All times are UTC - 5 hours [ DST ]




Post new topic Reply to topic  [ 35 posts ]  Go to page 1, 2  Next
Author Message
 Post subject: The death of WD ROM recovery tool: U instruction
PostPosted: December 6th, 2012, 3:49 
Offline

Joined: June 28th, 2012, 14:29
Posts: 11
Location: www.drthdd.com
Function: through instruction restores normal brush to write ROM program; the scope of application: ROM program embedded in the main control chip MCU series of hard disk ( eight feet ROM chip drive circuit board ); principle: short circuit drive circuit board CPU specific foot position, Using special software, via the serial port, reflash the internal or external ROM( not data line hard circuit board ) to the CPU sends an activation command and ROM data, enable the CPU ROM program resumed control of hard work.


Method of use: to install: NET4.0,13XX series circuit board in circuit board E112 plus 3.3V voltage, connected with the serial port communication line, then drive power supply ( not connected with the data line ): run U commands, COM export, call, the following SSS is connected, the selected file, writing brush, so simple.


Attachments:
UCommand.rar [116.29 KiB]
Downloaded 2529 times
Top
 Profile  
 
 Post subject: Re: The death of WD ROM recovery tool: U instruction
PostPosted: December 16th, 2012, 14:44 
Offline

Joined: December 16th, 2012, 14:23
Posts: 3
Location: france
thanks alot
but i want explaining about how to connect pcb with serial port ?


Top
 Profile  
 
 Post subject: Re: The death of WD ROM recovery tool: U instruction
PostPosted: December 17th, 2012, 1:17 
Offline

Joined: June 28th, 2012, 14:29
Posts: 11
Location: www.drthdd.com
justin_123 wrote:
thanks alot
but i want explaining about how to connect pcb with serial port ?

QQ370909447


Attachments:
u.jpg
u.jpg [ 14.02 KiB | Viewed 20763 times ]
Top
 Profile  
 
 Post subject: Re: The death of WD ROM recovery tool: U instruction
PostPosted: December 21st, 2012, 10:37 
Offline

Banned User

Joined: December 6th, 2012, 14:49
Posts: 70
Location: Svenska
I don't understand what does this tool?
:shock:

Western digital can be hooked to a serial port as Seagate hdd?


Top
 Profile  
 
 Post subject: Re: The death of WD ROM recovery tool: U instruction
PostPosted: December 21st, 2012, 11:34 
Offline
User avatar

Joined: September 29th, 2005, 12:02
Posts: 3181
Location: Chicago
Here is what he's saying
1. Take WD PCB(ARM based) that has erased or incompatible ROM image (bricked PCB)
2. Connect serial port as shown
3. Short some magic pins to start X-Modem sequence in MCU boot code(E112 and 3.3V for PCB 13xx, 1335 for example). The number is etched on PCB as 2060-701335-xxx
4. Select correct ROM image file and flash it to the drive with the program. Program will use special loaders (called EraseL.dll, SystemL.dll) to do so
5. Per my understanding, provided utility supports only 128KB flash files (external flash chips). For 192KB flash the program will look for Erase.dll and System.dll files that are not provided, thus will not work with those.

_________________
https://www.linkedin.com/in/artemrubtsov/


Top
 Profile  
 
 Post subject: Re: The death of WD ROM recovery tool: U instruction
PostPosted: December 21st, 2012, 12:41 
Offline

Banned User

Joined: December 6th, 2012, 14:49
Posts: 70
Location: Svenska
Can this work also with pcb 2060-701477-002 ?
Also, in point 4 you say "Select correct ROM image file and flash it to the drive with the program". Where do i get the correct ROM file if my is erased?


Top
 Profile  
 
 Post subject: Re: The death of WD ROM recovery tool: U instruction
PostPosted: December 21st, 2012, 13:27 
Offline
User avatar

Joined: May 13th, 2010, 11:17
Posts: 2296
Location: Kuwait
Doomer wrote:
Here is what he's saying
1. Take WD PCB(ARM based) that has erased or incompatible ROM image (bricked PCB)
2. Connect serial port as shown
3. Short some magic pins to start X-Modem sequence in MCU boot code(E112 and 3.3V for PCB 13xx, 1335 for example). The number is etched on PCB as 2060-701335-xxx
4. Select correct ROM image file and flash it to the drive with the program. Program will use special loaders (called EraseL.dll, SystemL.dll) to do so
5. Per my understanding, provided utility supports only 128KB flash files (external flash chips). For 192KB flash the program will look for Erase.dll and System.dll files that are not provided, thus will not work with those.


Agree with you here
and wanted to add: There are many ROUTES to the SAME destination

and 4 sure, this is one of them.

but @ the end of this, something good came up here

:wink:

_________________
Kuwait Data Recovery - UNIX GTC
The only reason for time is so that everything doesn't happen at once. By: Albert Einstein


Top
 Profile  
 
 Post subject: Re: The death of WD ROM recovery tool: U instruction
PostPosted: December 22nd, 2012, 11:07 
Offline

Joined: June 28th, 2012, 14:29
Posts: 11
Location: www.drthdd.com
einstein9 wrote:
Doomer wrote:
Here is what he's saying
1. Take WD PCB(ARM based) that has erased or incompatible ROM image (bricked PCB)
2. Connect serial port as shown
3. Short some magic pins to start X-Modem sequence in MCU boot code(E112 and 3.3V for PCB 13xx, 1335 for example). The number is etched on PCB as 2060-701335-xxx
4. Select correct ROM image file and flash it to the drive with the program. Program will use special loaders (called EraseL.dll, SystemL.dll) to do so
5. Per my understanding, provided utility supports only 128KB flash files (external flash chips). For 192KB flash the program will look for Erase.dll and System.dll files that are not provided, thus will not work with those.


Agree with you here
and wanted to add: There are many ROUTES to the SAME destination

and 4 sure, this is one of them.

but @ the end of this, something good came up here

:wink:


Attachments:
写ROM过程.jpg
写ROM过程.jpg [ 33.07 KiB | Viewed 20596 times ]
Top
 Profile  
 
 Post subject: Re: The death of WD ROM recovery tool: U instruction
PostPosted: December 22nd, 2012, 11:10 
Offline

Joined: June 28th, 2012, 14:29
Posts: 11
Location: www.drthdd.com
Doomer wrote:
Here is what he's saying
1. Take WD PCB(ARM based) that has erased or incompatible ROM image (bricked PCB)
2. Connect serial port as shown
3. Short some magic pins to start X-Modem sequence in MCU boot code(E112 and 3.3V for PCB 13xx, 1335 for example). The number is etched on PCB as 2060-701335-xxx
4. Select correct ROM image file and flash it to the drive with the program. Program will use special loaders (called EraseL.dll, SystemL.dll) to do so
5. Per my understanding, provided utility supports only 128KB flash files (external flash chips). For 192KB flash the program will look for Erase.dll and System.dll files that are not provided, thus will not work with those.


Attachments:
写ROM过程1.jpg
写ROM过程1.jpg [ 36.38 KiB | Viewed 20594 times ]
Top
 Profile  
 
 Post subject: Re: The death of WD ROM recovery tool: U instruction
PostPosted: December 22nd, 2012, 22:01 
Offline
User avatar

Joined: August 19th, 2007, 17:30
Posts: 1899
Location: In your hard drive.
I tried it on a ATLANTIS PATA with erased ROM (thanks to SD tools) and it didnt work.

_________________
Buy your friends Toshiba\Hitachi and your enemies Seagate.


Top
 Profile  
 
 Post subject: Re: The death of WD ROM recovery tool: U instruction
PostPosted: December 23rd, 2012, 2:55 
Offline

Joined: June 28th, 2012, 14:29
Posts: 11
Location: www.drthdd.com
thatdellguy wrote:
I tried it on a ATLANTIS PATA with erased ROM (thanks to SD tools) and it didnt work.

The trial version only hosted 13XX series motherboards, the registered version supports 13XX, 14XX, 15XX series motherboards. More please contact QQ370909447 technical Street


Top
 Profile  
 
 Post subject: Re: The death of WD ROM recovery tool: U instruction
PostPosted: December 23rd, 2012, 20:43 
Offline

Joined: March 10th, 2006, 1:08
Posts: 35
Actually do I need to
Quote:
Short some magic pins to start X-Modem

for your utility ?


Top
 Profile  
 
 Post subject: Re: The death of WD ROM recovery tool: U instruction
PostPosted: December 23rd, 2012, 22:57 
Offline
User avatar

Joined: August 19th, 2007, 17:30
Posts: 1899
Location: In your hard drive.
What is "QQ370909447 technical Street"?

_________________
Buy your friends Toshiba\Hitachi and your enemies Seagate.


Top
 Profile  
 
 Post subject: Re: The death of WD ROM recovery tool: U instruction
PostPosted: December 24th, 2012, 4:01 
Offline
User avatar

Joined: January 28th, 2009, 10:54
Posts: 2720
Location: Greece
QQ is equivalent to MSN for China, very popular.

_________________
Northwind Data Recovery - Greece
WD Trusted Partners
http://www.northwind.gr
SandForce SSD Recovery


Top
 Profile  
 
 Post subject: Re: The death of WD ROM recovery tool: U instruction
PostPosted: December 24th, 2012, 4:39 
Offline
User avatar

Joined: August 19th, 2007, 17:30
Posts: 1899
Location: In your hard drive.
Never heard of it but figured it sounded like some ICQ messenger spin off.

_________________
Buy your friends Toshiba\Hitachi and your enemies Seagate.


Top
 Profile  
 
 Post subject: Re: The death of WD ROM recovery tool: U instruction
PostPosted: December 28th, 2012, 15:33 
Offline

Joined: January 22nd, 2012, 18:21
Posts: 30
Location: Украина.Феншуй
Jtag -taxis!

_________________
WDmarvel


Top
 Profile  
 
 Post subject: Re: The death of WD ROM recovery tool: U instruction
PostPosted: January 18th, 2013, 10:38 
Offline

Joined: January 18th, 2013, 9:46
Posts: 1
Location: egypt
we need aphoto to com plese


Top
 Profile  
 
 Post subject: Re: The death of WD ROM recovery tool: U instruction
PostPosted: January 19th, 2013, 1:45 
Offline

Joined: June 28th, 2012, 14:29
Posts: 11
Location: www.drthdd.com
ahmedshref wrote:
we need aphoto to com plese


Attachments:
COM.png
COM.png [ 140.99 KiB | Viewed 19771 times ]
Top
 Profile  
 
 Post subject: Re: The death of WD ROM recovery tool: U instruction
PostPosted: January 19th, 2013, 1:46 
Offline

Joined: June 28th, 2012, 14:29
Posts: 11
Location: www.drthdd.com
ahmedshref wrote:
we need aphoto to com plese


Attachments:
COM11.png
COM11.png [ 11.44 KiB | Viewed 19770 times ]
Top
 Profile  
 
 Post subject: Re: The death of WD ROM recovery tool: U instruction
PostPosted: January 19th, 2013, 2:13 
Offline

Joined: June 28th, 2012, 14:29
Posts: 11
Location: www.drthdd.com
ahmedshref wrote:
we need aphoto to com plese

http://www.drthdd.com/drte/index.htm


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 35 posts ]  Go to page 1, 2  Next

All times are UTC - 5 hours [ DST ]


Who is online

Users browsing this forum: Majestic-12 [Bot] and 5 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group