All times are UTC - 5 hours [ DST ]




Post new topic Reply to topic  [ 9 posts ] 
Author Message
 Post subject: Kingston Hyperx fury SSD 120G SHFS37A -
PostPosted: January 18th, 2018, 4:53 
Offline

Joined: March 28th, 2011, 17:45
Posts: 441
Location: italy
The SSd does not show any signals (BSY DRD etc) - even not blinking for a while - nothing of nothing.

on coil 2R2 i misured 2,8 volt
on coil 1R2 0,0 volt

i suspect a spike killed the fuse diode but i am not sure which is fuse diode here..


Attachments:
20180118_094329.jpg
20180118_094329.jpg [ 675.25 KiB | Viewed 9225 times ]
20180118_094349.jpg
20180118_094349.jpg [ 672.32 KiB | Viewed 9225 times ]
Top
 Profile  
 
 Post subject: Re: Kingston Hyperx fury SSD 120G SHFS37A -
PostPosted: January 18th, 2018, 5:32 
Offline
User avatar

Joined: September 8th, 2009, 18:21
Posts: 15461
Location: Australia
viewtopic.php?f=10&t=35783
viewtopic.php?f=10&p=241918

_________________
A backup a day keeps DR away.


Top
 Profile  
 
 Post subject: Re: Kingston Hyperx fury SSD 120G SHFS37A -
PostPosted: January 18th, 2018, 15:23 
Offline
User avatar

Joined: September 8th, 2009, 18:21
Posts: 15461
Location: Australia
If you are measuring +2.8V at one of the supplies, then the "fuse diode" (sic) must be OK.

If any regulator has a 0V output, then ...

1/ The regulator may be faulty.

2/ The regulator may not be turned on. Measure the voltage at its Enable pin.

3/ The regulator's output may be shorted to ground. Measure the resistance between the coil (or capacitors) and ground.

_________________
A backup a day keeps DR away.


Top
 Profile  
 
 Post subject: Re: Kingston Hyperx fury SSD 120G SHFS37A -
PostPosted: January 30th, 2018, 13:21 
Offline

Joined: March 28th, 2011, 17:45
Posts: 441
Location: italy
i have made some more misurement,
in red.


Attachments:
diagnostic.jpg
diagnostic.jpg [ 336.82 KiB | Viewed 8984 times ]
Top
 Profile  
 
 Post subject: Re: Kingston Hyperx fury SSD 120G SHFS37A -
PostPosted: January 30th, 2018, 18:11 
Offline
User avatar

Joined: September 8th, 2009, 18:21
Posts: 15461
Location: Australia
Measure the voltages at coils A and B.

Measure the resistance between ground and the 1R0 coil (in the absence of power).


Attachments:
coils.jpg
coils.jpg [ 167.2 KiB | Viewed 8954 times ]

_________________
A backup a day keeps DR away.
Top
 Profile  
 
 Post subject: Re: Kingston Hyperx fury SSD 120G SHFS37A -
PostPosted: January 30th, 2018, 19:11 
Offline

Joined: March 28th, 2011, 17:45
Posts: 441
Location: italy
in black text:

coil 1R0 to ground= 34 ohm
coil A to ground = + 1 volt
coil B to ground = + 2.8 volt


Attachments:
coils.jpg
coils.jpg [ 106.5 KiB | Viewed 8949 times ]
Top
 Profile  
 
 Post subject: Re: Kingston Hyperx fury SSD 120G SHFS37A -
PostPosted: January 30th, 2018, 20:48 
Offline
User avatar

Joined: September 8th, 2009, 18:21
Posts: 15461
Location: Australia
I don't understand why there are two 2.8V supplies, especially since there are no NANDs on the controller side of the PCB. Perhaps one is the controller's Vio supply?

Coil A (1V) would be the Vcore supply for the controller.

The load resistance of the 1R0 coil seems very low. Does the "13 1F" chip get hot?

Is there a direct connection between the 1R0 coil and any of the UART pins? I suspect that one of these pins would be a +3.3V supply (or maybe 2.8V ?). Can you tell us the voltages on the UART pins?


Attachments:
UART.jpg
UART.jpg [ 73.24 KiB | Viewed 8932 times ]

_________________
A backup a day keeps DR away.
Top
 Profile  
 
 Post subject: Re: Kingston Hyperx fury SSD 120G SHFS37A -
PostPosted: January 31st, 2018, 9:16 
Offline

Joined: March 28th, 2011, 17:45
Posts: 441
Location: italy
UART pins misures to ground to them one by one = 0,0 volts.
the 13 1F stay not hot.
the controller stay a bit hot.


Top
 Profile  
 
 Post subject: Re: Kingston Hyperx fury SSD 120G SHFS37A -
PostPosted: January 31st, 2018, 14:19 
Offline
User avatar

Joined: September 8th, 2009, 18:21
Posts: 15461
Location: Australia
What is the voltage on the Enable pin (EN)?

(Other photos of a similar PCB suggest that the "13 1F" part is equivalent to an APW8804.)


Attachments:
APW8804_app_cct.gif
APW8804_app_cct.gif [ 11.79 KiB | Viewed 8871 times ]
APW8804_pinout.jpg
APW8804_pinout.jpg [ 175.25 KiB | Viewed 8871 times ]

_________________
A backup a day keeps DR away.
Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 9 posts ] 

All times are UTC - 5 hours [ DST ]


Who is online

Users browsing this forum: No registered users and 28 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group