MultiDrive – free backup, clone & wipe disk utility from Atola Technology

Main » Forums home » Conventional hard drives

All times are UTC - 5 hours [ DST ]



Post new topic Reply to topic  Page 1 of 1
  [ 8 posts ] 
  Previous topic | Next topic 
Author Message
raven4d
 Post subject: t9500424as BSY
PostPosted: March 23rd, 2013, 5:33 
Offline

Joined: August 16th, 2012, 4:57
Posts: 324
Good morning ;

i have a st9500424as
reporting BSY

terminal log is


EarlySpinup Enabled
Rst 0x10M
ExecuteSpinRequest

LED:00000067 FAddr:00380342
LED:00000067 FAddr:00380342
LED:00000067 FAddr:00380342

the drive was NOT dropped and was being used normally when hanged and not detected anymore .
and it's not clicking

thank you for your ideas
Top
 Profile  
 
jignesh
 Post subject: Re: t9500424as BSY
PostPosted: March 23rd, 2013, 5:49 
Offline

Joined: March 21st, 2013, 14:45
Posts: 121
Location: India
raven4d wrote:
Good morning ;

i have a st9500424as
reporting BSY

terminal log is


EarlySpinup Enabled
Rst 0x10M
ExecuteSpinRequest

LED:00000067 FAddr:00380342
LED:00000067 FAddr:00380342
LED:00000067 FAddr:00380342

the drive was NOT dropped and was being used normally when hanged and not detected anymore .
and it's not clicking

thank you for your ideas



Hi Dear Friend Raven4d

Firmware Info Plz
Top
 Profile  
 
raven4d
 Post subject: Re: t9500424as BSY
PostPosted: March 23rd, 2013, 6:03 
Offline

Joined: August 16th, 2012, 4:57
Posts: 324
jignesh wrote:
raven4d wrote:
Good morning ;

i have a st9500424as
reporting BSY

terminal log is


EarlySpinup Enabled
Rst 0x10M
ExecuteSpinRequest

LED:00000067 FAddr:00380342
LED:00000067 FAddr:00380342
LED:00000067 FAddr:00380342

the drive was NOT dropped and was being used normally when hanged and not detected anymore .
and it's not clicking

thank you for your ideas



Hi Dear Friend Raven4d

Firmware Info Plz



thank you for your reply

FW:0001BSM1
Top
 Profile  
 
jignesh
 Post subject: Re: t9500424as BSY
PostPosted: March 23rd, 2013, 11:58 
Offline

Joined: March 21st, 2013, 14:45
Posts: 121
Location: India
raven4d wrote:
jignesh wrote:
raven4d wrote:
Good morning ;

i have a st9500424as
reporting BSY

terminal log is


EarlySpinup Enabled
Rst 0x10M
ExecuteSpinRequest

LED:00000067 FAddr:00380342
LED:00000067 FAddr:00380342
LED:00000067 FAddr:00380342

the drive was NOT dropped and was being used normally when hanged and not detected anymore .
and it's not clicking

thank you for your ideas



Hi Dear Friend Raven4d

Firmware Info Plz



thank you for your reply

FW:0001BSM1


Dear friend raven4d
Wich Platform U Have Like PC-3000 UDMA Or SalvationData Or Other ?
Tell Me So I Will Give You Some Tips And Advice And Ya Brother Post Your
PCB Pictur Front And Backside Both So I Will Check And Advice If U Have Any Good Platform.
Top
 Profile  
 
raven4d
 Post subject: Re: t9500424as BSY
PostPosted: March 23rd, 2013, 16:16 
Offline

Joined: August 16th, 2012, 4:57
Posts: 324
thank you for your idea ..


connecting only the pcb will give the same results !!!

Rst 0x10M
ExecuteSpinRequest

LED:00000067 FAddr:00380338
LED:00000067 FAddr:00380338
LED:00000067 FAddr:00380338


so , it's not bad heads i think , will try to find a similar drive if not a donor to test with .

thank you again
Top
 Profile  
 
raven4d
 Post subject: Re: t9500424as BSY
PostPosted: March 23rd, 2013, 17:15 
Offline

Joined: August 16th, 2012, 4:57
Posts: 324
Spildit wrote:
Do you have external eeprom programer ? Maybe you can dump the ROM on the PCB (if it have one) using an external programmer to check if it's ok or not ...




yes , it does has an external eeprom , will try to dump it's content tomorrow's morning ..

thank you
Top
 Profile  
 
ROb
 Post subject: Re: t9500424as BSY
PostPosted: March 10th, 2014, 6:00 
Offline

Joined: April 16th, 2008, 4:50
Posts: 264
Hello Similar problem to what "reven4d" has been facing

My Model is ST9500423AS Fw: 0003HPM1
Drive spins up initializes properly but remains BUSY
Tried to get terminal access with but could get it only for fraction of seconds then it gives LED CC Error
[quoteEarlySpinup Enabled
Rst 0x10M
ASCII Diag mode

F3 T>
LED:00000067 FAddr:00384F74
LED:00000067 FAddr:00384F74
LED:00000067 FAddr:00384F74
][/quote]

Only PCB attains ready state but no TERMINAL Access / Terminal lock.

Any suggestions ???
Top
 Profile  
 
ROb
 Post subject: Re: t9500424as BSY No TERMINAL Access
PostPosted: March 13th, 2014, 2:20 
Offline

Joined: April 16th, 2008, 4:50
Posts: 264
Hello Similar problem to what "reven4d" has been facing

My Model is ST9500423AS Fw: 0003HPM1
Drive spins up initializes properly but remains BUSY
Tried to get terminal access with but could get it only for fraction of seconds then it gives LED CC Error
[quoteEarlySpinup Enabled
Rst 0x10M
ASCII Diag mode

F3 T>
LED:00000067 FAddr:00384F74
LED:00000067 FAddr:00384F74
LED:00000067 FAddr:00384F74
][/quote]

Only PCB attains ready state but no TERMINAL Access / Terminal lock.

Any suggestions ???
Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  Page 1 of 1
  [ 8 posts ] 

Main » Forums home » Conventional hard drives

All times are UTC - 5 hours [ DST ]

Who is online

Users browsing this forum: No registered users and 38 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Switch to mobile style
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group