MultiDrive – free backup, clone & wipe disk utility from Atola Technology

Main » Forums home » Conventional hard drives

All times are UTC - 5 hours [ DST ]



Post new topic Reply to topic  Page 1 of 1
  [ 12 posts ] 
  Previous topic | Next topic 
Author Message
ddrecovery
 Post subject: Helium Filled Drives
PostPosted: December 11th, 2019, 14:03 
Offline
User avatar

Joined: June 11th, 2013, 17:01
Posts: 1773
Location: Phoenix, AZ USA
Anyone done much research on these drives in terms of head swaps?
Obviously we have several issues such as the sealed lid, helium, donor costs, locked FW etc etc.
I have a WD100 with stiction and am thinking of buying some donors to experiment with to see of head swap is actually possible.
Any information would be appreciated, and my findings will be shared.

_________________
HDD, SSD, Flash and RAID Data Recovery
Founder of The Data Recovery Professionals Group
Top
 Profile  
 
melvin
 Post subject: Re: Helium Filled Drives
PostPosted: December 11th, 2019, 15:18 
Offline
User avatar

Joined: September 16th, 2015, 9:06
Posts: 355
Location: Poland
Didn't find a way to open He drives without leaving a mess inside. Besides they will not work without He.

_________________
odzyskiwanie danych
Top
 Profile  
 
ddrecovery
 Post subject: Re: Helium Filled Drives
PostPosted: December 11th, 2019, 15:26 
Offline
User avatar

Joined: June 11th, 2013, 17:01
Posts: 1773
Location: Phoenix, AZ USA
melvin wrote:
Didn't find a way to open He drives without leaving a mess inside. Besides they will not work without He.

I have read reports that drives can be recovered without He. All depends on how much data the client has as the heads die after a while. There 'reports' could of course be covered in the delicate smell of bullshit.....

_________________
HDD, SSD, Flash and RAID Data Recovery
Founder of The Data Recovery Professionals Group
Top
 Profile  
 
fzabkar
 Post subject: Re: Helium Filled Drives
PostPosted: December 11th, 2019, 16:00 
Offline
User avatar

Joined: September 8th, 2009, 18:21
Posts: 17215
Location: Australia
ISTR one thread where it was claimed that some models won't spin if the helium sensor reports a low He level.

Even if a head swap is achievable physically, I wonder whether the donor's head adaptives would need to be transferred to the patient's ROM. I have written a tool to extract these adaptives from HGST ROMs, but I haven't been able to work out the CRC algorithm. I know that some technical information has leaked into the DR community, but I haven't seen it.

_________________
A backup a day keeps DR away.
Top
 Profile  
 
northwind
 Post subject: Re: Helium Filled Drives
PostPosted: December 12th, 2019, 6:34 
Offline
User avatar

Joined: January 28th, 2009, 10:54
Posts: 3550
Location: Greece
We've done some tests, they all failed :(

Even if you manage to cut open the lid (we used laser) without making a mess, and solve the He problem (we didn't, we just wanted to see if the drive will spin up and calibrate after a head change) and you unlock the FW (which, to the best of my knowledge is not viable at this moment), you need to make the new heads boot up. And, at least to our test, they didn't.
Most probably due to the adaptives Frank is referring to.
The drive DID spin up without He, though.

_________________
http://www.northwind.gr
SandForce SSD Recovery
Ransomware Reverse Engineering - NoMoreRansom! partners
Top
 Profile  
 
ddrecovery
 Post subject: Re: Helium Filled Drives
PostPosted: December 12th, 2019, 10:59 
Offline
User avatar

Joined: June 11th, 2013, 17:01
Posts: 1773
Location: Phoenix, AZ USA
Thanks for the comments. I will report my findings as I progress.

_________________
HDD, SSD, Flash and RAID Data Recovery
Founder of The Data Recovery Professionals Group
Top
 Profile  
 
fzabkar
 Post subject: Re: Helium Filled Drives
PostPosted: December 12th, 2019, 12:06 
Offline
User avatar

Joined: September 8th, 2009, 18:21
Posts: 17215
Location: Australia
northwind wrote:
We've done some tests, they all failed :(

Even if you manage to cut open the lid (we used laser) without making a mess, and solve the He problem (we didn't, we just wanted to see if the drive will spin up and calibrate after a head change) and you unlock the FW (which, to the best of my knowledge is not viable at this moment), you need to make the new heads boot up. And, at least to our test, they didn't.
Most probably due to the adaptives Frank is referring to.
The drive DID spin up without He, though.

What if you replace the heads and PCB as a set, rather than transplanting the adaptives?

_________________
A backup a day keeps DR away.
Top
 Profile  
 
ddrecovery
 Post subject: Re: Helium Filled Drives
PostPosted: December 12th, 2019, 12:16 
Offline
User avatar

Joined: June 11th, 2013, 17:01
Posts: 1773
Location: Phoenix, AZ USA
fzabkar wrote:
What if you replace the heads and PCB as a set, rather than transplanting the adaptives?

I guess that might work if the patient SA and PCB are compatible. Impossible to know on these drives at the moment.

_________________
HDD, SSD, Flash and RAID Data Recovery
Founder of The Data Recovery Professionals Group
Top
 Profile  
 
jono-ats
 Post subject: Re: Helium Filled Drives
PostPosted: December 12th, 2019, 16:19 
Offline
User avatar

Joined: June 8th, 2006, 19:44
Posts: 3144
Location: Atlanta, GA
fzabkar wrote:

What if you replace the heads and PCB as a set, rather than transplanting the adaptives?


Not likely. I would imagine there are some platter adaptives that have to agree with the ROM. For example, in older HGST products, the NV-RAM (within ROM) points to a boot location on the media.

_________________
http://www.datasaversllc.com
Top
 Profile  
 
saltwater
 Post subject: Re: Helium Filled Drives
PostPosted: December 12th, 2019, 16:56 
Offline
User avatar

Joined: November 3rd, 2013, 13:04
Posts: 330
Location: Hungary
Without helium i think the air makes more turbulence and pressure than helium, and the heads can't fly on the calculated height. That's why HSA can't calibrate.
Top
 Profile  
 
fzabkar
 Post subject: Re: Helium Filled Drives
PostPosted: December 12th, 2019, 19:00 
Offline
User avatar

Joined: September 8th, 2009, 18:21
Posts: 17215
Location: Australia
jono-ats wrote:
I would imagine there are some platter adaptives that have to agree with the ROM. For example, in older HGST products, the NV-RAM (within ROM) points to a boot location on the media.

The only adaptive section that looks like it might point to SA cylinders (or zones ?) is the "CYL" component in the FSVS module. Otherwise there is nothing which looks like the old style "NVRAM". Of course ICBW.

Adaptive sections in FSVS module in HUH728080ALE604 ROM

Code:
size   ID    Description
-----  ----  ------------------------------------
  132  CYL
  108  KT
  172  TPCR  Track Pitch Correction params
    8  MFGF  Mfg Flags for Servo Manager
2,244  PES   Position Error Signal ?
  116  RWGP  Read/Write Gap table - microjogs
1,012  RW32
  344  RWTC
5,388  SWTG
   24  WIND
7,188  RRO2  Repeatable Runout ?
  456  ACDC   empty
  680  MACT  Microactuator normalization parameters
  260  MAFF  Microactuator feedforward ?
4,928  RRDC   empty
2,056  FLTS   empty

_________________
A backup a day keeps DR away.
Top
 Profile  
 
jono-ats
 Post subject: Re: Helium Filled Drives
PostPosted: December 13th, 2019, 12:22 
Offline
User avatar

Joined: June 8th, 2006, 19:44
Posts: 3144
Location: Atlanta, GA
fzabkar wrote:
jono-ats wrote:
I would imagine there are some platter adaptives that have to agree with the ROM. For example, in older HGST products, the NV-RAM (within ROM) points to a boot location on the media.

The only adaptive section that looks like it might point to SA cylinders (or zones ?) is the "CYL" component in the FSVS module. Otherwise there is nothing which looks like the old style "NVRAM". Of course ICBW.

Adaptive sections in FSVS module in HUH728080ALE604 ROM

Code:
size   ID    Description
-----  ----  ------------------------------------
  132  CYL
  108  KT
  172  TPCR  Track Pitch Correction params
    8  MFGF  Mfg Flags for Servo Manager
2,244  PES   Position Error Signal ?
  116  RWGP  Read/Write Gap table - microjogs
1,012  RW32
  344  RWTC
5,388  SWTG
   24  WIND
7,188  RRO2  Repeatable Runout ?
  456  ACDC   empty
  680  MACT  Microactuator normalization parameters
  260  MAFF  Microactuator feedforward ?
4,928  RRDC   empty
2,056  FLTS   empty


Good info. Thanks!

_________________
http://www.datasaversllc.com
Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  Page 1 of 1
  [ 12 posts ] 

Main » Forums home » Conventional hard drives

All times are UTC - 5 hours [ DST ]

Who is online

Users browsing this forum: Google [Bot], Majestic-12 [Bot] and 242 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Switch to mobile style
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group