HTS541010A7E630 (NEWEST MODEL)

[saadraa]

HTS541010A7E630 spin up but cap=0 not det in mrt & cant read nvram or mlist problem is pcb for fix you must soldering the spindle motor ic & nvram chip just heating that chips for few sec its work for me & det by mrt as basic access whit full cap good luck

[HddDonorMarket]

HTS541010A7E630
Usıng MRT
Selected family:Tech-Key detection

Model:HGST HTS541010A7E630

Technology key : ....................................OK

Reading module list failed,try Copy1......
Read module list : ..................................Error

Read open module list : .............................Error

get the head number : ...............................04

Backuping NV-RAM...
Save Path :C:\UserDataFile\Hitachi-ARM\Tech-Key detection\HGST HTS541010A7E630-SE0OA4A0-S00001SSGTRHRF\Data\NV-RAM\
NV_RAM.nvr : ........................................OK
NV-RAM_0.nvr : ......................................OK
NV-RAM_1.nvr : ......................................OK
NV-RAM_2.nvr : ......................................OK
NV-RAM_3.nvr : ......................................OK
NV-RAM_4.nvr : ......................................OK
Backup NV-RAM : .....................................Complete

Reading ROM
Save path:C:\UserDataFile\Hitachi-ARM\Tech-Key detection\HGST HTS541010A7E630-SE0OA4A0-S00001SSGTRHRF\Data\ROM\
Save ROM : ..........................................Succeed



Drıve ID ok. but 0 capacity

Who knows what is the problem?

Attachments

HGST HTS541010A7E630-SE0OA4A0-S00001SSGTRHRF.rar

(136.44 KiB) Downloaded 595 times

[pepe]

Is the pcb native?
pepe

[pepe]

i recall i had pcb problems with these. Drive spun up but heads did not move or something like that.
pepe

[HddDonorMarket]

Is the pcb native?
pepe

Customer's hdd. But I guess native.
Sometimes at start making 1 click.
Drive working sound nice. Very quickly getting ready status.

If I could find donor, I would change head.

[pepe]

does it move heads at all? have you checekd SN in nvram and on label?

pepe

[HddDonorMarket]

does it move heads at all? have you checekd SN in nvram and on label?

pepe

both yes

[mhp666]

The tool gives those numbers nonsense because it is not recognizing NVRAM well. In addition, you must be careful with MRTLAB, since with some model if the head map is modified and is left as it was, the NVRAM is altered and may not start the disk again.

[rakeshor]

HTS541010A7E630
Usıng MRT
Selected family:Tech-Key detection

Model:HGST HTS541010A7E630

Technology key : ....................................OK

Reading module list failed,try Copy1......
Read module list : ..................................Error

Read open module list : .............................Error

get the head number : ...............................04

Backuping NV-RAM...
Save Path :C:\UserDataFile\Hitachi-ARM\Tech-Key detection\HGST HTS541010A7E630-SE0OA4A0-S00001SSGTRHRF\Data\NV-RAM\
NV_RAM.nvr : ........................................OK
NV-RAM_0.nvr : ......................................OK
NV-RAM_1.nvr : ......................................OK
NV-RAM_2.nvr : ......................................OK
NV-RAM_3.nvr : ......................................OK
NV-RAM_4.nvr : ......................................OK
Backup NV-RAM : .....................................Complete

Reading ROM
Save path:C:\UserDataFile\Hitachi-ARM\Tech-Key detection\HGST HTS541010A7E630-SE0OA4A0-S00001SSGTRHRF\Data\ROM\
Save ROM : ..........................................Succeed



Drıve ID ok. but 0 capacity

Who knows what is the problem?

[saltwater]

The problem is a ROM failure.

1. Make backup of NvRAM from patient drive.
2. Upload NvRAM from DONOR drive to PATIENT drive .The DONOR drive have to be the same fw-microcode.
3. Power reset the patient drive (the patient drive will not spin up, but sends DRDY state for a sec).
4. Upload original NvRAM to patient drive.
5. Power reset patient drive.

This worked for me.

Cheers!