All times are UTC - 5 hours [ DST ]




Post new topic Reply to topic  [ 7 posts ] 
Author Message
 Post subject: Samsung HN-M101MBB slider stuck on insde platter
PostPosted: July 9th, 2018, 5:04 
Offline

Joined: March 9th, 2012, 7:02
Posts: 34
Location: Dubai
I have 1TB Samsung HNM101MBB drive for data recovery. bottom 2 heads 0-1 are with out slider. After looking closely inside the platter those sliders are stuck to platters.

I tried to shake the drive to remove sliders but it could not come out. Is there any way to get those out so that I can replace the heads and read the drive.

I am planning to get below platter extractor and holder for 280$. my questions are 1. removing the platters and putting back what precaution I need to have? 2. Do I need to keep the vertical alignment accurate or little bit offset will work? 3. Are these platter holders safe for platters as these probably hold platter by magnet.

Attachment:
platterswap.jpg
platterswap.jpg [ 56.2 KiB | Viewed 738 times ]

_________________
Best Regards,
Murtaza H.
FreekinGeeks Data Recovery


Top
 Profile  
 
 Post subject: Re: Samsung HN-M101MBB slider stuck on insde platter
PostPosted: July 9th, 2018, 5:42 
Offline

Joined: September 29th, 2005, 4:10
Posts: 256
Location: Moscow
On the donor, first train.
This model does not always successfully transfer the permutation of the plates.

You can wash the adhered slider with liquid.


Top
 Profile  
 
 Post subject: Re: Samsung HN-M101MBB slider stuck on insde platter
PostPosted: July 9th, 2018, 6:20 
Offline
User avatar

Joined: December 12th, 2005, 3:32
Posts: 662
Location: Belgrade
You have to know that tool you want to buy does not have basic option what original was made for.
Idea behind tool was not to make Christmas tree out of platters.
Idea was that you are able to spin them around and have support for cleaning them with cotton.
It was never made to be platter change support but platter cleaning tool.
Guys who copied it do not work in data recovery or do not understand what are needs. Don't buy something just because you see it on picture.
Think two times. Why would you buy something for 280 USD when you can just use 4 hdd chassis .
With out a thread to grip the platter it just does not have any sense....

_________________
HddSurgery - Professional Data Recovery Tools


Top
 Profile  
 
 Post subject: Re: Samsung HN-M101MBB slider stuck on insde platter
PostPosted: July 9th, 2018, 8:38 
Offline

Joined: December 8th, 2010, 11:37
Posts: 587
Location: Ottawa, Canada
You could try fishing line to snag and remove them, like Andy Watson shows in this article.

_________________
Sabo Computer Repairs & Data Recovery


Top
 Profile  
 
 Post subject: Re: Samsung HN-M101MBB slider stuck on insde platter
PostPosted: July 9th, 2018, 12:00 
Offline
User avatar

Joined: August 15th, 2006, 3:01
Posts: 2538
Location: CDRLabs @ Chandigarh [ India ]
Murtazah wrote:
I have 1TB Samsung HNM101MBB drive for data recovery. bottom 2 heads 0-1 are with out slider. After looking closely inside the platter those sliders are stuck to platters.

I tried to shake the drive to remove sliders but it could not come out. Is there any way to get those out so that I can replace the heads and read the drive.

I am planning to get below platter extractor and holder for 280$. my questions are 1. removing the platters and putting back what precaution I need to have? 2. Do I need to keep the vertical alignment accurate or little bit offset will work? 3. Are these platter holders safe for platters as these probably hold platter by magnet.

Attachment:
platterswap.jpg



Well,
Doing This is a Piece of Cake .Tape the platters from two ends ,Take the platter assembly out and take out the sliders ,Its Not even 1 Dollar Cost if You Know How to do it ,If you are not experienced Learn it

_________________
Regards
Amarbir S Dhillon , Chandigarh Data Recovery Labs
Logical,Semi Physical And Physical Data Recovery
Website-> http://www.chandigarhdatarecovery.com


Top
 Profile  
 
 Post subject: Re: Samsung HN-M101MBB slider stuck on insde platter
PostPosted: July 9th, 2018, 13:56 
Offline

Joined: October 5th, 2015, 18:53
Posts: 433
Location: Canada
I am using plastic stick to remove sliders without platters removing.


Top
 Profile  
 
 Post subject: Re: Samsung HN-M101MBB slider stuck on insde platter
PostPosted: July 15th, 2018, 14:55 
Offline

Joined: March 9th, 2012, 7:02
Posts: 34
Location: Dubai
Thank you all for all your reply and suggestions.

Removed platters with the help of stickers, used the plastic stick to remove the slider and that's it.

Drive now imaging. :D
Attachment:
WhatsApp Image 2018-07-15 at 10.17.01 PM(2).jpeg
WhatsApp Image 2018-07-15 at 10.17.01 PM(2).jpeg [ 103.39 KiB | Viewed 490 times ]

Attachment:
WhatsApp Image 2018-07-15 at 10.17.01 PM(1).jpeg
WhatsApp Image 2018-07-15 at 10.17.01 PM(1).jpeg [ 97.59 KiB | Viewed 490 times ]

Attachment:
WhatsApp Image 2018-07-15 at 10.17.00 PM.jpeg
WhatsApp Image 2018-07-15 at 10.17.00 PM.jpeg [ 76.18 KiB | Viewed 490 times ]

Attachment:
WhatsApp Image 2018-07-15 at 10.17.01 PM.jpeg
WhatsApp Image 2018-07-15 at 10.17.01 PM.jpeg [ 441.54 KiB | Viewed 490 times ]

_________________
Best Regards,
Murtaza H.
FreekinGeeks Data Recovery


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 7 posts ] 

All times are UTC - 5 hours [ DST ]


Who is online

Users browsing this forum: Bing [Bot], Google [Bot], Google Adsense [Bot] and 33 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group