7200.12 ST3320418AS BUSY - SYS not accessible via serial
February 4th, 2017, 17:51
Hi,
i have this drive stuck in busy state.
I try translator regen, but i always get error (with every translator command that i send).
I can't even access to SYS files via serial port, i always get 'serial port error timeout'.
Motor spins good, no head clicking, good calibration sound
How to fix this problem?
NO DATA NEEDED
i have this drive stuck in busy state.
I try translator regen, but i always get error (with every translator command that i send).
I can't even access to SYS files via serial port, i always get 'serial port error timeout'.
Motor spins good, no head clicking, good calibration sound
- Code:
Rst 0x10M
Servo Processor Is Reset.
RW: Disc Ctlr Initialization Completed.
ExecuteSpinRequest
ASCII Diag mode
F3 T>
ASCII Diag mode
F3 T>
ATA 15 Cmds
Ts(ms) dT(ms) Op Cnt LBA
0 99999999 00 0000 000000000000
0 0 00 0000 000000000000
0 0 00 0000 000000000000
0 0 00 0000 000000000000
0 0 00 0000 000000000000
0 0 00 0000 000000000000
0 0 00 0000 000000000000
0 0 00 0000 000000000000
0 0 00 0000 000000000000
0 0 00 0000 000000000000
0 0 00 0000 000000000000
0 0 00 0000 000000000000
0 0 00 0000 000000000000
0 0 00 0000 000000000000
0 0 00 0000 000000000000
RW 32 Cmds
Ts(ms) dT(ms) xT(ms) Type Option Mode St EC Info
4294967295 99999999 4294705152 FF DFFFFFFF 7FDFFFFF FF FEFFFBFF
2139092991 2139092992 2088765440 FE FEEEFBEF FFFFFEFD FB 7FF3FFFF
4294967295 2155874304 0 FF FDFFFFFF 7FFFFFFF BF FFFDFFFF
4286570495 4286570496 6029312 FF DFFFFFFF FFFFFFFF FF FFFFFFFF
4160618495 4169015296 2281832448 FF FFFFE7F7 FFFEFFFD FF FFFFEFFE
4294967295 134348800 4294955000 DD FFFFFFFF FFFFEBFF DF FFBF7BEF
4261410815 4261410816 33556416 FF FFFCFFF7 7FFFFFF7 0 04005000
0 33556481 16777216 00 100002 202000 0 08000008 SEEK RD USR PBA B 000000000004 L 00000000
0 0 3 00 040900 001000 20 00080002 SEEK CRT LBA
16896 16896 134331904 00 8000000 2000808 0 00280000 SEEK RD USR LBA
262400 245504 4294704900 00 000440 8400004 0 00400200 SEEK CMP SYS LBA
0 4294704896 2 20 1004004 400200 0 00000100 RELD_RAP
8 8 570425336 00 10000200 80000100 0 00000000 SEEK RD USR LBA
4194304 4194296 4290772992 04 000000 000000 0 00040800 SRV_MEM Type 80 Addr 04002000 Cnt 0200
0 4290772992 0 08 40000010 091004 4 00005800 CAL
33849348 33849348 4261150724 00 094008 500120 0 00021000 SEEK RD USR TRK CHS 000080.0.0000 L 00200418
0 4261117948 0 10 000880 000000 1 20040002 GET_RVFF
397312 397312 4294586368 00 000000 40080000 0 00010000 SEEK RD USR LBA
1048576 651264 4294443008 40 004001 00800C 0 00000800 TWK_WR_PWR
1025 4293919745 4294966271 00 40000000 10900000 0 00000000 SEEK RD USR LBA
512 4294966783 33553921 00 20080000 9004060 4 40000021 SEEK RD USR LBA
1422 910 3772 2F 000000 000000 1 00000080 SPN_UP NORMAL
5194 3772 15 34 000000 000000 1 00000080 TCC 0
5210 16 21 02 002241 000000 1 00000080 XFR RD SYS LBA B 000000000000 L 00000004 BO 000000 BES 00E9C76.00E9E75.00E9C76
5231 21 267 02 002241 000000 2 43110081 XFR RD SYS LBA B 000000025CB4 L 00000004 BO 000000 BES 00E9C76.00E9E75.00E9C76
5498 267 2257 02 002241 000000 2 C4090082 XFR RD SYS LBA B 000000025CB4 L 00000001 BO 000000 BES 00E9C76.00E9E75.00E9C76
7761 2263 42 02 002241 000000 0 89800094 XFR RD SYS LBA B 000000008A0C L 000000C8 BO 000000 BES 006207E.006847D.006207E
7804 43 4 02 005041 000000 1 00000080 XFR WR SYS LBA B 0000000075AA L 00000001 BO 000000 BES 0061A7E.0061AFD.0061A7E
7809 5 2 02 005041 000000 1 00000080 XFR WR SYS LBA B 0000000055B4 L 00000008 BO 000000 BES 0061BFE.0061FFD.0061BFE
7811 2 8 02 005041 000000 1 00000080 XFR WR SYS LBA B 00000002B268 L 00000008 BO 000000 BES 0061BFE.0061FFD.0061BFE
7820 9 882 02 005041 000000 0 89800094 XFR WR SYS LBA B 0000000055B4 L 00000008 BO 000000 BES 0061BFE.0061FFD.0061BFE
8703 883 8 02 005041 000000 1 00000080 XFR WR SYS LBA B 00000002B268 L 00000008 BO 000000 BES 0061BFE.0061FFD.0061BFE
ASCII Diag mode
F3 T>m0,2,2,,,,,22
DiagError 0000500E Process Defect List Error
R/W Sense 00000002, R/W Error 841C0087, List Offset 00000000, List Index 00253BD3, File Error 000000D0
F3 T>
How to fix this problem?
NO DATA NEEDED
Re: 7200.12 ST3320418AS BUSY - SYS not accessible via serial
February 4th, 2017, 19:00
Seem to be working something now 
work in progress...
MRT i think doesn't have such option
work in progress...
MRT i think doesn't have such option
Re: 7200.12 ST3320418AS BUSY - SYS not accessible via serial
February 4th, 2017, 19:04
OK, now is ready again
Sediv has a lot more stuff than MRT that can help on this type of case
Sediv has a lot more stuff than MRT that can help on this type of case
- Attachments
-
Re: 7200.12 ST3320418AS BUSY - SYS not accessible via serial
February 4th, 2017, 20:16
- Code:
Rst 0x10M
Servo Processor Is Reset.
RW: Disc Ctlr Initialization Completed.
ExecuteSpinRequest
(P) SATA Reset
ASCII Diag mode
F3 T>
ATA 15 Cmds
Ts(ms) dT(ms) Op Cnt LBA
0 99999999 00 0000 000000000000
0 0 00 0000 000000000000
0 0 00 0000 000000000000
0 0 00 0000 000000000000
0 0 00 0000 000000000000
0 0 00 0000 000000000000
0 0 00 0000 000000000000
0 0 00 0000 000000000000
0 0 00 0000 000000000000
0 0 00 0000 000000000000
0 0 00 0000 000000000000
0 0 00 0000 000000000000
0 0 00 0000 000000000000
0 0 00 0000 000000000000
0 0 00 0000 000000000000
RW 32 Cmds
Ts(ms) dT(ms) xT(ms) Type Option Mode St EC Info
4692 99999999 9 02 002241 000000 1 00000080 XFR RD SYS LBA B 0000000055C4 L 00000009 BO 000000 BES 006ED80.006F1FF.006ED80
4704 12 0 42 002241 000000 1 00000080 SWD
4713 9 4 02 005041 000000 1 00000080 XFR WR SYS LBA B 0000000055B4 L 00000008 BO 000000 BES 0061BFE.0061FFD.0061BFE
4718 5 8 02 005041 000000 1 00000080 XFR WR SYS LBA B 00000002B268 L 00000008 BO 000000 BES 0061BFE.0061FFD.0061BFE
4726 8 3 02 002241 000000 1 00000080 XFR RD SYS LBA B 0000000060A4 L 00000006 BO 000000 BES 006D800.006DAFF.006D800
4729 3 2 02 002241 000000 1 00000080 XFR RD SYS LBA B 0000000075AA L 00000001 BO 000000 BES 0061A7E.0061AFD.0061A7E
4731 2 4 02 002241 000000 1 00000080 XFR RD SYS LBA B 000000008E55 L 00000001 BO 000000 BES 006D800.006DCFF.006D800
4736 5 4 02 005041 000000 1 00000080 XFR WR SYS LBA B 0000000075AA L 00000001 BO 000000 BES 0061A7E.0061AFD.0061A7E
4740 4 9 02 002241 000000 1 00000080 XFR RD SYS LBA B 000000009067 L 00000014 BO 000000 BES 00C17F6.02FFFFF.00C17F6
4750 10 6 02 002241 000000 1 00000080 XFR RD SYS LBA B 0000000075AB L 00000001 BO 000000 BES 00618FE.006197D.00618FE
4756 6 4 02 002241 000000 1 00000080 XFR RD SYS LBA B 000000008E54 L 00000001 BO 000000 BES 006D800.006DCFF.006D800
4761 5 8 02 005041 000000 1 00000080 XFR WR SYS LBA B 000000008E54 L 00000001 BO 000000 BES 006D800.006D87F.006D800
4769 8 8 02 005041 000000 1 00000080 XFR WR SYS LBA B 00000002EB08 L 00000001 BO 000000 BES 006D800.006D87F.006D800
4777 8 10 02 002241 000000 0 43110081 XFR RD SYS LBA B 0000000060A4 L 00000006 BO 000000 BES 006D800.006DAFF.006D800
4787 10 9 02 005041 000000 1 00000080 XFR WR SYS LBA B 0000000060A4 L 0000000A BO 000000 BES 006D800.006DCFF.006D800
4796 9 5 02 005041 000000 1 00000080 XFR WR SYS LBA B 0000000055B4 L 00000008 BO 000000 BES 0061BFE.0061FFD.0061BFE
4801 5 8 02 005041 000000 1 00000080 XFR WR SYS LBA B 00000002B268 L 00000008 BO 000000 BES 0061BFE.0061FFD.0061BFE
4809 8 0 27 005041 000000 1 00000080 SND_SRV 0C01 0000 0000 0000 0000 0000 0000 0000 0001 D289 00D0
0D5C 0400 0000 000B 0002 F580 F240 0000 10A2 0000 0000 0000 0000 0000 0000 0000
4815 6 11 02 002241 000000 1 00000080 XFR RD SYS LBA B 000000008A0C L 000000C8 BO 000000 BES 006207E.006847D.006207E
4830 15 5 02 002241 000000 1 00000080 XFR RD SYS LBA B 000000008E63 L 00000002 BO 000000 BES 006D800.006DCFF.006D800
4836 6 8 02 005041 000000 1 00000080 XFR WR SYS LBA B 000000008E63 L 00000002 BO 000000 BES 006D800.006D8FF.006D800
4844 8 8 02 005041 000000 1 00000080 XFR WR SYS LBA B 00000002EB17 L 00000002 BO 000000 BES 006D800.006D8FF.006D800
4852 8 8 02 002241 000000 1 00000080 XFR RD SYS LBA B 000000008E63 L 00000002 BO 000000 BES 00C17F6.02FFFFF.00C17F6
4861 9 4 02 005041 000000 1 00000080 XFR WR SYS LBA B 0000000075AA L 00000001 BO 000000 BES 0061A7E.0061AFD.0061A7E
4865 4 5 02 002241 000000 1 00000080 XFR RD SYS LBA B 0000000060A4 L 00000006 BO 000000 BES 006D800.006DAFF.006D800
4871 6 8 02 005041 000000 1 00000080 XFR WR SYS LBA B 0000000060A4 L 0000000A BO 000000 BES 006D800.006DCFF.006D800
4879 8 9 02 002241 000000 1 00000080 XFR RD SYS LBA B 0000000060E8 L 00000001 BO 000000 BES 006015F.00601DE.006015F
4888 9 4 02 005041 000000 1 00000080 XFR WR SYS LBA B 0000000055B4 L 00000008 BO 000000 BES 0061BFE.0061FFD.0061BFE
4893 5 8 02 005041 000000 1 00000080 XFR WR SYS LBA B 00000002B268 L 00000008 BO 000000 BES 0061BFE.0061FFD.0061BFE
4902 9 0 47 000000 000000 1 00000080 DISC_SLIP
4902 0 8 02 005041 000000 1 00000080 XFR WR SYS LBA B 000000008E54 L 00000001 BO 000000 BES 006D800.006D87F.006D800
4911 9 7 02 005041 000000 1 00000080 XFR WR SYS LBA B 00000002EB08 L 00000001 BO 000000 BES 006D800.006D87F.006D800
ASCII Diag mode
F3 T>/7
F3 7>m100
OverlayCompatibilityCheck failed
Unable to load Diag Cmd Processor Overlay
F3 7>/
F3 T>V1
Unable to load Diag Cmd Processor Overlay
F3 T>V2
Unable to load Diag Cmd Processor Overlay
F3 T>V4
Unable to load Diag Cmd Processor Overlay
F3 T>V8
Unable to load Diag Cmd Processor Overlay
F3 T>V10
Unable to load Diag Cmd Processor Overlay
F3 T>V40
Unable to load Diag Cmd Processor Overlay
F3 T>V80
Unable to load Diag Cmd Processor Overlay
F3 T>
something is still wrong, i still can't access into SYS file even via serial port, but now drive gets ready when i power on
Re: 7200.12 ST3320418AS BUSY - SYS not accessible via serial
February 4th, 2017, 20:19
If i try to do anything in utility, it goes busy (but DRD and DSC flags stay on) and get LED CC error on terminal
- Code:
LED:000000CC FAddr:00287669
LED:000000CC FAddr:00287669
LED:000000CC FAddr:00287669
LED:000000CC FAddr:00287669
LED:000000CC FAddr:00287669
LED:000000CC FAddr:00287669
LED:000000CC FAddr:00287669
LED:000000CC FAddr:00287669
LED:000000CC FAddr:00287669
LED:000000CC FAddr:00287669
LED:000000CC FAddr:00287669
LED:000000CC FAddr:00287669
LED:000000CC FAddr:00287669
LED:000000CC FAddr:00287669
LED:000000CC FAddr:00287669
LED:000000CC FAddr:00287669
LED:000000CC FAddr:00287669
LED:000000CC FAddr:00287669
Re: 7200.12 ST3320418AS BUSY - SYS not accessible via serial
February 4th, 2017, 20:34
OK, i uploaded LDR with MRT, now i can access to SYS. I'm writing back original SYS from backup
P.S.
I had backup LDR from this drive before i started to play with 2 weeks ago.
P.S.
I had backup LDR from this drive before i started to play with 2 weeks ago.
Re: 7200.12 ST3320418AS BUSY - SYS not accessible via serial
February 4th, 2017, 20:44
ok i will test LDRs on both tool, the reason why i'm working again with MRT is because i've an older sediv version than yours, which i think doesn't support sys writing (i still have to activate the last version).
I will check this too when i get back on sediv system (tomorrow).
Thank you, now i'm going to sleep.
I will check this too when i get back on sediv system (tomorrow).
Thank you, now i'm going to sleep.
Re: 7200.12 ST3320418AS BUSY - SYS not accessible via serial
February 5th, 2017, 19:25
My last sediv version is 5.1.6.20 and does support SYS (read and write).
Sediv seem supporting MRT loader file, this is good.
I'm doing some experiments on this drive now, i let you know more soon, thank you.
Sediv seem supporting MRT loader file, this is good.
I'm doing some experiments on this drive now, i let you know more soon, thank you.
February 6th, 2017, 11:48
Yes, my sediv version supports reading/writing SYS only via ATA. I should update it so that i will be able to 'play' with SYS also in serial mode.
I wrote back all tracks by using MRT (sediv doesn't have utility for read/write tracks).
At this time i wrote into SA 0 all tracks that i have backup at beginning (i mean when the drive didn't have yet LBA limited access problem) from SA 1.
Then i started surface scan, i couldn't access into first sectors, but i can access into sectors afterwards until the last LBA (this means that limited LBA access is fixed) but there are further problems...
I did clear G-list (NG was already empty), then i started zero fill but when erase finished i found again a lot of g-list entries, so this means that drive has surface damages or weak heads (or both).
I made a video for you Spildit (and of course for everyone who want to see it) to show you that the drive has physical problems.
I think heads are good but there are a lot of damaged zones, expecially on surface 0
http://www.mediafire.com/file/nla002e2h ... th_MRT.wmv
I wrote back all tracks by using MRT (sediv doesn't have utility for read/write tracks).
At this time i wrote into SA 0 all tracks that i have backup at beginning (i mean when the drive didn't have yet LBA limited access problem) from SA 1.
Then i started surface scan, i couldn't access into first sectors, but i can access into sectors afterwards until the last LBA (this means that limited LBA access is fixed) but there are further problems...
I did clear G-list (NG was already empty), then i started zero fill but when erase finished i found again a lot of g-list entries, so this means that drive has surface damages or weak heads (or both).
I made a video for you Spildit (and of course for everyone who want to see it) to show you that the drive has physical problems.
I think heads are good but there are a lot of damaged zones, expecially on surface 0
http://www.mediafire.com/file/nla002e2h ... th_MRT.wmv
Re: 7200.12 ST3320418AS BUSY - SYS not accessible via serial
February 6th, 2017, 14:25
yes, i think we have to disable bad zones.
I don't know if my sediv version has option to cut zones, but mrt should have it.
I will try to cut bad zones with mrt, you might try with sediv
I don't know if my sediv version has option to cut zones, but mrt should have it.
I will try to cut bad zones with mrt, you might try with sediv
Powered by phpBB © phpBB Group.