smartctl 7.5 2025-04-30 r5714 [x86_64-linux-7.2.6-201.nobara.fc44.x86_64] (local build)
Copyright (C) 2002-25, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     Western Digital Green
Device Model:     WDC WD5000AZRX-00A8LB0
Serial Number:    WD-WCC1U1920791
LU WWN Device Id: 5 0014ee 25d8552d4
Firmware Version: 01.01A01
User Capacity:    500,107,862,016 bytes [500 GB]
Sector Sizes:     512 bytes logical, 4096 bytes physical
Device is:        In smartctl database 7.5/6204
ATA Version is:   ATA8-ACS (minor revision not indicated)
SATA Version is:  SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is:    Mon Oct 12 13:03:21 2026 IST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is:   Unavailable
APM feature is:   Unavailable
Rd look-ahead is: Enabled
Write cache is:   Enabled
DSN feature is:   Unavailable
ATA Security is:  Disabled, NOT FROZEN [SEC1]

=== START OF READ SMART DATA SECTION ===
SMART Status not supported: Incomplete response, ATA output registers missing
SMART overall-health self-assessment test result: PASSED
Warning: This result is based on an Attribute check.

General SMART Values:
Offline data collection status:  (0x80)	Offline data collection activity
					was never started.
					Auto Offline Data Collection: Enabled.
Self-test execution status:      (   0)	The previous self-test routine completed
					without error or no self-test has ever 
					been run.
Total time to complete Offline 
data collection: 		( 6420) seconds.
Offline data collection
capabilities: 			 (0x7b) SMART execute Offline immediate.
					Auto Offline data collection on/off support.
					Suspend Offline collection upon new
					command.
					Offline surface scan supported.
					Self-test supported.
					Conveyance Self-test supported.
					Selective Self-test supported.
SMART capabilities:            (0x0003)	Saves SMART data before entering
					power-saving mode.
					Supports SMART auto save timer.
Error logging capability:        (0x01)	Error logging supported.
					General Purpose Logging supported.
Short self-test routine 
recommended polling time: 	 (   2) minutes.
Extended self-test routine
recommended polling time: 	 (  76) minutes.
Conveyance self-test routine
recommended polling time: 	 (   5) minutes.
SCT capabilities: 	       (0x30b5)	SCT Status supported.
					SCT Feature Control supported.
					SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAGS    VALUE WORST THRESH FAIL RAW_VALUE
  1 Raw_Read_Error_Rate     POSR-K   100   253   051    -    0
  3 Spin_Up_Time            POS--K   143   143   021    -    3841
  4 Start_Stop_Count        -O--CK   100   100   000    -    8
  5 Reallocated_Sector_Ct   PO--CK   200   200   140    -    0
  7 Seek_Error_Rate         -OSR-K   199   192   000    -    60
  9 Power_On_Hours          -O--CK   100   100   000    -    2
 10 Spin_Retry_Count        -O--CK   100   253   000    -    0
 11 Calibration_Retry_Count -O--CK   100   253   000    -    0
 12 Power_Cycle_Count       -O--CK   100   100   000    -    8
192 Power-Off_Retract_Count -O--CK   200   200   000    -    15
193 Load_Cycle_Count        -O--CK   200   200   000    -    4
194 Temperature_Celsius     -O---K   107   107   000    -    36
196 Reallocated_Event_Count -O--CK   200   200   000    -    0
197 Current_Pending_Sector  -O--CK   200   200   000    -    0
198 Offline_Uncorrectable   ----CK   100   253   000    -    0
199 UDMA_CRC_Error_Count    -O--CK   200   253   000    -    0
200 Multi_Zone_Error_Rate   ---R--   100   253   000    -    0
                            ||||||_ K auto-keep
                            |||||__ C event count
                            ||||___ R error rate
                            |||____ S speed/performance
                            ||_____ O updated online
                            |______ P prefailure warning

General Purpose Log Directory Version 1
SMART           Log Directory Version 1 [multi-sector log support]
Address    Access  R/W   Size  Description
0x00       GPL,SL  R/O      1  Log Directory
0x01           SL  R/O      1  Summary SMART error log
0x02           SL  R/O      5  Comprehensive SMART error log
0x03       GPL     R/O      6  Ext. Comprehensive SMART error log
0x06           SL  R/O      1  SMART self-test log
0x07       GPL     R/O      1  Extended self-test log
0x09           SL  R/W      1  Selective self-test log
0x10       GPL     R/O      1  NCQ Command Error log
0x11       GPL     R/O      1  SATA Phy Event Counters log
0x80-0x9f  GPL,SL  R/W     16  Host vendor specific log
0xa0-0xa7  GPL,SL  VS      16  Device vendor specific log
0xa8-0xb7  GPL,SL  VS       1  Device vendor specific log
0xbd       GPL,SL  VS       1  Device vendor specific log
0xc0       GPL,SL  VS       1  Device vendor specific log
0xc1       GPL     VS      93  Device vendor specific log
0xe0       GPL,SL  R/W      1  SCT Command/Status
0xe1       GPL,SL  R/W      1  SCT Data Transfer

SMART Extended Comprehensive Error Log Version: 1 (6 sectors)
Device Error Count: 866 (device log contains only the most recent 24 errors)
	CR     = Command Register
	FEATR  = Features Register
	COUNT  = Count (was: Sector Count) Register
	LBA_48 = Upper bytes of LBA High/Mid/Low Registers ]  ATA-8
	LH     = LBA High (was: Cylinder High) Register    ]   LBA
	LM     = LBA Mid (was: Cylinder Low) Register      ] Register
	LL     = LBA Low (was: Sector Number) Register     ]
	DV     = Device (was: Device/Head) Register
	DC     = Device Control Register
	ER     = Error register
	ST     = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 866 [1] occurred at disk power-on lifetime: 2 hours (0 days + 2 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  04 -- 51 00 08 00 00 00 00 00 00 40 00  Error: ABRT 8 sectors at LBA = 0x00000000 = 0

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 00 00 00 08 00 00 00 00 00 00 40 00     00:00:30.099  READ DMA EXT
  25 00 00 00 08 00 00 00 00 00 00 40 00     00:00:30.081  READ DMA EXT
  25 00 00 00 08 00 00 00 00 00 00 40 00     00:00:30.062  READ DMA EXT
  25 00 00 00 08 00 00 00 00 00 00 40 00     00:00:30.043  READ DMA EXT
  25 00 00 00 08 00 00 00 00 00 00 40 00     00:00:30.025  READ DMA EXT

Error 865 [0] occurred at disk power-on lifetime: 2 hours (0 days + 2 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  04 -- 51 00 08 00 00 00 00 00 00 40 00  Error: ABRT 8 sectors at LBA = 0x00000000 = 0

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 00 00 00 08 00 00 00 00 00 00 40 00     00:00:30.081  READ DMA EXT
  25 00 00 00 08 00 00 00 00 00 00 40 00     00:00:30.062  READ DMA EXT
  25 00 00 00 08 00 00 00 00 00 00 40 00     00:00:30.043  READ DMA EXT
  25 00 00 00 08 00 00 00 00 00 00 40 00     00:00:30.025  READ DMA EXT
  25 00 00 00 08 00 00 00 00 00 00 40 00     00:00:30.006  READ DMA EXT

Error 864 [23] occurred at disk power-on lifetime: 2 hours (0 days + 2 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  04 -- 51 00 08 00 00 00 00 00 00 40 00  Error: ABRT 8 sectors at LBA = 0x00000000 = 0

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 00 00 00 08 00 00 00 00 00 00 40 00     00:00:30.062  READ DMA EXT
  25 00 00 00 08 00 00 00 00 00 00 40 00     00:00:30.043  READ DMA EXT
  25 00 00 00 08 00 00 00 00 00 00 40 00     00:00:30.025  READ DMA EXT
  25 00 00 00 08 00 00 00 00 00 00 40 00     00:00:30.006  READ DMA EXT
  ec 00 00 00 01 00 00 00 00 00 00 00 00     00:00:29.993  IDENTIFY DEVICE

Error 863 [22] occurred at disk power-on lifetime: 2 hours (0 days + 2 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  04 -- 51 00 08 00 00 00 00 00 00 40 00  Error: ABRT 8 sectors at LBA = 0x00000000 = 0

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 00 00 00 08 00 00 00 00 00 00 40 00     00:00:30.043  READ DMA EXT
  25 00 00 00 08 00 00 00 00 00 00 40 00     00:00:30.025  READ DMA EXT
  25 00 00 00 08 00 00 00 00 00 00 40 00     00:00:30.006  READ DMA EXT
  ec 00 00 00 01 00 00 00 00 00 00 00 00     00:00:29.993  IDENTIFY DEVICE
  25 00 00 00 08 00 00 00 00 00 00 40 00     00:00:29.942  READ DMA EXT

Error 862 [21] occurred at disk power-on lifetime: 2 hours (0 days + 2 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  04 -- 51 00 08 00 00 00 00 00 00 40 00  Error: ABRT 8 sectors at LBA = 0x00000000 = 0

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 00 00 00 08 00 00 00 00 00 00 40 00     00:00:30.025  READ DMA EXT
  25 00 00 00 08 00 00 00 00 00 00 40 00     00:00:30.006  READ DMA EXT
  ec 00 00 00 01 00 00 00 00 00 00 00 00     00:00:29.993  IDENTIFY DEVICE
  25 00 00 00 08 00 00 00 00 00 00 40 00     00:00:29.942  READ DMA EXT
  25 00 00 00 08 00 00 00 00 00 00 40 00     00:00:29.924  READ DMA EXT

Error 861 [20] occurred at disk power-on lifetime: 2 hours (0 days + 2 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  04 -- 51 00 08 00 00 00 00 00 00 40 00  Error: ABRT 8 sectors at LBA = 0x00000000 = 0

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 00 00 00 08 00 00 00 00 00 00 40 00     00:00:30.006  READ DMA EXT
  ec 00 00 00 01 00 00 00 00 00 00 00 00     00:00:29.993  IDENTIFY DEVICE
  25 00 00 00 08 00 00 00 00 00 00 40 00     00:00:29.942  READ DMA EXT
  25 00 00 00 08 00 00 00 00 00 00 40 00     00:00:29.924  READ DMA EXT
  25 00 00 00 08 00 00 00 00 00 00 40 00     00:00:29.906  READ DMA EXT

Error 860 [19] occurred at disk power-on lifetime: 2 hours (0 days + 2 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  04 -- 51 00 08 00 00 00 00 00 00 40 00  Error: ABRT 8 sectors at LBA = 0x00000000 = 0

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 00 00 00 08 00 00 00 00 00 00 40 00     00:00:29.942  READ DMA EXT
  25 00 00 00 08 00 00 00 00 00 00 40 00     00:00:29.924  READ DMA EXT
  25 00 00 00 08 00 00 00 00 00 00 40 00     00:00:29.906  READ DMA EXT
  25 00 00 00 08 00 00 00 00 00 00 40 00     00:00:29.887  READ DMA EXT
  25 00 00 00 08 00 00 00 00 00 00 40 00     00:00:29.868  READ DMA EXT

Error 859 [18] occurred at disk power-on lifetime: 2 hours (0 days + 2 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  04 -- 51 00 08 00 00 00 00 00 00 40 00  Error: ABRT 8 sectors at LBA = 0x00000000 = 0

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 00 00 00 08 00 00 00 00 00 00 40 00     00:00:29.924  READ DMA EXT
  25 00 00 00 08 00 00 00 00 00 00 40 00     00:00:29.906  READ DMA EXT
  25 00 00 00 08 00 00 00 00 00 00 40 00     00:00:29.887  READ DMA EXT
  25 00 00 00 08 00 00 00 00 00 00 40 00     00:00:29.868  READ DMA EXT
  25 00 00 00 08 00 00 00 00 00 00 40 00     00:00:29.849  READ DMA EXT

SMART Extended Self-test Log Version: 1 (1 sectors)
No self-tests have been logged.  [To run self-tests, use: smartctl -t]

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

SCT Status Version:                  3
SCT Version (vendor specific):       258 (0x0102)
Device State:                        Active (0)
Current Temperature:                    36 Celsius
Power Cycle Min/Max Temperature:     36/36 Celsius
Lifetime    Min/Max Temperature:     28/36 Celsius
Under/Over Temperature Limit Count:   0/0
Vendor specific:
01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

SCT Temperature History Version:     2
Temperature Sampling Period:         1 minute
Temperature Logging Interval:        1 minute
Min/Max recommended Temperature:      0/60 Celsius
Min/Max Temperature Limit:           -41/85 Celsius
Temperature History Size (Index):    478 (115)

Index    Estimated Time   Temperature Celsius
 116    2026-10-12 05:06     ?  -
 ...    ..(361 skipped).    ..  -
   0    2026-10-12 11:08     ?  -
   1    2026-10-12 11:09    28  *********
   2    2026-10-12 11:10     ?  -
   3    2026-10-12 11:11    31  ************
   4    2026-10-12 11:12     ?  -
   5    2026-10-12 11:13    28  *********
   6    2026-10-12 11:14     ?  -
   7    2026-10-12 11:15    28  *********
   8    2026-10-12 11:16     ?  -
   9    2026-10-12 11:17    31  ************
  10    2026-10-12 11:18     ?  -
  11    2026-10-12 11:19    31  ************
  12    2026-10-12 11:20     ?  -
  13    2026-10-12 11:21    28  *********
  14    2026-10-12 11:22    31  ************
  15    2026-10-12 11:23    31  ************
  16    2026-10-12 11:24     ?  -
  17    2026-10-12 11:25    31  ************
  18    2026-10-12 11:26    32  *************
 ...    ..(  5 skipped).    ..  *************
  24    2026-10-12 11:32    32  *************
  25    2026-10-12 11:33     ?  -
  26    2026-10-12 11:34    31  ************
  27    2026-10-12 11:35    33  **************
 ...    ..(  7 skipped).    ..  **************
  35    2026-10-12 11:43    33  **************
  36    2026-10-12 11:44    32  *************
 ...    ..( 34 skipped).    ..  *************
  71    2026-10-12 12:19    32  *************
  72    2026-10-12 12:20     ?  -
  73    2026-10-12 12:21    31  ************
  74    2026-10-12 12:22    32  *************
  75    2026-10-12 12:23    33  **************
  76    2026-10-12 12:24     ?  -
  77    2026-10-12 12:25    34  ***************
  78    2026-10-12 12:26    35  ****************
 ...    ..(  7 skipped).    ..  ****************
  86    2026-10-12 12:34    35  ****************
  87    2026-10-12 12:35    36  *****************
  88    2026-10-12 12:36    36  *****************
  89    2026-10-12 12:37     ?  -
  90    2026-10-12 12:38    28  *********
  91    2026-10-12 12:39     ?  -
  92    2026-10-12 12:40    28  *********
  93    2026-10-12 12:41    28  *********
  94    2026-10-12 12:42    29  **********
  95    2026-10-12 12:43    29  **********
  96    2026-10-12 12:44    30  ***********
  97    2026-10-12 12:45    30  ***********
  98    2026-10-12 12:46     ?  -
  99    2026-10-12 12:47    31  ************
 100    2026-10-12 12:48     ?  -
 101    2026-10-12 12:49    32  *************
 102    2026-10-12 12:50     ?  -
 103    2026-10-12 12:51    33  **************
 104    2026-10-12 12:52    33  **************
 105    2026-10-12 12:53    34  ***************
 106    2026-10-12 12:54    34  ***************
 107    2026-10-12 12:55    34  ***************
 108    2026-10-12 12:56    35  ****************
 ...    ..(  4 skipped).    ..  ****************
 113    2026-10-12 13:01    35  ****************
 114    2026-10-12 13:02     ?  -
 115    2026-10-12 13:03    36  *****************

SCT Error Recovery Control command not supported

Device Statistics (GP/SMART Log 0x04) not supported

Pending Defects log (GP Log 0x0c) not supported

SATA Phy Event Counters (GP Log 0x11)
ID      Size     Value  Description
0x0001  2            0  Command failed due to ICRC error
0x0002  2            0  R_ERR response for data FIS
0x0003  2            0  R_ERR response for device-to-host data FIS
0x0004  2            0  R_ERR response for host-to-device data FIS
0x0005  2            0  R_ERR response for non-data FIS
0x0006  2            0  R_ERR response for device-to-host non-data FIS
0x0007  2            0  R_ERR response for host-to-device non-data FIS
0x0008  2            0  Device-to-host non-data FIS retries
0x0009  2            1  Transition from drive PhyRdy to drive PhyNRdy
0x000a  2            1  Device-to-host register FISes sent due to a COMRESET
0x000b  2            0  CRC errors within host-to-device FIS
0x000f  2            0  R_ERR response for host-to-device data FIS, CRC
0x0012  2            0  R_ERR response for host-to-device non-data FIS, CRC
0x8000  4           47  Vendor specific

