All times are UTC - 5 hours [ DST ]




Post new topic Reply to topic  [ 14 posts ] 
Author Message
 Post subject: Need assist with monolith SD pinout soldering.
PostPosted: November 28th, 2016, 6:06 
Offline
User avatar

Joined: January 9th, 2013, 4:19
Posts: 50
Location: Israel
Hello guys,

I have some trouble with monolith SD card, we pinout the card using the 16 bit schema on VNR, but cannot get right ID's.

Here are the pinout we did: http://imgur.com/a/02xvl
ALL wire are isolated.

Here are the schema on VNR software: http://imgur.com/a/zovnQ

So we did it by this schema, but no right Id's. only some 74747474 and FEFEFEFE...and as long as i changed the configuration i get different Id's but no legit one's
I think the SD is fine and the soldering is fine too, and i need to say that the VNR is fully up to date.

Assuming the SD card is fine, Can anyone have any idea what i can do from here?


Top
 Profile  
 
 Post subject: Re: Need assist with monolith SD pinout soldering.
PostPosted: November 28th, 2016, 12:33 
Offline

Joined: October 24th, 2009, 15:22
Posts: 521
Location: Poland
Check VCC and GND - shorted?

_________________
Odzyskiwanie danych


Top
 Profile  
 
 Post subject: Re: Need assist with monolith SD pinout soldering.
PostPosted: November 29th, 2016, 5:16 
Offline
User avatar

Joined: January 9th, 2013, 4:19
Posts: 50
Location: Israel
Hi Arvika! Thanks for the reply,

No, there is no short between VCC and GND.


Top
 Profile  
 
 Post subject: Re: Need assist with monolith SD pinout soldering.
PostPosted: November 29th, 2016, 5:29 
Offline

Joined: October 24th, 2009, 15:22
Posts: 521
Location: Poland
Are you sure that this card has 16-bit nand flash? It is not common.

_________________
Odzyskiwanie danych


Top
 Profile  
 
 Post subject: Re: Need assist with monolith SD pinout soldering.
PostPosted: November 29th, 2016, 5:46 
Offline
User avatar

Joined: January 9th, 2013, 4:19
Posts: 50
Location: Israel
I think this is 8 bit SD, but if we solder 16 bit "just in case" that could make a problem?


Top
 Profile  
 
 Post subject: Re: Need assist with monolith SD pinout soldering.
PostPosted: November 29th, 2016, 8:48 
Offline

Joined: October 24th, 2009, 15:22
Posts: 521
Location: Poland
You made a lot of mistakes with connections. If I good see on picture you invert RB<->RE, WE is wrong connected etc. First check all signals. It is reason why it not work.

_________________
Odzyskiwanie danych


Top
 Profile  
 
 Post subject: Re: Need assist with monolith SD pinout soldering.
PostPosted: November 29th, 2016, 9:57 
Offline
User avatar

Joined: January 9th, 2013, 4:19
Posts: 50
Location: Israel
I'm sorry, i doable check it and all pinout's are soldered as the instruction on the schema above.
maybe the schema is wrong?


Top
 Profile  
 
 Post subject: Re: Need assist with monolith SD pinout soldering.
PostPosted: November 29th, 2016, 10:19 
Offline

Joined: October 24th, 2009, 15:22
Posts: 521
Location: Poland
Schema is ok, did you check wires? I'm almost sure that you wire it wrong. Use multimeter to check.

_________________
Odzyskiwanie danych


Top
 Profile  
 
 Post subject: Re: Need assist with monolith SD pinout soldering.
PostPosted: November 29th, 2016, 11:13 
Offline
User avatar

Joined: January 9th, 2013, 4:19
Posts: 50
Location: Israel
Yes, i check them using multimeter, no shorting - and all wires are isolated.
Thanks for trying to assist, i'm fighting on this case cuz i don't think the SD or the pinouts are bad.

Do you have any tips what can i do more? maybe changing settings on VNR?


Top
 Profile  
 
 Post subject: Re: Need assist with monolith SD pinout soldering.
PostPosted: November 29th, 2016, 12:29 
Offline

Joined: October 24th, 2009, 15:22
Posts: 521
Location: Poland
Did you check if you connect RB signal on card to RB signal on adapter?

_________________
Odzyskiwanie danych


Top
 Profile  
 
 Post subject: Re: Need assist with monolith SD pinout soldering.
PostPosted: November 30th, 2016, 5:24 
Offline
User avatar

Joined: January 9th, 2013, 4:19
Posts: 50
Location: Israel
Yes, of course.
I'm sorry the photo is not clear but all connection are like the schema.


Top
 Profile  
 
 Post subject: Re: Need assist with monolith SD pinout soldering.
PostPosted: November 30th, 2016, 5:41 
Offline

Joined: October 24th, 2009, 15:22
Posts: 521
Location: Poland
Please add new photo that we can see all wires and adapter pads.

_________________
Odzyskiwanie danych


Top
 Profile  
 
 Post subject: Re: Need assist with monolith SD pinout soldering.
PostPosted: November 30th, 2016, 6:39 
Offline
User avatar

Joined: January 9th, 2013, 4:19
Posts: 50
Location: Israel
Here: http://imgur.com/a/YlXvS

Thanks!


Top
 Profile  
 
 Post subject: Re: Need assist with monolith SD pinout soldering.
PostPosted: November 30th, 2016, 7:00 
Offline

Joined: October 24th, 2009, 15:22
Posts: 521
Location: Poland
Come on... you not change anything on pinout. I told you what is wrong, you not even check it. You make mistake with some signals. RE is still connected to RB, RB is connected to RE. And other problem. It is the reason why it not work.

_________________
Odzyskiwanie danych


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 14 posts ] 

All times are UTC - 5 hours [ DST ]


Who is online

Users browsing this forum: No registered users and 1 guest


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group