BGA Rework Station - For NAND Flash + HDD PCB

[Amarbir[CDR-Labs]]

Guys ,
Does anyone Of you Have a BGA Rework station To work On the following

1 : BGA Controllers On Flash Media
2 : BGA Nand Flash Memory IC
3 : BGA Chip On PCB Like MCU Etc Etc

Love To Hear From You All

[quasimodo]

Yes i would think most do

[Amarbir[CDR-Labs]]

Yes i would think most do

Well,
May i Know What all Can Work For The Stuff i Asked For I Have a Jovy That Never Worked Since Day One and i Was Lazy Enough Not To Get the Main Controller Rectified .I think for Dr work even the cheapest Chinese T-862 Should Be OK I Guess

[BlackST]

Cheap chinese stuff give "uncertain results" (being diplomatic) and you know sometimes you have only 1 shot (not talking about forensics *cough!*).
Definitive solution ? Buy professional equipment instead of $100 or $200 stuff. Then you'll discover that your recoverability success AND work quality will boost if not skyrocket, and also get customers that demand QUALITY instead of PRICE.
Unfortunately such equipment cost in the order of 10/20x the hobbyist stuff.
Think BIG if you want to be BIG

[Amarbir[CDR-Labs]]

Cheap chinese stuff give "uncertain results" (being diplomatic) and you know sometimes you have only 1 shot (not talking about forensics *cough!*).
Definitive solution ? Buy professional equipment instead of $100 or $200 stuff. Then you'll discover that your recoverability success AND work quality will boost if not skyrocket, and also get customers that demand QUALITY instead of PRICE.
Unfortunately such equipment cost in the order of 10/20x the hobbyist stuff.
Think BIG if you want to be BIG

Well,
Some Times Back No One used to think anything higher then weller .Now i have so many friends in the computer repair industry with virtually zero error bga work on USd 2000 ~ 3000 Machines

[BlackST]

In fact 2000 is not 200. Did you try Metcal by a chance ?

[Amarbir[CDR-Labs]]

In fact 2000 is not 200. Did you try Metcal by a chance ?

BL ,
The Popular Brands Are Very Hard To Get Here .Same is With Metcal .Jovy RE7500 Seems To Be a Good Solution

[BlackST]

Nope. Express couriers ship everywhere, just order it from local representative. Should be also possible to buy training. Here is no problem, at least. The real issue is the cost , that is not justifiable if the target are low budget low end jobs/customers (this problem is going to short circuit but the discussion would be much more OT).

[Amarbir[CDR-Labs]]

Nope. Express couriers ship everywhere, just order it from local representative. Should be also possible to buy training. Here is no problem, at least. The real issue is the cost , that is not justifiable if the target are low budget low end jobs/customers (this problem is going to short circuit but the discussion would be much more OT).

@ all,
is it me and bl having this discussion only or some of you can join in guys

[crecomp]

i have been using PDR for a while, very good tool cant fault it, makes easy work for any kind of chip

[BlackST]

Everything depend on how many jobs you do a day/week and how much disservice you can tolerate without your tool... Just this.

[Amarbir[CDR-Labs]]

i have been using PDR for a while, very good tool cant fault it, makes easy work for any kind of chip

Damn Good ,
Which Model Is That

[crecomp]

Will be back at work on Tuesday and will pm you

[angesxiao]

Everything depend on how many jobs you do a day/week and how much disservice you can tolerate without your tool...
i agree with BlackST.

[Amarbir[CDR-Labs]]

Everything depend on how many jobs you do a day/week and how much disservice you can tolerate without your tool...
i agree with BlackST.

Well,
I disagree 100% on This .Each BGA Rework station takes time to get used to ,All work From the cheapest to the most expensive once .But you have to do your own R&D to make it work .

[BlackST]

Then you have too much time at your disposal...

[angesxiao]

Everything depend on how many jobs you do a day/week and how much disservice you can tolerate without your tool...
i agree with BlackST.

Well,
I disagree 100% on This .Each BGA Rework station takes time to get used to ,All work From the cheapest to the most expensive once .But you have to do your own R&D to make it work .

thanks , i will

[Xavior007]

Okay, well apparently the approvers of posts with links are overwhelmed with requests so I will pose my question without the link to avoid the approval process. Looking into a BGA rework station, has anyone ever used this one SMTmax IR-6000 Dark Infrared BGA Rework Station? Its $1700 which is ok for me but I just need one that is simple to use and I will only use it on hard drive PCB's. Thanks all.

[harddriverecovery]

Well,
Some Times Back No One used to think anything higher then weller .Now i have so many friends in the computer repair industry with virtually zero error bga work on USd 2000 ~ 3000 Machines

Sorry, but is this even a human being posting this? If it's some kind of translation program, time for a new one!

[northwind]

I say you'd better show some more respect to people whose native language is other than english.