western digital PCB repair SATA FUSE .. help me to clarify

[Data-Salvage]

Hello guys
does somebody know the voltage of this two fuses?
i tried to find on aliexpress but all seller tell me the ampere but they dont know the voltage ..
i believe is 1206 size.. left is 5v right is 12v... how come is same sizes but different voltage?
for now i managed to find same sizes fuses with letter O in the center... is this safe to use or should i replace them?
sorry for bothering....im a beginner

God bless you all

Attachments

fuses 2.jpg (57.5 KiB) Viewed 34089 times

[SWM]

The sellers are right to ask about the current.
If you have the letter S there, the fuses are 4 amps.
The breakdown voltage depends on the size, nominal value and material.
https://docs.rs-online.com/aae3/0900766b80785544.pdf

[Data-Salvage]

The sellers are right to ask about the current.
If you have the letter S there, the fuses are 4 amps.
The breakdown voltage depends on the size, nominal value and material.
https://docs.rs-online.com/aae3/0900766b80785544.pdf

Sir thank you however mine are different type of FUSE
still not clear why the fuses on my PCB has same szes but measure 5v and 12v... i need to figure out what are this fuses

Attachments

[fzabkar]

Sir thank you however mine are different type of FUSE
still not clear why the fuses on my PCB has same szes but measure 5v and 12v... i need to figure out what are this fuses

If you have the letter S there, the fuses are 4 amps.

Current and voltage are not the same thing. A 5V supply can deliver 4A, as can a 12V supply.

[Data-Salvage]

Sir thank you however mine are different type of FUSE
still not clear why the fuses on my PCB has same szes but measure 5v and 12v... i need to figure out what are this fuses

If you have the letter S there, the fuses are 4 amps.

Current and voltage are not the same thing. A 5V supply can deliver 4A, as can a 12V supply.

Thank you Sir which means 5v and 12 are not the same fuse even if they got the same sizes ?

[SWM]

Yes, there are two 4A fuses in the picture.

[Data-Salvage]

Yes, there are two 4A fuses in the picture.

thank you sir! are thos 1026 4a?

[Data-Salvage]

iv changed the fuses and all component from donor pcb but the 12v line still doesnt work.
i suspect he controller is dead..... mean i lost the data right? is there a way to find out the controller condition? this is what i get in pc-3000 portable

Attachments

Healthy PCB.JPG (6.01 KiB) Viewed 33400 times

[Data-Salvage]

iv changed the fuses and all component from donor pcb but the 12v line still doesnt work.
i suspect he controller is dead..... mean i lost the data right? is there a way to find out the controller condition? this is what i get in pc-3000 portable

healthy PCB

[Data-Salvage]

Dead PCB

Attachments

Dead PCB.JPG (7.29 KiB) Viewed 33399 times

[sin]

please show status registers too.

[SWM]

You checked the diodes after the fuses for short circuits, right?..

[Data-Salvage]

You checked the diodes after the fuses for short circuits, right?..

i replaced diodes and fuses aswell

[Data-Salvage]

please show status registers too.

looks like nothing is connected in the status

[SWM]

Well, all hope is on Frank...
If your qualifications allow, you can measure the voltages after the converters on the board yourself.
Judging by the lack of current at 12V, the spinner chip burned out. But not 100%.
If yes, there is a high probability of damage to the preamplifier.

[Data-Salvage]

Well, all hope is on Frank...
If your qualifications allow, you can measure the voltages after the converters on the board yourself.
Judging by the lack of current at 12V, the spinner chip burned out. But not 100%.
If yes, there is a high probability of damage to the preamplifier.

thank you Sir^^ who is frank?

is the spinner chip the one inside the red circle?
iv noticed the little guy inside the blue circle make the multimeter beebs in diode mode

Attachments

[SWM]

Well, all hope is on Frank...
who is frank?

fzabkar

[Data-Salvage]

Well, all hope is on Frank...
who is frank?

fzabkar

i made him angry because of my beginner questions... and i understand he is very busy person

[Data-Salvage]

guys i made a comparison of the healthy and broken pcb
first image is health pcb

Attachments

[Data-Salvage]

and now the broken PCB it beeps alot. iv replace the BEEPING filter with healthy filter but same ... could it be dead controller? or dead SMOOTH spindle controller? or both?? please help im still a beginer

Attachments