ST3200822A (Many bads blocks)

[sempre]

Hi to all!

Please opnion the case!

Necessary date recovery of this hdd, already I tried DE PCI, MEDIA TOOL PRO for data among others recovery and to clone this hdd but without success, somebody already had some here in case that seemed, can give to its opinon?

[PRE]HDD: ST3200822A; FW: 3.01;
--------------------------------------------------------
Name Val Worst Raw
Att # 1 : Read error rate : 52 44 197396991
Att # 3 : Spin up time : 98 96 0
Att # 4 : Number of spin-up times : 100 100 396
Att # 5 : Reallocated sectors count : 89 89 474
Att # 7 : Seek error rate : 86 60 450771832
Att # 9 : Power-on time : 65 65 31182
Att # 10 : Spin-up retries : 100 100 0
Att # 12 : Start/stop count : 100 100 885
Att # 194 : HDA Temperature : 32 55 32
Att # 195 : Hardware ECC recovered : 52 44 197396991
Att # 197 : Current pending sectors : 100 100 540
Att # 198 : Offline scan UNC sectors : 100 100 540
Att # 199 : Ultra ATA CRC Error Rate : 200 187 13
Att # 200 : Write error rate : 100 253 0
Att # 202 : Unknown : 48 201 52


Thanks advance!

[beto]

What did u got on terminal? u could post us the screenshot from mhdd

regards

[BlackST]

Degraded head? Maybe a selfscan...

[ccc]

"Maybe a selfscan"????? .......He needs the data!!!!

[hddguy]

Necessary date recovery of this hdd, already I tried DE PCI, MEDIA TOOL PRO for data among others recovery and to clone this hdd but without success, somebody already had some here in case that seemed, can give to its opinon?

Why was it unsuccessful? Was there any successfull reading of any sectors at all?

[sempre]

Degraded head? Maybe a selfscan...

I believe that the friend did not read post all!

Thanks...

[sempre]

Necessary date recovery of this hdd, already I tried DE PCI, MEDIA TOOL PRO for data among others recovery and to clone this hdd but without success, somebody already had some here in case that seemed, can give to its opinon?

Why was it unsuccessful? Was there any successfull reading of any sectors at all?

Hi hddguy!

it does not obtain to read the bad sectors nor with 30 attempts in bad sectors and hdd stops to answer the commands…

Thanks..

[ccc]

Please post terminal report.....

Rgds

[BlackST]

OK I forgot it was a DR case.... OK OK
Yes, terminal log is a little more useful

[sempre]

What did u got on terminal? u could post us the screenshot from mhdd

regards

Hi Beto, ccc and others..

look log term

Interface task reset
4096k x 16 buffer detected
APLUS - 1_Disk S.07 01-17-04 11:37

Buzz - Head Mask FFFF - Switch to full int.
Spin Ready
3.01 01-17-04 11:39
(P)PATA Reset
Master
(S)PATA Reset
Master
(H)PATA Reset
Master
AT Er 00 Nwt Er 49 RdWr 00091.02.00f2
ATA St 50 Er 01 Op 00 0,0000/0/00,00 01 00
Niwot: ec45346b ff ec45346b.0.033 0033 408e 0001 00c7

CE Log EC=49 Rtype=26 OV=0 STStatus0
Not handled software path:

[sempre]

Hi, No opinion??

[Doomer]

AT Er 00 Nwt Er 49 RdWr 00091.02.00f2
ATA St 50 Er 01 Op 00 0,0000/0/00,00 01 00
Niwot: ec45346b ff ec45346b.0.033 0033 408e 0001 00c7

CE Log EC=49 Rtype=26 OV=0 STStatus0
Not handled software path: <---

The read error parser cause firmware hang
It is pretty common for APLUS and ALPINE models

[beto]

u can tried a head test by terminal, to know if its MHA problem

Regards

[sempre]

Please Look
log

Attachments

log.rar

(2.63 KiB) Downloaded 312 times

[sempre]

DATA RECOVERY SUCESS!!!!!

[drc]

How did you fix it?

[Amarbir[CDR-Labs]]

DATA RECOVERY SUCESS!!!!!

Well Sempre ,
What Was Wrong ,You Should Definitely Post cos the essence of the thread is Gone when you Do Not