All times are UTC - 5 hours [ DST ]




Post new topic Reply to topic  [ 10 posts ] 
Author Message
 Post subject: 7200.11 shows 0mb
PostPosted: September 3rd, 2009, 5:19 
Offline

Joined: November 9th, 2006, 22:36
Posts: 343
hi all
i have the seagate drive witht eh error of 0mb, i have done several of these with no issues but this one will not work.

drive spins up, shows, model , serial and firmware sd15, it then shows translation error,
i run the solution and it fails, i try and run it manually and i get the below results

F3 T>/1

F3 1>N1

F3 1>
F3 T>i4,1,22

F3 T>m0,6,2,,,,,22
Max Wr Retries = 00, Max Rd Retries = 00, Max ECC T-Level = 14, Max Certify Rewrite Retries = 00C8

Error 1008 DETSEC 0000500D
User Partition Format Failed - Elapsed Time 0 mins 00 secs
R/W Sense 00000002, R/W Error 00000084, File Error 00001002
Blk Addr 01080001, Blk Addr Type D0, Cyl 00000000, Hd 00

F3 T>


have i missed something here.

Thank you


Top
 Profile  
 
 Post subject: Re: 7200.11 shows 0mb
PostPosted: September 3rd, 2009, 6:08 
Offline

Joined: October 13th, 2008, 7:29
Posts: 1483
BADS in SA?

up the read/write retries when you regen translator.


Top
 Profile  
 
 Post subject: Re: 7200.11 shows 0mb
PostPosted: September 3rd, 2009, 6:13 
Offline

Joined: November 9th, 2006, 22:36
Posts: 343
hi,
thank you for the reply
do you mean N? up to a larger nuymber such as 10 or more

thank you


Top
 Profile  
 
 Post subject: Re: 7200.11 shows 0mb
PostPosted: September 3rd, 2009, 9:43 
Offline

Joined: September 2nd, 2009, 3:37
Posts: 5
Location: India
Hi ,

Increasing retries refers to :

m0,6,2,2,2,0,0,22 , but confirm from a recovery pro here before use , using the option 2 for read and write retries .

and do not use the command m0,1,1,0,0,0,0,22 it is mentioned in some other forums as a remedy to translator command failure .


Cheers,
Nitin


Top
 Profile  
 
 Post subject: Re: 7200.11 shows 0mb
PostPosted: September 3rd, 2009, 19:10 
Offline

Joined: November 9th, 2006, 22:36
Posts: 343
hi guys

went through several more atemps and it is showing that it is most lieky an isse with bad sectors in SA as pointed out by HZZ SPAZ.

as the drive was dropped i am wondering if it is a scratch on the platters or possibly a fault with heads,
have you come accross this before, if it is bad blocks in SA can anything be done to work around issue ?

thx for all replies


Top
 Profile  
 
 Post subject: Re: 7200.11 shows 0mb
PostPosted: September 4th, 2009, 4:24 
Offline

Joined: October 13th, 2008, 7:29
Posts: 1483
after you perform the procedure to regen translator does the hard drive LBA appear correctly before powering down?

See if you can access data without powering the disk down after you run the commands.


Top
 Profile  
 
 Post subject: Re: 7200.11 shows 0mb
PostPosted: September 6th, 2009, 4:50 
Offline

Joined: November 9th, 2006, 22:36
Posts: 343
Hi
lba does not appear. Tried new heads same thing exactly happens


Top
 Profile  
 
 Post subject: Re: 7200.11 shows 0mb
PostPosted: September 6th, 2009, 6:51 
Offline

Joined: July 28th, 2009, 16:03
Posts: 60
Location: washington D.C
@Crecomp,

see if u can find something here
http://www.msfn.org/board/solution-seag ... ge-80.html
http://www.msfn.org/board/solution-seag ... ntry881318


Top
 Profile  
 
 Post subject: Re: 7200.11 shows 0mb
PostPosted: September 8th, 2009, 9:22 
Offline

Joined: November 9th, 2006, 15:15
Posts: 2986
I assume from the post that you have some problem with defect table. Can you view PLIST or Slip list with 'V' command?


Top
 Profile  
 
 Post subject: Re: 7200.11 shows 0mb
PostPosted: September 8th, 2009, 10:11 
Offline

Joined: November 9th, 2006, 15:15
Posts: 2986
Nitin wrote:
Hi ,



and do not use the command m0,1,1,0,0,0,0,22 it is mentioned in some other forums as a remedy to translator command failure .


Cheers,
Nitin


this will destroy user data.


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 10 posts ] 

All times are UTC - 5 hours [ DST ]


Who is online

Users browsing this forum: No registered users and 45 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group