MultiDrive – free backup, clone & wipe disk utility from Atola Technology

All times are UTC - 5 hours [ DST ]




Post new topic Reply to topic  [ 5 posts ] 
Author Message
 Post subject: Palmer ROM version 1.26N unlock?
PostPosted: July 3rd, 2026, 7:02 
Offline

Joined: September 14th, 2023, 8:43
Posts: 62
Location: Kentucky USA
Does anyone know how to unlock these ROMs? ACE Lab support says the utility cannot unlock the ROM properly. When using the unlocked ROM it spins in kernel mode but refuses to take any loaders.
Code:
Cache ovl(10) data uploading............ : Ok
Permanent ovl (11) data uploading Device Error Detected: "VSC ERR OFF TOO LARGE"
Statc Mdl writing error Device Error Detected: "VSC ERR INV FUNC CODE REQ"


Power up log looks normal?
Code:
NN | Step |   Time |           Flags |     Info | Mdl ID       | Description (64-bits)                             
----+------+--------+-----------------+----------+--------------+----------------------------------------------------
  0 |    1 | 377 ms |     40000000006 | ACE1A011 |              | MAIN_START +FLASH_CFG_OK +APB_OK                   
  1 |  111 | 378 ms |     40000000016 |    7E156 | 4F           | EXEC_POWERUP_LOAD_LATEST_FLSHD +SEAM_CALDATA_OK   
  2 |  112 | 1.31 s |     40000000016 |        0 |              | SERVO_CORE_START_REQUEST                           
  3 |  113 | 1.38 s |     40000000016 |        0 |              | SERVO_CORE_RUNNING                                 
  4 |  B00 | 1.38 s |     40000000016 |       30 |              | RESET_ISSUED                                       
  5 |  C06 | 1.38 s |     40000000016 |        0 |              | HOST_TASK_START                                   
  6 |  100 | 1.38 s |     40000000016 |        0 |              | EXEC_POWERUP_START                                 
  7 |  101 | 1.39 s |     40000000016 |        0 |              | EXEC_POWERUP_INITS                                 
  8 |  10F | 1.39 s |     40000000017 |        0 | 0B           | EXEC_POWERUP_READ_FLSH_DIR +FLASH_DIR_OK           
  9 |  103 | 1.39 s |     4000000001F |        0 | 47           | EXEC_POWERUP_LOAD_RC_OPTIMIZATION +RSVD_OPTDATA_OK
10 |  104 | 1.39 s |     4000000003F |        0 | 30           | EXEC_POWERUP_LOAD_RPDLIST +RPD_LIST_OK             
11 | 7107 | 1.39 s |               0 |      501 |              | SET_SOC_ACTIVE (PM_SOC_ACTIVE)                     
12 | 7107 | 1.39 s |               0 |      501 |              | SET_SOC_ACTIVE (PM_SOC_ACTIVE)                     
13 |  40D | 1.39 s |     4000000003F |        0 |              | SPINUP_LOW_LEVEL                                   
14 |  40B | 2.13 s |     4000000003F |        0 |              | GET_SPINUP_TIME                                   
15 |  405 | 2.58 s |     4000000003F |        0 |              | ACTUATOR_INIT                                     
16 |  410 | 2.58 s |     4000000003F |        0 |              | SPINUP_LOW_LEVEL                                   
17 |  105 | 2.60 s |     4000000007F |        0 | 01           | EXEC_POWERUP_LOAD_DIR_DATA +RSVD_AREA_DIR_OK       
18 |  114 | 2.63 s | 40004000000007F |        0 | D000 or D001 | EXEC_POWERUP_READ_LUT                             
19 |  118 | 2.64 s | 40004000000007F |        1 | 81/19E       | Load Overlay id81/id19E                           
20 |  107 | 2.70 s | 40004000000007F |        0 | 11           | EXEC_POWERUP_LOAD_PERMOVL                         
21 |  108 | 2.75 s | 40004000000007F |        0 | 11           | EXEC_POWERUP_VERIFY_PERMOVL                       
22 |  11D | 2.75 s | 40004000000007F |    4E9B8 |              | PWR act code 11D                                   
23 |  118 | 2.75 s | 40004000000007F |        1 | 81/19E       | Load Overlay id81/id19E                           
24 | 7107 | 2.75 s |               0 |      501 |              | SET_SOC_ACTIVE (PM_SOC_ACTIVE)                     
25 |  407 | 2.89 s | 40004000000007F |        0 |              | PARK                                               
26 |  C09 | 2.89 s | 40004000000007F |        0 |              | HOST_TASK_CALLBACK_EVENT                           
27 |  A00 | 2.89 s | 40004000000007F |      150 |              | HOST_POST_INIT_STATUS                             
28 |  B00 | 1.51 s | 40004000000007F |      119 |              | RESET_ISSUED                                       
29 |  C06 | 1.51 s | 40004000000007F |        0 |              | HOST_TASK_START                                   
30 |  100 | 1.51 s | 40004000000007F |        0 |              | EXEC_POWERUP_START                                 
31 | 7107 | 1.51 s |               0 |      501 |              | SET_SOC_ACTIVE (PM_SOC_ACTIVE)                     
32 | 7107 | 1.51 s |               0 |      501 |              | SET_SOC_ACTIVE (PM_SOC_ACTIVE)                     
33 |  405 | 2.02 s | 40004000000007F |        0 |              | ACTUATOR_INIT                                     
34 |  410 | 2.02 s | 40004000000007F |        0 |              | SPINUP_LOW_LEVEL                                   
35 |  118 | 2.02 s | 40004000000007F |        1 | 81/19E       | Load Overlay id81/id19E                           
36 |  107 | 2.10 s | 40004000000007F |        0 | 11           | EXEC_POWERUP_LOAD_PERMOVL                         
37 |  108 | 2.14 s | 40004000000007F |        0 | 11           | EXEC_POWERUP_VERIFY_PERMOVL                       
38 |  11D | 2.14 s | 40004000000007F |    4E9B8 |              | PWR act code 11D                                   
39 |  118 | 2.14 s | 40004000000007F |        1 | 81/19E       | Load Overlay id81/id19E                           
40 | 7107 | 2.14 s |               0 |      501 |              | SET_SOC_ACTIVE (PM_SOC_ACTIVE)                     
41 |  407 | 2.29 s | 40004000000007F |        0 |              | PARK                                               
42 |  C09 | 2.29 s | 40004000000007F |        0 |              | HOST_TASK_CALLBACK_EVENT                           
43 |  A00 | 2.31 s | 40004000000007F |      150 |              | HOST_POST_INIT_STATUS                             
----+------+--------+-----------------+----------+--------------+----------------------------------------------------
FLASH_DIR_OK FLASH_CFG_OK APB_OK RSVD_OPTDATA_OK SEAM_CALDATA_OK RPD_LIST_OK RSVD_AREA_DIR_OK


Attachments:
File comment: ROM
palmer.zip [644.28 KiB]
Downloaded 37 times
Top
 Profile  
 
 Post subject: Re: Palmer ROM version 1.26N unlock?
PostPosted: July 6th, 2026, 11:04 
Offline

Joined: April 25th, 2025, 10:22
Posts: 12
Location: italy
Pcb model?

_________________
Italia Assistance Data Recovery
Italian data recovery lab – HDD, SSD, NAS, RAID
Professional data recovery lab


Top
 Profile  
 
 Post subject: Re: Palmer ROM version 1.26N unlock?
PostPosted: July 6th, 2026, 11:56 
Offline

Joined: January 2nd, 2024, 8:38
Posts: 3
Location: Austria
try this..


Attachments:
palmer-unlock.zip [646.24 KiB]
Downloaded 19 times
Top
 Profile  
 
 Post subject: Re: Palmer ROM version 1.26N unlock?
PostPosted: July 6th, 2026, 16:34 
Offline
User avatar

Joined: September 16th, 2015, 9:06
Posts: 353
Location: Poland
Some Palmers just don't unlock properly with PC3000. But using unlocked PCB works good with those. I had one like this, made in 2017. The same problem. Also 01.26N

_________________
odzyskiwanie danych


Top
 Profile  
 
 Post subject: Re: Palmer ROM version 1.26N unlock?
PostPosted: July 8th, 2026, 2:56 
Offline

Joined: December 5th, 2011, 5:38
Posts: 1743
Location: Verona, Italy
You can try the MRT unlock
Attachment:
MRT Unlocked palmer.rar [410.78 KiB]
Downloaded 5 times

_________________
My firmware database:
https://mega.nz/folder/O01DkBRI


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 5 posts ] 

All times are UTC - 5 hours [ DST ]


Who is online

Users browsing this forum: No registered users and 67 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group