All times are UTC - 5 hours [ DST ]




Post new topic Reply to topic  [ 8 posts ] 
Author Message
 Post subject: LED:000000CE
PostPosted: November 9th, 2011, 13:41 
Offline

Joined: May 16th, 2009, 9:32
Posts: 329
Location: UNited Kingdom
Yes this old chestnut again
(please go easy on me)

Recent-ish Maxtor DiamondMax 22 / Seagate 7200.11
STM31000340AS
firmware MX15
date code 08384

power on hd with pcb connected to motor
get
LED:000000CC busy error
doesnt respond to ctrl z

power on hd with pcb isolated from motor
accepts ctrl z
get F3 T> prompt
enter 2 (CR)
but just get
LED:000000CE
and dont get to F3 2>


I did once get to
F3 2>
but didnt respond to Z

Please give me a hint

I have tried 'waiting longer'

Not sure about the 'shorting read channel'

Thanks


Top
 Profile  
 
 Post subject: Re: LED:000000CE
PostPosted: November 9th, 2011, 13:49 
Offline

Joined: May 16th, 2009, 9:32
Posts: 329
Location: UNited Kingdom
At F3 T>
wait 1 minute (no LED messages)
2
get LED:000000CC ie back to CC and unresponsive


Top
 Profile  
 
 Post subject: Re: LED:000000CE
PostPosted: November 9th, 2011, 18:52 
Offline

Joined: February 17th, 2009, 13:01
Posts: 111
Location: Bogotá, D.C.
HDD is locked? or bad heads.


Top
 Profile  
 
 Post subject: Re: LED:000000CE
PostPosted: November 10th, 2011, 4:27 
Offline
User avatar

Joined: January 28th, 2009, 10:54
Posts: 2889
Location: Greece
You must wait longer BEFORE you CTRL+Z.

_________________
WD Trusted Partners
http://www.northwind.gr
SandForce SSD Recovery
Ransomware Reverse Engineering - NoMoreRansom! partners


Top
 Profile  
 
 Post subject: Re: LED:000000CE
PostPosted: November 10th, 2011, 7:46 
Offline

Joined: May 16th, 2009, 9:32
Posts: 329
Location: UNited Kingdom
Thanks

I've been trying various delays before the first ^Z and then before doing 2

IF do it too soon get 000000CE
if do it too late get 000000CC

I'm trying some other commands after the initial ^Z
(if do frequent ^Z's and it continues to respond)

? gives the following output

Blks 000E24-000E24 (000001), BufAddr 001C4800-001C49FF, DBA 061C4800, BytesPerBlk 200 Online Cmd SDBP DFB
Blks 000E25-000E25 (000001), BufAddr 001C4A00-001C4BFF, DBA 061C4A00, BytesPerBlk 200 Cmd Input Buf
Blks 000E26-000E26 (000001), BufAddr 001C4C00-001C4DFF, DBA 061C4C00, BytesPerBlk 200 Diag Batch File
Blks 000E27-000E27 (000001), BufAddr 001C4E00-001C4FFF, DBA 061C4E00, BytesPerBlk 200
Blks 000E28-000E28 (000001), BufAddr 001C5000-001C51FF, DBA 061C5000, BytesPerBlk 200
Blks 000E29-000E29 (000001), BufAddr 001C5200-001C53FF, DBA 061C5200, BytesPerBlk 200
Blks 000E2A-000E2A (000001), BufAddr 001C5400-001C55FF, DBA 061C5400, BytesPerBlk 200
Blks 000E2B-000E2B (000001), BufAddr 001C5600-001C57FF, DBA 061C5600, BytesPerBlk 200
Blks 000E2C-000E2F (000004), BufAddr 001C5800-001C5FFF, DBA 061C5800, BytesPerBlk 200
Blks 000E30-000E33 (000004), BufAddr 001C6000-001C67FF, DBA 061C6000, BytesPerBlk 200
Blks 000E34-000E37 (000004), BufAddr 001C6800-001C6FFF, DBA 061C6800, BytesPerBlk 200
Blks 000E38-000E3B (000004), BufAddr 001C7000-001C77FF, DBA 061C7000, BytesPerBlk 200
Blks 000E3C-000E5B (000020), BufAddr 001C7800-001CB7FF, DBA 061C7800, BytesPerBlk 200 Diag Mode Cmd SDBP DFB
Blks 000E5C-000E7B (000020), BufAddr 001CB800-001CF7FF, DBA 061CB800, BytesPerBlk 200 Ext Test Service SDBP DSB
Blks 000E7C-000E9B (000020), BufAddr 001CF800-001D37FF, DBA 061CF800, BytesPerBlk 200
Blks 000E9C-000EBB (000020), BufAddr 001D3800-001D77FF, DBA 061D3800, BytesPerBlk 200
Blks 000EBC-000F15 (00005A), BufAddr 001D7800-001E2BFF, DBA 061D7800, BytesPerBlk 200
Blks 000F16-000F6F (00005A), BufAddr 001E2C00-001EDFFF, DBA 061E2C00, BytesPerBlk 200

and keeps responding to further ?'s forever (ie still responsive)

but if do 2 (or 1)
it blocks with 000000CC
again

I'll see if any other T level commands are working


Top
 Profile  
 
 Post subject: Re: LED:000000CE
PostPosted: November 10th, 2011, 8:11 
Offline

Joined: May 16th, 2009, 9:32
Posts: 329
Location: UNited Kingdom
Results of other level T commands

^A shows firmware info

. shows
Current R/W User LBA 00000000 LLL CHS 000000.0.0000 PLP CHS 000000.0.0000
R/W Status 1 R/W Error 00000080 Not Ready

^C (firmware reset gives)
Spinning Down

Spin Down Complete (nb motor not connected)
Elapsed Time 0.149 msecs
Delaying 5000 msec

Jumping to Power On Reset
Bogus ISR

(stuck/no response to ^Z)

power cycle, ^Z, back to level T


Top
 Profile  
 
 Post subject: Re: LED:000000CE
PostPosted: November 10th, 2011, 8:29 
Offline

Joined: May 16th, 2009, 9:32
Posts: 329
Location: UNited Kingdom
At level T
if reconnect motor and do ?
get extra two lines at end
Blks 001769-001AFA (000392), BufAddr 002ED200-0036128F, DBA 062ED200, BytesPerBlk 208 Default Diag Rd Buf
Blks 001B0C-001E9D (000392), BufAddr 00361800-003D588F, DBA 06361800, BytesPerBlk 208 Default Diag Wrt Buf


Top
 Profile  
 
 Post subject: Re: LED:000000CE
PostPosted: November 10th, 2011, 15:49 
Offline

Joined: May 16th, 2009, 9:32
Posts: 329
Location: UNited Kingdom
^Z with motor disconnected
Have to wait a bit before doing ^A
if too soon -- Error 100A DETSEC 00007001
after 20 seconds or so -- firmware info

ie seems to need the 20 seconds to stabilize
just keep running ^A till it shows as stable

can then /2
Z worked, and rest of procedure worked

Disk recovered ! :D


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 8 posts ] 

All times are UTC - 5 hours [ DST ]


Who is online

Users browsing this forum: MSN [Bot] and 23 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group