined: August 15th, 2006, 3:01
Posts: 3464
Location: CDRLabs @ Chandigarh [ India ]
Friends ,
Sharing Some Images of The Circuit Board

Attachment:
IMG_20230725_163603003~2.jpg
IMG_20230725_163603003~2.jpg [ 473.6 KiB | Viewed 4687 times ]

Attachment:
IMG_20230725_163610017~2.jpg
IMG_20230725_163610017~2.jpg [ 244.24 KiB | Viewed 4687 times ]

_________________
Regards
Amarbir S Dhillon , Chandigarh Data Recovery Labs [India]
Logical,Semi Physical And Physical Data Recovery
Website-> http://www.chandigarhdatarecovery.com


Top
 Profile  
 
 Post subject: Re: New NAND ID " 983E980376E4081E " With PS2251-19-26 CTRL
PostPosted: July 25th, 2023, 11:37 
Offline
User avatar

Joined: July 8th, 2019, 12:27
Posts: 147
Location: 中国大陆浙江省湖州市
The difficulty lies not only in correctly reading the chip, but reading the chip is the first step


Attachments:
983E980376E4_VNR.png
983E980376E4_VNR.png [ 61.72 KiB | Viewed 4668 times ]
983E980376E4Chip.txt [948 Bytes]
Downloaded 101 times

_________________
Auxiliary Tool Used For MonoLith Data Recovery, featuring the industry's most extensive Monolith pinouts
http://flash-matrix.com/
Top
 Profile  
 
 Post subject: Re: New NAND ID " 983E980376E4081E " With PS2251-19-26 CTRL
PostPosted: July 25th, 2023, 12:54 
Offline
User avatar

Joined: August 15th, 2006, 3:01
Posts: 3464
Location: CDRLabs @ Chandigarh [ India ]
csava wrote:
The difficulty lies not only in correctly reading the chip, but reading the chip is the first step


Well,
Did Not Work ,Something Is Wrong Somewhere ,Testing Voltages Tommorow In Office

Attachment:
1.png
1.png [ 1002.33 KiB | Viewed 4644 times ]

_________________
Regards
Amarbir S Dhillon , Chandigarh Data Recovery Labs [India]
Logical,Semi Physical And Physical Data Recovery
Website-> http://www.chandigarhdatarecovery.com


Top
 Profile  
 
 Post subject: Re: New NAND ID " 983E980376E4081E " With PS2251-19-26 CTRL
PostPosted: July 25th, 2023, 22:27 
Offline
User avatar

Joined: July 8th, 2019, 12:27
Posts: 147
Location: 中国大陆浙江省湖州市
Applicable to your case.Check 1, 2, 23, 24, 25, 26, 47, 48; they may have slight variations across different cases


Attachments:
new_tsop48_vccq&dqs.png
new_tsop48_vccq&dqs.png [ 59.1 KiB | Viewed 4595 times ]

_________________
Auxiliary Tool Used For MonoLith Data Recovery, featuring the industry's most extensive Monolith pinouts
http://flash-matrix.com/
Top
 Profile  
 
 Post subject: Re: New NAND ID " 983E980376E4081E " With PS2251-19-26 CTRL
PostPosted: July 29th, 2023, 10:35 
Offline
User avatar

Joined: August 15th, 2006, 3:01
Posts: 3464
Location: CDRLabs @ Chandigarh [ India ]
Hi ,
I have Measured The Pins ,I will post results when i reach Home .VCCQ is 1.2 Volts and The Rusolut Reader Does Not Support Less Then 1.6 Volts ,How Are We Able To Read such Chips Then .

_________________
Regards
Amarbir S Dhillon , Chandigarh Data Recovery Labs [India]
Logical,Semi Physical And Physical Data Recovery
Website-> http://www.chandigarhdatarecovery.com


Top
 Profile  
 
 Post subject: Re: New NAND ID " 983E980376E4081E " With PS2251-19-26 CTRL
PostPosted: July 30th, 2023, 0:37 
Offline
User avatar

Joined: July 8th, 2019, 12:27
Posts: 147
Location: 中国大陆浙江省湖州市
Amarbir[CDR-Labs] wrote:
Hi ,
I have Measured The Pins ,I will post results when i reach Home .VCCQ is 1.2 Volts and The Rusolut Reader Does Not Support Less Then 1.6 Volts ,How Are We Able To Read such Chips Then .

The chip can be read by VNR with VCC=3.3V and VCCQ=1.8V. I am using the adapter I designed, which aims to facilitate the replacement of voltage pins with special configurations. For the 3K, I have read the latest updates, and they have added this chip to the chip database. However, I haven't tested the software with this new addition yet. As for the FE, there were significant issues when reading low voltage chips with the existing hardware. But I have successfully addressed this problem by patch. You can find more information about it on my website.

_________________
Auxiliary Tool Used For MonoLith Data Recovery, featuring the industry's most extensive Monolith pinouts
http://flash-matrix.com/


Top
 Profile  
 
 Post subject: Re: New NAND ID " 983E980376E4081E " With PS2251-19-26 CTRL
PostPosted: July 30th, 2023, 1:28 
Offline
User avatar

Joined: August 15th, 2006, 3:01
Posts: 3464
Location: CDRLabs @ Chandigarh [ India ]
csava wrote:
Amarbir[CDR-Labs] wrote:
Hi ,
I have Measured The Pins ,I will post results when i reach Home .VCCQ is 1.2 Volts and The Rusolut Reader Does Not Support Less Then 1.6 Volts ,How Are We Able To Read such Chips Then .

The chip can be read by VNR with VCC=3.3V and VCCQ=1.8V. I am using the adapter I designed, which aims to facilitate the replacement of voltage pins with special configurations. For the 3K, I have read the latest updates, and they have added this chip to the chip database. However, I haven't tested the software with this new addition yet. As for the FE, there were significant issues when reading low voltage chips with the existing hardware. But I have successfully addressed this problem by patch. You can find more information about it on my website.


Hi,
The TS Team of rusolut had asked me to measure voltages when the NAND was removed on all pins of the PCB Also they had asked me to measure continuity of certain pins to specific pins

Attachment:
CDRLabs [India] - Voltages When NAND Was Removed.jpg
CDRLabs [India] - Voltages When NAND Was Removed.jpg [ 597.69 KiB | Viewed 4389 times ]

Attachment:
CDRLabs [India] - Specific Pins Continuity.jpg
CDRLabs [India] - Specific Pins Continuity.jpg [ 512.21 KiB | Viewed 4389 times ]

_________________
Regards
Amarbir S Dhillon , Chandigarh Data Recovery Labs [India]
Logical,Semi Physical And Physical Data Recovery
Website-> http://www.chandigarhdatarecovery.com


Top
 Profile  
 
 Post subject: Re: New NAND ID " 983E980376E4081E " With PS2251-19-26 CTRL
PostPosted: July 31st, 2023, 7:35 
Online

Joined: August 13th, 2016, 17:10
Posts: 193
Location: Vienna, Austria
I had an idea for the VCCQ of 1.2 Volts: You could try to use a Voltage divider made out of 2 resistors. Adding just 2 resistors should be a relatively easy modification for the adapters I guess.


Top
 Profile  
 
 Post subject: Re: New NAND ID " 983E980376E4081E " With PS2251-19-26 CTRL
PostPosted: July 31st, 2023, 16:32 
Offline

Joined: September 17th, 2016, 16:06
Posts: 430
Location: India
same chip id. Dump from a block . Page 01


Attachments:
File comment: Kingston Data Traveller Exodia
GoodBlock.png
GoodBlock.png [ 166.74 KiB | Viewed 4277 times ]
Top
 Profile  
 
 Post subject: Re: New NAND ID " 983E980376E4081E " With PS2251-19-26 CTRL
PostPosted: July 31st, 2023, 19:02 
Offline

Joined: September 17th, 2016, 16:06
Posts: 430
Location: India
Some decryption. Some Tables.
Good Night/Good Morning :)
--


Attachments:
some tables.png
some tables.png [ 298.9 KiB | Viewed 4264 times ]
Top
 Profile  
 
 Post subject: Re: New NAND ID " 983E980376E4081E " With PS2251-19-26 CTRL
PostPosted: July 31st, 2023, 19:09 
Offline
User avatar

Joined: September 8th, 2009, 18:21
Posts: 15461
Location: Australia
sourcerer wrote:
I had an idea for the VCCQ of 1.2 Volts: You could try to use a Voltage divider made out of 2 resistors. Adding just 2 resistors should be a relatively easy modification for the adapters I guess.

You cannot use a potential divider as a power source. As soon as you draw power from the divider, the voltage drops. Instead, you can add a 1.2V LDO regulator for $1.

_________________
A backup a day keeps DR away.


Top
 Profile  
 
 Post subject: Re: New NAND ID " 983E980376E4081E " With PS2251-19-26 CTRL
PostPosted: August 1st, 2023, 14:16 
Offline

Joined: September 17th, 2016, 16:06
Posts: 430
Location: India
Hello. I would say one can if one knew what is the load current of the VCCQ line

__________Vin
|
|
r1
|
|------>load current to vccq and node voltage required.
r2
|
|
Gnd

However I would stick to 2x emitter followers. :) Why spend even a 1$ :)

One should make sure that input current is always limited to a very low value and try not to fry the reader :)

PS
I could dexor my dump with same chip id. The controller is Innostor. I will give a shot with Exodia M series too... :)
--


Top
 Profile  
 
 Post subject: Re: New NAND ID " 983E980376E4081E " With PS2251-19-26 CTRL
PostPosted: August 1st, 2023, 20:17 
Offline

Joined: September 17th, 2016, 16:06
Posts: 430
Location: India
I think I am getting there :)

Loads to learn and explore. How would one go about "set features" || making custom file for RR || read sensitivity setting in VNR ?

--


Attachments:
not bad we are getting there.png
not bad we are getting there.png [ 225.13 KiB | Viewed 4158 times ]
Top
 Profile  
 
 Post subject: Re: New NAND ID " 983E980376E4081E " With PS2251-19-26 CTRL
PostPosted: August 2nd, 2023, 7:40 
Offline
User avatar

Joined: July 8th, 2019, 12:27
Posts: 147
Location: 中国大陆浙江省湖州市
sin wrote:
Hello. I would say one can if one knew what is the load current of the VCCQ line

__________Vin
|
|
r1
|
|------>load current to vccq and node voltage required.
r2
|
|
Gnd

However I would stick to 2x emitter followers. :) Why spend even a 1$ :)

One should make sure that input current is always limited to a very low value and try not to fry the reader :)

PS
I could dexor my dump with same chip id. The controller is Innostor. I will give a shot with Exodia M series too... :)
--

I believe this is an ideal model, but it is not applicable in practical circuits. This is because you have not considered the internal resistances of the I/O pins. The I/O pins are controlled by two N-MOSFETs, and you need to take into account the gate impedance

_________________
Auxiliary Tool Used For MonoLith Data Recovery, featuring the industry's most extensive Monolith pinouts
http://flash-matrix.com/


Top
 Profile  
 
 Post subject: Re: New NAND ID " 983E980376E4081E " With PS2251-19-26 CTRL
PostPosted: August 2nd, 2023, 7:46 
Offline

Joined: September 17th, 2016, 16:06
Posts: 430
Location: India
Very good input. Its surely a very basic idea. However please correct me. Isn't VCCQ a constant DC signal. Why would you consider impedances in that case?
Putting LDO surely does not seems considerate towards impedance either.


--


Top
 Profile  
 
 Post subject: Re: New NAND ID " 983E980376E4081E " With PS2251-19-26 CTRL
PostPosted: August 2nd, 2023, 7:48 
Offline
User avatar

Joined: July 8th, 2019, 12:27
Posts: 147
Location: 中国大陆浙江省湖州市
sin wrote:
I think I am getting there :)

Loads to learn and explore. How would one go about "set features" || making custom file for RR || read sensitivity setting in VNR ?

--

I've been searching for such an option all along, but unfortunately, I only found something similar in the software dialog box of the chip. However, that's not the option I'm looking for. I need the ability to customize the entry for commands, addresses, and data. It would be great if I could use a scripting language as well. I contacted VNR's technical support, but they haven't provided any response, and it seems like they are intentionally ignoring this issue

_________________
Auxiliary Tool Used For MonoLith Data Recovery, featuring the industry's most extensive Monolith pinouts
http://flash-matrix.com/


Top
 Profile  
 
 Post subject: Re: New NAND ID " 983E980376E4081E " With PS2251-19-26 CTRL
PostPosted: August 2nd, 2023, 8:05 
Offline
User avatar

Joined: July 8th, 2019, 12:27
Posts: 147
Location: 中国大陆浙江省湖州市
sin wrote:
Very good input. Its surely a very basic idea. However please correct me. Isn't VCCQ a constant DC signal. Why would you consider impedances in that case?
Putting LDO surely does not seems considerate towards impedance either.


--

When you integrate such a voltage divider system into the circuit, the internal resistance of the I/O pins and the pull-down resistor of the voltage divider are in series when the output is high. Therefore, when calculating the voltage at the midpoint, you also need to take the internal resistance of the pins into account. I believe this voltage divider system is not suitable for such an environment. A better approach would be to modify the gate threshold voltage of the internal N-MOSFETs in the I/O pins and provide the correct VCCQ bus voltage. This is the implementation principle of the Flash Extractor Reader Low Voltage Modification Patch that I have already completed. I apologize for any potential misunderstandings caused by my limited English proficiency while explaining this issue

_________________
Auxiliary Tool Used For MonoLith Data Recovery, featuring the industry's most extensive Monolith pinouts
http://flash-matrix.com/


Top
 Profile  
 
 Post subject: Re: New NAND ID " 983E980376E4081E " With PS2251-19-26 CTRL
PostPosted: August 3rd, 2023, 14:17 
Offline
User avatar

Joined: August 15th, 2006, 3:01
Posts: 3464
Location: CDRLabs @ Chandigarh [ India ]
Friends ,
I returned back this case and god is very mercyfull ,He gave me a HP 128GB with same controller + 2 NANDS instead of 1 :mrgreen: ,Same Issue in Reading

_________________
Regards
Amarbir S Dhillon , Chandigarh Data Recovery Labs [India]
Logical,Semi Physical And Physical Data Recovery
Website-> http://www.chandigarhdatarecovery.com


Top
 Profile  
 
 Post subject: Re: New NAND ID " 983E980376E4081E " With PS2251-19-26 CTRL
PostPosted: August 3rd, 2023, 14:51 
Offline

Joined: September 17th, 2016, 16:06
Posts: 430
Location: India
csava wrote:
sin wrote:
Very good input. Its surely a very basic idea. However please correct me. Isn't VCCQ a constant DC signal. Why would you consider impedances in that case?
Putting LDO surely does not seems considerate towards impedance either.


--

When you integrate such a voltage divider system into the circuit, the internal resistance of the I/O pins and the pull-down resistor of the voltage divider are in series when the output is high. Therefore, when calculating the voltage at the midpoint, you also need to take the internal resistance of the pins into account. I believe this voltage divider system is not suitable for such an environment. A better approach would be to modify the gate threshold voltage of the internal N-MOSFETs in the I/O pins and provide the correct VCCQ bus voltage. This is the implementation principle of the Flash Extractor Reader Low Voltage Modification Patch that I have already completed. I apologize for any potential misunderstandings caused by my limited English proficiency while explaining this issue


Sounds cool to me. What you are referring to is internal resistances. :)


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 40 posts ]  Go to page 1, 2  Next

All times are UTC - 5 hours [ DST ]


Who is online

Users browsing this forum: No registered users and 9 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group