HELP ME NOT F3 prompt

[galaxy]

Boot 0x10M

Spin Up[0x00000000][0x0000B67C][0x0000BA10]
Trans.

Rst 0x10M

MC Internal LPC Process
Spin Up

(P) SATA Reset

[galaxy]

Model st500dm002 FIRMWARE-KC45

[labtech]

That's normal in some drives.

[galaxy]

any suggestion

[galaxy]

hard drive not show in bios (Bsy)

[galaxy]

help me Spildit where is short Read/ Write channel i Need data its very urgent

[galaxy]

After setting the COM and select the correct baud rate-38400, and ctrl+z, we couldn’t enter the F3 T>

[jerovsek]

try to unscrew pcb and isolate motor contacts with paper
power on and try with ctrl+z to reach F3 T>

and report

[jerovsek]

check this
viewtopic.php?f=1&t=26966&hilit=st500dm002
viewtopic.php?f=1&t=28343&hilit=st500dm002

[galaxy]

try to unscrew pcb and isolate motor contacts with paper
power on and try with ctrl+z to reach F3 T>

and report

[galaxy]

Boot 0x10M

Spin Up
FAIL Servo Op=0100 Resp=0003
ResponseFrame FFFF 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 FFFF
FAIL Servo Op=0100 Resp=0003
ResponseFrame 2EA0 0603 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000
FAIL Servo Op=0100 Resp=0003
ResponseFrame 2EA0 0603 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000
FAIL Servo Op=0100 Resp=0003
ResponseFrame 2EA0 0603 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000
FAIL Servo Op=0100 Resp=0003
ResponseFrame 2EA0 0603 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000
FAIL Servo Op=0100 Resp=0003
ResponseFrame 2EA0 0603 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000
FAIL Servo Op=0100 Resp=0003
ResponseFrame 2EA0 0603 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000
FAIL Servo Op=0100 Resp=0003
ResponseFrame 2EA0 0603 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000
FAIL Servo Op=0100 Resp=0003
ResponseFrame 2EA0 0603 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000
FAIL Servo Op=0100 Resp=0003
ResponseFrame 2EA0 0603 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000
FAIL Servo Op=0100 Resp=0003
ResponseFrame 2EA0 0603 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000




after the unscrew pcb and isolate motor contacts with paper
power on and try with ctrl+z to reach F3 T>

[lcoughey]

help me Spildit where is short Read/ Write channel i Need data its very urgent

If data is important, send to a pro who has the right tools and knowledge to safely recover your files. The more time you spend screwing around, the longer it will take for you to get your data back...plus any mistakes you make could make the cost to recover those files more expensive.