Barracuda 7200.10 Selfscan

To prepare selfscan, i need to save firmware first, because i have to send a cert file to the drive?
Does your ReadSA script work on my hdd too or just on alpine?

Here are some outputs from the commands:

Power cycle

Code:: Reset 4096k x 32 DRAM GALAXY - 1_Disk S-6D 09-22-06_15:48 HM SFI ! (P)SATA Reset (H)SATA Reset

^U

Code:: T>AT Stuff 0000: 0c5a 3fff c837 0010 0000 0000 003f 0000 0008: 0000 0000 2020 2020 2020 2020 2020 2020 0010: 3951 4631 4758 4d56 0000 8000 0004 332e 0018: 4141 4420 2020 5354 3333 3230 3632 3041 0020: 5320 2020 2020 2020 2020 2020 2020 2020 0028: 2020 2020 2020 2020 2020 2020 2020 8010 0030: 0000 2f00 4000 0200 0200 0007 3fff 0010 0038: 003f 0000 0000 0010 ffff 0fff 0000 0007 0040: 0003 0078 0078 00f0 0078 0000 0000 0000 0048: 0000 0000 0000 001f 0506 0000 0048 0040 0050: 00fe 0000 346b 7d01 4023 0061 3c00 4003 0058: 007f 0000 0000 fefe fffe 0000 fe00 0000 0060: 0000 0000 0000 0000 6a59 1edb 0000 0000 0068: 0000 0000 0000 0102 0000 0000 0000 0000 0070: 0004 0000 0000 0000 0000 0040 143e 0000 0078: 0000 0000 0140 0000 0440 0400 0800 0180 0080: 0001 eab0 2542 eab0 2542 2020 0002 02b6 0088: 8002 008a 3c06 3c0a 0000 07c6 0100 0800 0090: 1314 3000 0002 0080 0000 0000 00a2 0202 0098: 0000 0404 0000 0000 0000 0000 1200 000b 00a0: 000f 0006 0003 0000 0032 0014 0033 0024 00a8: 000f 001e 0032 0000 0013 0061 0032 0014 00b0: 0032 0000 003a 0000 0022 002d 0022 0000 00b8: 001a 0000 0012 0000 0010 0000 003e 0000 00c0: 0000 0000 0032 0000 0000 0000 0000 0000 00c8: 0000 0000 0000 0000 0000 0000 0000 0000 00d0: 0000 0000 0000 0000 0000 0000 0000 0000 00d8: 0000 0000 0000 0000 0001 0000 0000 0000 00e0: 0000 0000 0002 0000 0000 0000 0000 1200 00e8: 0000 0000 0000 ffff 00bd 0000 0000 0096 00f0: 0000 0000 0000 0000 0000 0000 0000 0000 00f8: 0000 0000 0000 1905 0203 0000 0000 0000 Configured-1 Part #: 100452451

^L

Code:: T>GALAXY2D - 2_Disk 3.AAD 11-03-06_16:41 AAE,GX_2D_4H_S,3A Built for GALAXY2D,PITKIN,Redback,TI1810 PreAmp,Agere7531 PreAmp,McKinleyDT,2Disk,220 Servos,7200RPM,8Pole,133MHz,RwFeat=0002,VBAR

^A

Code:: T>Eng Rev = .0GB Compat/Hardware = .6D1 GALAXY2D - 2_Disk 3.AAD 11-03-06_16:41 AAE,GX_2D_4H_S,3A CERT Rev = .0B9 NONE Mask Rom Rev = S-6D Orig Code = AAE3A0 TONKA2_GX_3A0.0GB.0B9

.

Code:: T>Pgm=00 Trk=0E755(0F935:54[10935]).2(2).000(000) Zn=4 Err=00 ErCt=0000 Hlth=0048 CHlth=0000 Ready LBA=13FE2813

;

Code:: T>Age=50 Type=18 MxCyl=205F3 MxHd=3 MxSct=55F BSz=016M TCode=03050405 ThermFlts=0000

%

Code:: T> :5000004818000003 AX`9QF1GXMV' "000000000000"160FC-1627B SRAM Ovly = Diag

?

Code:: BT:0000 PC:0056 AP:0060 RL:0298 AL:029B SL:02B3 MW:059C AT:0640 TB:0C48:0020 SO:0C68:0039 FS:0CA2:0038 RD:0640:0010 WR:0650:0010 FM:0660:0018 AD:0660:001C BA:0678:0003 ST:067B:0001 AS:067C:007F DP:06FB:02A6 AC:06FB:02A6 SC:09A1:02A7 CT:7B60 uP:7FC0 MZ:7FC0 logbps :0200 codebps:0200

k

Code:: T>k Head Mask = FF Map 00 to 00 00 Map 01 to 01 01 Map 02 to 02 02 Map 03 to 03 03

y

Code:: T>y Command Inactive - No VALID Cert Code Detected T>((VALID Cert Disk Code Detected - Revision # .0B9 T>y PhysCyl GrayCyl 1st Sys Cyl 000160FC 00016FBD 1st 0 Offset Cyl 00016106 00016FC7 1st App Code Cyl 00016112 00016FD3 2nd App Code Cyl 00016114 00016FD5 2nd 0 Offset Cyl 00016120 00016FE1 3rd App Code Cyl 0001612C 00016FED 4th App Code Cyl 0001612E 00016FEF 1st Adaptive Cyl 00016130 00016FF1 1st UsrDfect Cyl 00016136 00016FF7 1st Alt Pool Cyl 0001614E 0001700F 1st CertCode Cyl 0001616C 0001702D 1st IntfCode Cyl 00016170 00017031 1st Intf Sys Cyl 00016174 00017035 1st Cert Log Cyl 000161AE 0001706F 1st Decay Cyl 00016260 00017121 1st SPLASH Cyl 0001627A 0001713B Last System Cyl 0001627B 0001713C Copy PhysCyl StartSec length Name 0000 0016106 0000 0001 BootAdaptives 0001 0016106 00D5 0001 BootAdaptives 0002 0016106 01AA 0001 BootAdaptives 0003 0016120 0000 0001 BootAdaptives 0004 0016120 00D5 0001 BootAdaptives 0005 0016120 01AA 0001 BootAdaptives 0000 0016106 0001 0003 RsvTrackDefLst 0001 0016106 00D6 0003 RsvTrackDefLst 0002 0016106 01AB 0003 RsvTrackDefLst 0003 0016120 0001 0003 RsvTrackDefLst 0004 0016120 00D6 0003 RsvTrackDefLst 0005 0016120 01AB 0003 RsvTrackDefLst 0000 0016112 0000 0238 AppCode 0001 0016114 001E 0238 AppCode 0002 001612C 0000 0238 AppCode 0003 001612E 001E 0238 AppCode 0000 0016130 0000 001C DriveAdaps 0001 0016132 0028 001C DriveAdaps 0002 0016134 0050 001C DriveAdaps 0000 0016130 001C 0010 MediaZonTbl 0001 0016132 0044 0010 MediaZonTbl 0002 0016134 006C 0010 MediaZonTbl 0000 0016130 002C 0007 ACFCTbl 0001 0016132 0054 0007 ACFCTbl 0002 0016134 007C 0007 ACFCTbl 0000 0016130 0033 0007 BackUpACFCTbl 0001 0016132 005B 0007 BackUpACFCTbl 0002 0016134 0083 0007 BackUpACFCTbl 0000 0016130 003A 0018 AltLst 0001 0016132 0062 0018 AltLst 0002 0016134 008A 0018 AltLst 0000 0016130 0052 00A4 DosTbl 0001 0016132 007A 00A4 DosTbl 0002 0016134 00A2 00A4 DosTbl 0000 0016136 0000 027F UsrSlipKBALst 0001 001613A 0000 027F UsrSlipKBALst 0002 001613E 0000 027F UsrSlipKBALst 0000 0016138 0000 006A UsrSlipKBALst2 0001 001613C 0000 006A UsrSlipKBALst2 0002 0016140 0000 006A UsrSlipKBALst2 0000 0016142 0000 027F UsrSlipDftLst 0001 0016146 0000 027F UsrSlipDftLst 0002 001614A 0000 027F UsrSlipDftLst 0000 0016144 0000 006A UsrSlipDftLst2 0001 0016148 0000 006A UsrSlipDftLst2 0002 001614C 0000 006A UsrSlipDftLst2

x

Code:: 2>x Head 00 Zone 00: 00018 - 0289D 1496 (05D8) 940.645 Zone 01: 0289E - 05441 1466 (05BA) 921.774 Zone 02: 05442 - 0782F 1430 (0596) 900.000 Zone 03: 07830 - 0A32B 1375 (055F) 866.820 Zone 04: 0A32C - 0D09D 1320 (0528) 827.419 Zone 05: 0D09E - 0EDFB 1265 (04F1) 799.999 Zone 06: 0EDFC - 1106F 1210 (04BA) 764.516 Zone 07: 11070 - 12DCD 1155 (0483) 732.257 Zone 08: 12DCE - 15095 1100 (044C) 690.967 Zone 09: 15096 - 17165 1026 (0402) 651.612 Zone 0A: 17166 - 18E99 962 (03C2) 614.516 Zone 0B: 18E9A - 1AA53 904 (0388) 577.016 Zone 0C: 1AA54 - 1C493 836 (0344) 534.677 Zone 0D: 1C494 - 1D8EB 757 (02F5) 488.269 Head 01 Zone 00: 00018 - 029C7 1562 (061A) 982.258 Zone 01: 029C8 - 05B5F 1540 (0604) 962.211 Zone 02: 05B60 - 08AFD 1485 (05CD) 933.870 Zone 03: 08AFE - 0B845 1430 (0596) 900.000 Zone 04: 0B846 - 0E0B3 1375 (055F) 866.820 Zone 05: 0E0B4 - 10C2F 1320 (0528) 827.419 Zone 06: 10C30 - 133B7 1246 (04DE) 788.017 Zone 07: 133B8 - 15B9B 1173 (0495) 743.225 Zone 08: 15B9C - 177A3 1122 (0462) 712.902 Zone 09: 177A4 - 19B93 1056 (0420) 671.370 Zone 0A: 19B94 - 1BCFF 990 (03DE) 627.822 Zone 0B: 1BD00 - 1D6B1 935 (03A7) 596.480 Zone 0C: 1D6B2 - 1F0BF 880 (0370) 555.241 Zone 0D: 1F0C0 - 205F3 792 (0318) 508.064 Head 02 Zone 00: 00018 - 034D3 1518 (05EE) 958.064 Zone 01: 034D4 - 069E9 1485 (05CD) 933.870 Zone 02: 069EA - 09D10 1430 (0596) 900.000 Zone 03: 09D11 - 0C6E6 1375 (055F) 866.820 Zone 04: 0C6E7 - 0F4C7 1320 (0528) 827.419 Zone 05: 0F4C8 - 11141 1265 (04F1) 799.999 Zone 06: 11142 - 1340F 1210 (04BA) 764.516 Zone 07: 13410 - 150B6 1155 (0483) 732.257 Zone 08: 150B7 - 175FA 1100 (044C) 690.967 Zone 09: 175FB - 18DB5 1045 (0415) 663.594 Zone 0A: 18DB6 - 1AB3D 990 (03DE) 627.822 Zone 0B: 1AB3E - 1C979 916 (0394) 588.562 Zone 0C: 1C97A - 1E512 852 (0354) 545.806 Zone 0D: 1E513 - 1FAB1 770 (0302) 493.548 Head 03 Zone 00: 00018 - 0270F 1562 (061A) 982.258 Zone 01: 02710 - 0556B 1540 (0604) 962.211 Zone 02: 0556C - 081EE 1485 (05CD) 933.870 Zone 03: 081EF - 0AC42 1430 (0596) 900.000 Zone 04: 0AC43 - 0D20D 1375 (055F) 866.820 Zone 05: 0D20E - 0FAB3 1320 (0528) 827.419 Zone 06: 0FAB4 - 11FA7 1246 (04DE) 788.017 Zone 07: 11FA8 - 144F1 1173 (0495) 743.225 Zone 08: 144F2 - 15F25 1122 (0462) 712.902 Zone 09: 15F26 - 180BD 1056 (0420) 671.370 Zone 0A: 180BE - 19FFB 990 (03DE) 627.822 Zone 0B: 19FFC - 1B800 935 (03A7) 596.480 Zone 0C: 1B801 - 1D05B 880 (0370) 555.241 Zone 0D: 1D05C - 1E42D 792 (0318) 508.064 Reserve: 160FC - 1627B 640 (0280) 489.81 Total KBAs = 25779198

V4

Code:: T>V4 Alt Defect List Num Entries = 0043 Checksum = 8FCA Hd 0 Offset Hd 1 Offset Hd 2 Offset Hd 3 Offset 007FD.1.204 003C Alt 007FE.1.204 0040 Alt 007FF.1.204 0041 Alt 00800.1.204 003D Alt 089B7.3.2DE 0000 Alt 089B7.3.2DF 0001 Alt 089B7.3.2E0 0002 Alt 089B7.3.2E1 0003 Alt 089B7.3.2E2 0004 Alt 089B7.3.2E3 0005 Alt 089B7.3.2E4 0006 Alt 089B7.3.2E5 0007 Alt 089B7.3.2E6 0008 Alt 089B7.3.2E7 0009 Alt 089B7.3.2E8 000A Alt 089B7.3.2E9 000B Alt 089B7.3.2EA 000C Alt 089B7.3.2EB 000D Alt 089B7.3.2EC 000E Alt 089B7.3.2ED 000F Alt 089B7.3.2EE 0010 Alt 089B7.3.2EF 0011 Alt 089B7.3.2F0 0012 Alt 089B7.3.2F1 0013 Alt 089B8.3.2DE 0014 Alt 089B8.3.2DF 0015 Alt 089B8.3.2E0 0016 Alt 089B8.3.2E1 0017 Alt 089B8.3.2E2 0018 Alt 089B8.3.2E3 0019 Alt 089B8.3.2E4 001A Alt 089B8.3.2E5 001B Alt 089B8.3.2E6 001C Alt 089B8.3.2E7 001D Alt 089B8.3.2E8 001E Alt 089B8.3.2E9 001F Alt 089B8.3.2EA 0020 Alt 089B8.3.2EB 0021 Alt 089B8.3.2EC 0022 Alt 089B8.3.2ED 0023 Alt 089B8.3.2EE 0024 Alt 089B8.3.2EF 0025 Alt 089B8.3.2F0 0026 Alt 089B8.3.2F1 0027 Alt 089B9.3.2DE 0028 Alt 089B9.3.2DF 0029 Alt 089B9.3.2E0 002A Alt 089B9.3.2E1 002B Alt 089B9.3.2E2 002C Alt 089B9.3.2E3 002D Alt 089B9.3.2E4 002E Alt 089B9.3.2E5 002F Alt 089B9.3.2E6 0030 Alt 089B9.3.2E7 0031 Alt 089B9.3.2E8 0032 Alt 089B9.3.2E9 0033 Alt 089B9.3.2EA 0034 Alt 089B9.3.2EB 0035 Alt 089B9.3.2EC 0036 Alt 089B9.3.2ED 0037 Alt 089B9.3.2EE 0038 Alt 089B9.3.2EF 0039 Alt 089B9.3.2F0 003A Alt 089B9.3.2F1 003B Alt 097C0.1.158 8042 Bbm 12A0F.2.460 003E Alt 12A19.2.460 003F Alt

I see your drive is in quite good condition. very moderate number in G-list, health is deteriorated, but again not critical value 48 - 1001000 means bit 6 and 3 is set which means:
bit 6: (not disclosed) for internal use
bit 3: R/W notification
So not really errors. What SMART is telling you? Why do you want to recertify it? I think you should try N4, it is called selfscan-lite. It will certify user area, it will destroy all data, but you don't need backup and restore firmware.

But if you want to continue with N2, read on carefully, I don't have experience with this drive, all I can tell you - Galaxy - she is a bitch, you must be smart, as if you are not, you can turn Galaxy into a brick.

arztt wrote:To prepare selfscan, i need to save firmware first, because i have to send a cert file to the drive?
Does your ReadSA script work on my hdd too or just on alpine?

Yes, saving firmware is the one things and being able to restore it is other things. On this thread http://forum.hddguru.com/seagate-barracude-7200-8gb-st380011a-died-t23567.html you can find link to ST-Mem_free, I used to backup and restore firmware. The same mechanism is used to restore firmware. However:

Read carefully: Galaxy selfscan destroys APP code. This means that if you are lucky and immediately after selfscan reload APP code track using ST-Mem_free script, it is fine. But if if something goes wrong with selfscan or for some reason you cycle power on device, you will be not able to restore system tracks using the same utility.
Next time you power on device, you will end up on level F (called factory or FAIL). You must have plan to recover from such situation. I guess you need to find ST-Mem full version to upload code using SDLD protocol.

So unless you have backup plan, I don't think it is a good idea to continue with N2.

Yes very similiar scripts, just parameters will change, also for Alpine. Each drive has different Base track number and scripts have to be modified for each individual device

Thank you for your answer!

Why do you want to recertify it?

because it has the same problem as my 2 TB drive (which is now fully functional!). Too many bad sectors for the G-List, which I already cleared. The entries now come from a partial low level format, which i quitted after 10 minutes. If I do full llf, the G-List will be overfilled again and drive freezes.

I think you should try N4, it is called selfscan-lite.

Good one, I'll give it a try!

1. Reset SMART: 1>N1 (or N1,,22)
2. Cycle the power.
3. Reset health: T>H,,22
4. Start selfscan: N4,,22 (assuming it works on these drives)

Forgotten, If everything goes right, it will finish on test 99. Don't power off!
It would lose configuration still in buffers. Drive is just pausing and waiting for your input. Just thinking... maybe it is a time to fill platters with APP code (in case of N2)....
In any case, don't cycle power, press ^T tests will continue.

Ok ok, thank you.

Will try it this evening or tomorrow!

Just read that N10,,22 is more safe for Galaxy. If you didn't start N4 yet, try N10. If you did, don't interrupt.

I did N4 before you wrote the N10 command.

It found massive errors on the drive

Code:: . . . **********Loading Theta and Sorting by Theta & Cylinder for Head 0********** Loading Defect Groups among 1364 Defects on Head 0 1364 Defects pad & filled - Post Processing 24395 defects Buzz HM SFI ! *********Building Active Log from User Slip list for Head 1********** **********Loading Theta and Sorting by Theta & Cylinder for Head 1********** Loading Defect Groups among 2211 Defects on Head 1 Buzz HM SFI . . .

On one test the drive just stucked for 8 hours and there were no messages in terminal, but I just let it do.
Finally after another 12 hours it finished.

Code:: . . . Log 97 - Health 0000 - HlthDtl 0000 - Time = 00:08:41 Log Type = 01 Log 48 - Health 3000 - HlthDtl 0003 - Time = 01:22:40 Log Type = 01 Log 49 - Health 3000 - HlthDtl 0003 - Time = 01:17:43 Log Type = 01 Log 4B - Health 0000 - HlthDtl 0000 - Time = 00:17:49 Log Type = 01 Log 4D - Health 0000 - HlthDtl 0000 - Time = 00:04:50 Log Type = 01 Log 8B - Health 0000 - HlthDtl 0000 - Time = 00:00:08 Log Type = 01 Log E1 - Health 0000 - HlthDtl 0000 - Time = 00:04:03 Log Type = 01 Log 35 - Health 0000 - HlthDtl 0000 - Time = 00:04:18 Log Type = 01 Log 6F - Health 0000 - HlthDtl 0000 - Time = 00:00:13 Log Type = 01 Total Cert Time = 46:04:43 ASCII logging off Power Cycling End Test 4E

It needed 46 hours for the selfscan.
I set age back to 50 and now it's 100% repaired. No defects anymore and no delays. Thats incredible!
Ty again!

Still I wouldn't trust this drive.

Code:: Log 48 - Health 3000 - HlthDtl 0003 - Time = 01:22:40 Log Type = 01 Log 49 - Health 3000 - HlthDtl 0003 - Time = 01:17:43 Log Type = 01

Health 3000 means 13 and 12 bits set
bit 13: - Serious R/W error
bit 12: - Error rate Health
It looks not good. I don't know what is HlthDtl and how to interpret bit values.
Besides selftest didn't complete, as you wrote you had to reset age. If everything goes right, it finishes on age 50.
You can repeat tests to get more confidence in the drive.

Here's the full log from last test.

Code:: Begin Test 4E ASCII logging on Not Power Cycling ASCII logging off ASCII logging on Log 02 - Health 0018 - HlthDtl 000F - Time = 02:24:36 Log Type = 01 Log 04 - Health 0000 - HlthDtl 0000 - Time = 00:51:58 Log Type = 01 Log 83 - Health 0000 - HlthDtl 0000 - Time = 00:08:13 Log Type = 01 Log 84 - Health 0000 - HlthDtl 0000 - Time = 00:00:54 Log Type = 01 Log 03 - Health 0000 - HlthDtl 0000 - Time = 00:33:06 Log Type = 01 Log 8A - Health 0000 - HlthDtl 0000 - Time = 00:07:32 Log Type = 01 Log 05 - Health 0000 - HlthDtl 0000 - Time = 00:00:13 Log Type = 01 Log 06 - Health 0000 - HlthDtl 0000 - Time = 00:00:03 Log Type = 01 Log 07 - Health 0000 - HlthDtl 0000 - Time = 00:00:34 Log Type = 01 Log 90 - Health 0000 - HlthDtl 0000 - Time = 00:19:50 Log Type = 01 Log 93 - Health 0000 - HlthDtl 0000 - Time = 00:20:57 Log Type = 01 Log 98 - Health 0000 - HlthDtl 0000 - Time = 00:23:35 Log Type = 01 Log 9C - Health 0008 - HlthDtl 0002 - Time = 00:14:54 Log Type = 01 Log AA - Health 0000 - HlthDtl 0000 - Time = 00:25:29 Log Type = 01 Log 81 - Health 0000 - HlthDtl 0000 - Time = 00:57:21 Log Type = 01 Log 09 - Health 0008 - HlthDtl 0002 - Time = 01:30:48 Log Type = 01 Log 74 - Health 0000 - HlthDtl 0000 - Time = 00:34:15 Log Type = 01 Log F4 - Health 0000 - HlthDtl 0000 - Time = 00:02:33 Log Type = 01 Log 0F - Health 0000 - HlthDtl 0000 - Time = 00:00:02 Log Type = 01 Log 82 - Health 0000 - HlthDtl 0000 - Time = 00:02:36 Log Type = 01 Log 94 - Health 0000 - HlthDtl 0000 - Time = 00:01:10 Log Type = 01 Log 99 - Health 0000 - HlthDtl 0000 - Time = 00:00:01 Log Type = 01 Log 10 - Health 0000 - HlthDtl 0000 - Time = 00:18:54 Log Type = 01 Log 11 - Health 0000 - HlthDtl 0000 - Time = 00:16:23 Log Type = 01 Log 12 - Health 0000 - HlthDtl 0000 - Time = 00:17:15 Log Type = 01 Log 13 - Health 0000 - HlthDtl 0000 - Time = 00:17:35 Log Type = 01 Log 14 - Health 0000 - HlthDtl 0000 - Time = 00:13:45 Log Type = 01 Log 15 - Health 0000 - HlthDtl 0000 - Time = 00:22:19 Log Type = 01 Log 16 - Health 0000 - HlthDtl 0000 - Time = 00:17:45 Log Type = 01 Log 17 - Health 0000 - HlthDtl 0000 - Time = 00:17:42 Log Type = 01 Log 18 - Health 0000 - HlthDtl 0000 - Time = 00:21:35 Log Type = 01 Log 19 - Health 0000 - HlthDtl 0000 - Time = 00:16:32 Log Type = 01 Log 1A - Health 0000 - HlthDtl 0000 - Time = 00:20:20 Log Type = 01 Log 1B - Health 0000 - HlthDtl 0000 - Time = 00:17:53 Log Type = 01 Log 1C - Health 0000 - HlthDtl 0000 - Time = 00:17:34 Log Type = 01 Log 1D - Health 0008 - HlthDtl 0002 - Time = 00:13:21 Log Type = 01 Log 1E - Health 0000 - HlthDtl 0000 - Time = 00:15:03 Log Type = 01 Log 2A - Health 0008 - HlthDtl 0001 - Time = 00:24:53 Log Type = 01 Log DA - Health 0000 - HlthDtl 0000 - Time = 00:00:08 Log Type = 01 Log DC - Health 0000 - HlthDtl 0000 - Time = 00:00:07 Log Type = 01 Log D6 - Health 0000 - HlthDtl 0000 - Time = 00:00:07 Log Type = 01 Log D7 - Health 0000 - HlthDtl 0000 - Time = 00:00:12 Log Type = 01 Log D8 - Health 0000 - HlthDtl 0000 - Time = 00:00:12 Log Type = 01 Log D9 - Health 0000 - HlthDtl 0000 - Time = 00:00:11 Log Type = 01 Log DB - Health 0000 - HlthDtl 0000 - Time = 00:00:05 Log Type = 01 Log DD - Health 0000 - HlthDtl 0000 - Time = 00:00:07 Log Type = 01 Log 0B - Health 0000 - HlthDtl 0000 - Time = 00:00:28 Log Type = 01 Log 7C - Health 0000 - HlthDtl 0000 - Time = 00:00:08 Log Type = 01 Log 78 - Health 0000 - HlthDtl 0000 - Time = 00:00:06 Log Type = 01 Log 58 - Health 0000 - HlthDtl 0000 - Time = 00:16:36 Log Type = 01 Log 86 - Health 0000 - HlthDtl 0000 - Time = 00:39:51 Log Type = 01 Log 8F - Health 0000 - HlthDtl 0000 - Time = 00:09:46 Log Type = 01 Log 31 - Health 0000 - HlthDtl 0000 - Time = 04:34:40 Log Type = 02 Log AB - Health 0000 - HlthDtl 0000 - Time = 00:00:03 Log Type = 01 Log 32 - Health 0000 - HlthDtl 0000 - Time = 03:25:26 Log Type = 02 Log AB - Health 0000 - HlthDtl 0000 - Time = 00:00:03 Log Type = 01 Log 33 - Health 0000 - HlthDtl 0000 - Time = 03:09:32 Log Type = 02 Log AB - Health 0000 - HlthDtl 0000 - Time = 00:00:03 Log Type = 01 Log 34 - Health 0000 - HlthDtl 0000 - Time = 03:24:02 Log Type = 02 Log AB - Health 0000 - HlthDtl 0000 - Time = 00:00:03 Log Type = 01 Log 36 - Health 0000 - HlthDtl 0000 - Time = 00:23:42 Log Type = 02 Log A8 - Health 0000 - HlthDtl 0000 - Time = 00:05:20 Log Type = 02 Log 37 - Health 0000 - HlthDtl 0000 - Time = 00:00:37 Log Type = 02 Log 26 - Health 0000 - HlthDtl 0000 - Time = 00:00:12 Log Type = 01 Log 3A - Health 0000 - HlthDtl 0000 - Time = 03:54:31 Log Type = 02 Log 3B - Health 8000 - HlthDtl 0000 - Time = 03:59:55 Log Type = 02 Log 3C - Health 2020 - HlthDtl 0000 - Time = 01:50:56 Log Type = 02 Log 3D - Health 0000 - HlthDtl 0000 - Time = 00:00:00 Log Type = 02 Log 3E - Health 0000 - HlthDtl 0000 - Time = 00:00:00 Log Type = 02 Log A9 - Health 0000 - HlthDtl 0000 - Time = 00:00:08 Log Type = 01 Log 3F - Health 0000 - HlthDtl 0000 - Time = 00:01:01 Log Type = 01 Log 20 - Health 0000 - HlthDtl 0000 - Time = 00:06:37 Log Type = 01 Log 74 - Health 0000 - HlthDtl 0000 - Time = 00:34:15 Log Type = 01 Log 87 - Health 0000 - HlthDtl 0000 - Time = 00:45:15 Log Type = 01 Log 88 - Health 0000 - HlthDtl 0000 - Time = 00:00:06 Log Type = 01 Log 41 - Health 0000 - HlthDtl 0000 - Time = 00:32:54 Log Type = 01 Log 44 - Health 0000 - HlthDtl 0000 - Time = 00:57:24 Log Type = 01 Log 97 - Health 0000 - HlthDtl 0000 - Time = 00:08:41 Log Type = 01 Log 48 - Health 3000 - HlthDtl 0003 - Time = 01:22:40 Log Type = 01 Log 49 - Health 3000 - HlthDtl 0003 - Time = 01:17:43 Log Type = 01 Log 4B - Health 0000 - HlthDtl 0000 - Time = 00:17:49 Log Type = 01 Log 4D - Health 0000 - HlthDtl 0000 - Time = 00:04:50 Log Type = 01 Log 8B - Health 0000 - HlthDtl 0000 - Time = 00:00:08 Log Type = 01 Log E1 - Health 0000 - HlthDtl 0000 - Time = 00:04:03 Log Type = 01 Log 35 - Health 0000 - HlthDtl 0000 - Time = 00:04:18 Log Type = 01 Log 6F - Health 0000 - HlthDtl 0000 - Time = 00:00:13 Log Type = 01 Total Cert Time = 46:04:43 ASCII logging off

I think I first stress test the drive some days and look at SMART. It looks quite good now, good performance and no errors.

Barracuda 7200.10 Selfscan

Barracuda 7200.10 Selfscan

Re: Barracuda 7200.10 Selfscan

Re: Barracuda 7200.10 Selfscan

Re: Barracuda 7200.10 Selfscan

Re: Barracuda 7200.10 Selfscan

Re: Barracuda 7200.10 Selfscan

Re: Barracuda 7200.10 Selfscan

Re: Barracuda 7200.10 Selfscan

Re: Barracuda 7200.10 Selfscan

Re: Barracuda 7200.10 Selfscan