HTS541612J9SA00

[sempre]

Hi to all!

this hd when binding has rpm, but not moves heads look log!

It they problem in nvram?
on- DRD-DSC ERR-ABRT
Selected family......................... : HTS548
Model by ID............................. : <ID IS NOT READ>

NV-RAM reading........................................................ : Error
Initialization error
Error : Error switching to techno mode

UNIVERSAL UTILITY

HDD does not support set max LBA
HDD does not support S.M.A.R.T.
Write cache............................. : not supported

Soft reset ...
Ok

Determine rotational frequency
RPM..................................... : Fail to determinate

Bus test started (ports x2, x3, x4, x5)
Writing "00" to ports
Status.................................. : Ok
"Running set to one bit" test
Status.................................. : Ok
Writing "FF" to ports
Status.................................. : Ok
"Running set to zero bit" test
Status.................................. : Ok
Errors not found

Sector buffer test
Ok

Write sector buffer error (ABR) 51 / 04
Soft reset ...
Ok

IRQ Test
Ok

[Amarbir[CDR-Labs]]

Hi to all!

this hd when binding has rpm, but not moves heads look log!

It they problem in nvram?
on- DRD-DSC ERR-ABRT
Selected family......................... : HTS548
Model by ID............................. : <ID IS NOT READ>

NV-RAM reading........................................................ : Error
Initialization error
Error : Error switching to techno mode

UNIVERSAL UTILITY

HDD does not support set max LBA
HDD does not support S.M.A.R.T.
Write cache............................. : not supported

Soft reset ...
Ok

Determine rotational frequency
RPM..................................... : Fail to determinate

Bus test started (ports x2, x3, x4, x5)
Writing "00" to ports
Status.................................. : Ok
"Running set to one bit" test
Status.................................. : Ok
Writing "FF" to ports
Status.................................. : Ok
"Running set to zero bit" test
Status.................................. : Ok
Errors not found

Sector buffer test
Ok

Write sector buffer error (ABR) 51 / 04
Soft reset ...
Ok

IRQ Test
Ok

Sempre ,
That DR tools you Have I Know you Are a Old Seasoned DR Pro But then also was interested

[sempre]

Sempre ,
That DR tools you Have I Know you Are a Old Seasoned DR Pro But then also was interested[/quote]


not I understood!

[Amarbir[CDR-Labs]]

Sempre ,
That DR tools you Have I Know you Are a Old Seasoned DR Pro But then also was interested

not I understood!
[/quote]

Mate ,
I Was Asking Do You Have Salvation And Ace tools

[sempre]

Some help??

Wait....

[shahij]

no comment

[Amarbir[CDR-Labs]]

Hi ,
It Could Be the PCb Please Change And Try ,This is a Stepper Motor And even One BaD channel Will Have a Issue

[JackRipper]

Hello,

I am having issues with this same drive. Every 3-4 seconds I could hear the heads trying to read. Where do I start on how to diagnose what the issue could be?

Thanks,

-JR

[beto]

If hdd reach´s readiness u could tried to did a surface scan, and check how many and wich kind of sectors show like bad check at ATA registers , but if u heard the hdd trying to read could be too surface damaged or MHA problems,
Regards

[JackRipper]

Actually, I try to connect via USB and would not load. Cannot see in device manager or dir tree. I do a direct connection (laptop) and get BSOD device error.

[shahij]

Actually, I try to connect via USB and would not load. Cannot see in device manager or dir tree. I do a direct connection (laptop) and get BSOD device error.

connect using 2.5 to 3.5 converter, report using MHDD.

[sempre]

Actually, I try to connect via USB and would not load. Cannot see in device manager or dir tree. I do a direct connection (laptop) and get BSOD device error.

connect using 2.5 to 3.5 converter, report using MHDD.

Yes conected using 2,5 to3,5 converter,report mhdd.

Not ready => LBA 0
DRSC DRDY ABRT ERR