PCB Board For Barracuda 7200.7 200GB
March 8th, 2007, 5:31
Hi Friends,
my name is Andy from Indonesia. I'm looking for any seller that might have this following PCB board for my hard disk. Below is my drive's specifications:
Seagate Barracuda 7200.7
200 Gbytes (Parallel ATA)
Model : ST3200822A
P/N : 9W2844-301
HDA P/N : 100314751
Config : A5C-08
Firmware : 3.01
Site Code : TK
(Product of Thailand)
One component was burnt because of power failure. I'm pretty sure that the inside of the drive is ok (hopefully)
It's full of my families digital photos, will take ages for me to scan it one by one. Looking forward for replies...and thank you.
Cheers,
Andy
my name is Andy from Indonesia. I'm looking for any seller that might have this following PCB board for my hard disk. Below is my drive's specifications:
Seagate Barracuda 7200.7
200 Gbytes (Parallel ATA)
Model : ST3200822A
P/N : 9W2844-301
HDA P/N : 100314751
Config : A5C-08
Firmware : 3.01
Site Code : TK
(Product of Thailand)
One component was burnt because of power failure. I'm pretty sure that the inside of the drive is ok (hopefully)
It's full of my families digital photos, will take ages for me to scan it one by one. Looking forward for replies...and thank you.
Cheers,
Andy
.....
March 9th, 2007, 21:24
which component?
March 12th, 2007, 0:53
Hi gsimon,
thank you for your reply.
Actually I don't know what it is called. It's a small black "thing" with 2 connectors on it. Becam a bit ugly in shape (that's where the smoke came out). So I think I will need to replace the whole board. Do you have any idea where I can find it?
thank you for your reply.
Actually I don't know what it is called. It's a small black "thing" with 2 connectors on it. Becam a bit ugly in shape (that's where the smoke came out). So I think I will need to replace the whole board. Do you have any idea where I can find it?
March 12th, 2007, 4:15
Hi,
that's probably the TVS, it become shorted by a power surge.
try desoldering it and power the drive afterwards to see if it works (probably it will).
pepe
that's probably the TVS, it become shorted by a power surge.
try desoldering it and power the drive afterwards to see if it works (probably it will).
pepe
March 21st, 2007, 0:54
Hi pepe,
thank you for your reply. Can Iask you what TVS stans for? I'm not familiar with electronic components..Thanks in advance...
thank you for your reply. Can Iask you what TVS stans for? I'm not familiar with electronic components..Thanks in advance...
March 21st, 2007, 13:08
Hi,
Transient Voltage Suppressor.
But in this case it might not be the best solution for you to touch the board...
pepe
Transient Voltage Suppressor.
I'm not familiar with electronic components..Thanks in advance...
But in this case it might not be the best solution for you to touch the board...
pepe
Re: PCB Board For Barracuda 7200.7 200GB
March 23rd, 2007, 12:37
DyWaN wrote:Hi Friends,
my name is Andy from Indonesia. I'm looking for any seller that might have this following PCB board for my hard disk. Below is my drive's specifications:
Seagate Barracuda 7200.7
200 Gbytes (Parallel ATA)
Model : ST3200822A
P/N : 9W2844-301
HDA P/N : 100314751
Config : A5C-08
Firmware : 3.01
Site Code : TK
(Product of Thailand)
One component was burnt because of power failure. I'm pretty sure that the inside of the drive is ok (hopefully)
Cheers,
Andy
Dear dyWan
Please contact me, PRSESAWI@YAHOO.COM. because i live In Indonesia
Powered by phpBB © phpBB Group.