HELP - ST3500418AS Problem After Frimware Upgrade

[mo4sa]

My Hard Disk Is Seagate ST3500418AS Original Firmware CC38 And Me Upgraded To CC49

After Update the firmware My Hard Disk Is Detected On Device Manager And On Disk Management Not Happen And Not Show Hard Disk Or Drives On My Hard Disk ,

Me Connected Hard Disk On RS232 Controller And Show This Command :

Code:

Rst 0x10M
Servo Processor Is Reset.
RW: Disc Ctlr Initialization Completed.

ExecuteSpinRequest

No HOST FIS-ReadyStatusFlags 2002B001
ASCII Diag mode

F3 T>/2

F3 2>Z

HighPowerMode
Spin Down Complete
Elapsed Time 0.087 msecs
F3 2>U

HighPowerMode
ExecuteSpinRequest

Spin Up Complete
Elapsed Time 3.758 secs
F3 2>/1

F3 1>N1

Rst 0x10M
Servo Processor Is Reset.
RW: Disc Ctlr Initialization Completed.

ExecuteSpinRequest

No HOST FIS-ReadyStatusFlags 2002B001
ASCII Diag mode

F3 T>/2

F3 2>Z

HighPowerMode
Spin Down Complete
Elapsed Time 0.086 msecs
F3 2>U

HighPowerMode
ExecuteSpinRequest

Spin Up Complete
Elapsed Time 3.758 secs
F3 2>
ASCII Diag mode

F3 T>m0,2,2,0,0,0,0,22
Max Wr Retries = 00, Max Rd Retries = 00, Max ECC T-Level = 00, Max Certify Rewr
ite Retries = not supported

DiagError 0000500D
User Partition Format Failed - Elapsed Time 0 mins 00 secs
R/W Sense 00000002, R/W Error 843200A6, File Error 00000000
Blk Addr 000071030001, Blk Addr Type D0, Cyl FFFF0000, Hd 28

F3 T>
ASCII Diag mode

F3 T>V4

Reassigned Sectors List
Entries: 0000, Retrieved: 0000, Alts: 0000, Removed: 061B, Pending: 0000, GList:
0000, RList: 0000

Idx  LBA          PBA          LLLCHS of LBA PLPCHS of PBA SFI    Hours Msecs  S
tatus   BBM Mask

F3 T>V1
User Slip Defect List
                         log log   log     phys   phys
        LBA    span   cumm   cyl  hd  sctr zn   cyl   sctr     SFI      PBA
           0      0      0     0  0     0   0      0     0        4            0


Head 0: entries      1        slips        0
Head 1: entries      0        slips        0
  Total Entries      1  Total Slips        0

F3 T>m0,2,2,,,,,22,
Max Wr Retries = 00, Max Rd Retries = 00, Max ECC T-Level = 16, Max Certify Rewr
ite Retries = not supported

DiagError 0000500D
User Partition Format Failed - Elapsed Time 0 mins 00 secs
R/W Sense 00000002, R/W Error 843200A6, File Error 00000000
Blk Addr 000071030001, Blk Addr Type D0, Cyl 00000000, Hd 00

F3 T>

Please Help Me To Fix This Drive .

Thanks .

[mo4sa]

Hello

Friends will not anyone help me in solving this problem

Thanks

[shahij]

Why did u go for UPDATE?

Why did you execute translator regeneration? WHAT IS THE VALID REASON?

Go and replace your HDD.

[tutuyale]

Sorry but....YOU KILLED YOUR HARD DRIVE AND IS DEAD! OR ALMOST YOU GIVE THE ORIGINAL FIRMWARE, CONTACT TO SEAGATE AND REQUEST THE ORIGINAL FIRMWARE!!!

[HaQue]

Sorry but....YOU KILLED YOUR HARD DRIVE AND IS DEAD! OR ALMOST YOU GIVE THE ORIGINAL FIRMWARE, CONTACT TO SEAGATE AND REQUEST THE ORIGINAL FIRMWARE!!!

don't you have that magical firmware that fixes all Seagate drives anymore?

[tutuyale]

Sorry but....YOU KILLED YOUR HARD DRIVE AND IS DEAD! OR ALMOST YOU GIVE THE ORIGINAL FIRMWARE, CONTACT TO SEAGATE AND REQUEST THE ORIGINAL FIRMWARE!!!

don't you have that magical firmware that fixes all Seagate drives anymore?

YES, but if you see in the picture, the firmware is corrupted, the other solution is find other new or used PBC and install in the HDD, but you need sure the S/N AND FIRMWARE IS SAME OF THE ORIGINAL!!!