After selfscan disappeared cert ST9250827AS

[toker]

Now I do not know how to revive it? Here is what you see:
^C
T>(INVALID Cert Disk Code - ROM Resident Revision Required: AAZ790
^A
T>Eng Rev = .164
Compat/Hardware = .4T9
CORSAIR - 1_Disk 3.AAA 11-03-08_14:04 AAA,CR_2D_4H_S,79
CERT Rev = .028
NONE
Mask Rom Rev = S-00
Orig Code = AAZ790 VENUS_CR_790.164.028
Idle-Modifiable Disabled


e c r = 0 1 0
F>j

ERR 40: App Code
T>/1
1>r
cmd 58, params 0033 0000 0000 0520 3760 0520 0000 0000 000A C401 0033

cmd 58, params 0033 0000 0000 0520 3760 0520 0000 0000 000A C401 0033
INVALID Cert Disk Code - ROM Resident Revision Required: AAZ790
Code - 70 Track FFFFF(0F2A5).0.1E9 Sns FFF Rty 027F.82.80FF Rtf 1800 LB
A 00003860
1>t
Command Inactive - No VALID Cert Code Detected

Save cer forgot....
Maybe someone has time to help me figure it out, information on the disk is not needed.

[toker]

I just started to understand, help, please!

[toker]

Thanks.

Buzz HM SFI
!
(P)Not Interface Age!
INVALID Cert Disk Code - ROM Resident Revision Required: AAZ790
Command Inactive - No VALID Cert Code Detected

^R
T>(INVALID Cert Disk Code - ROM Resident Revision Required: AAZ790

T>
";"
T>Age=60 Type=00 MxCyl=00000 MxHd=0 MxSct=000 BSz=008M TCode=00000000
"."
Pgm=00 Trk=FFFFF(0F2A5:00[1107D]).0(0).1E9(FFF) Zn=0 Err=00 ErCt=0000 Hlth=0000
CHlth=0000 Ready LBA=00001480
"%"
:6000000000000000 AX` ' "000000000000"0F23D-0F36A
SRAM Ovly = Diag

no command is executed without cert, tell me please what to do next?

[toker]

T>N50,,22
Wrong data format. Write Adaptives rejected
Code - FD Track FFFFF(0F2A5).0.1E9 Sns FFF Rty 027F.82.80FF Rtf 1800 LB
A 00000A40
T>
Does not work?

[toker]

Without AA. How to recover? Please!

[toker]

It was installed in an old laptop grandmother, there is absolutely no money. She will not be able to buy, will wait to be repaired for free or who will give the old. If you can help, I will perform all the actions that you tell me.

[toker]

It was very oxidized, I cleaned and launched SS, decided to remove soft bad I used before to do it with a neighbor, but I didn’t save the components, after a day I arrived there was already a mistake. How do I find components and revive it? There is a terminal, I read about the sdld, but I never used it.

[toker]

I read that you can pick up resources, fill in with the help of the sdld and run SS. All photos and passwords from the hard disk are stored in us flash. Save them is not necessary. Then i can install the system.

[toker]

We bought this cheaply from the hands, it worked very little. Prior to this, stood st9500325as momentus 5400.6 sharply climbed bad, the warranty is long over. I think one head failed there, I don’t know how to turn it off, can you even tell me?
Head 0: entries 53A slips 1004
Head 1: entries 428 slips CF7
Head 2: entries D4 slips 39D
Head 3: entries 71 slips 17D
Total Entries AA7 Total Slips 2215

Alt Pending Total Alted Total
Entries Entries Entries Alts Alts
Head 0 2
Head 1 0
Head 2 D
Head 3 0
Total 47F F 48E 27C 6FB
Total Alt Removals: 0
Checksum = 6688

Tell me what commands to check the head and turn off?

[toker]

We bought this cheaply from the hands, it worked very little. Prior to this, stood st9500325as momentus 5400.6 sharply climbed bad, the warranty is long over. I think one head failed there, I don’t know how to turn it off, can you even tell me?
Alt Pending Total Alted Total
Entries Entries Entries Alts Alts
Head 0 2
Head 1 0
Head 2 D
Head 3 0
Total 47F F 48E 27C 6FB
Total Alt Removals: 0
Tell me what commands to check the head and turn off?

[toker]

commands /2TFFF and /2T880 show nothing.
incomprehensible format? until the end of even 5 days does not reach, left at work.
Why does lba from 02B02DAC jump to 000312E4?

F3 T>m0,20,3,10,3,,,22
Max Wr Retries = 10, Max Rd Retries = 03, Max ECC T-Level = 14, Max Certify Rewr
ite Retries = 0A74

User Partition Format 0% complete, Zone 00, Pass 00, LBA 0044942E, ErrCode 000
00080, Elapsed Time 0 mins 30 secs
User Partition Format 0% complete, Zone 00, Pass 00, LBA 00896107, ErrCode 000
00080, Elapsed Time 1 mins 00 secs
User Partition Format 0% complete, Zone 00, Pass 00, LBA 00CE0B68, ErrCode 000
00080, Elapsed Time 1 mins 30 secs
User Partition Format 0% complete, Zone 00, Pass 00, LBA 0112FF63, ErrCode C40
90081, Elapsed Time 2 mins 00 secs
User Partition Format 1% complete, Zone 00, Pass 00, LBA 0157D8ED, ErrCode 000
00080, Elapsed Time 2 mins 30 secs
User Partition Format 1% complete, Zone 00, Pass 00, LBA 019C82B8, ErrCode 000
00080, Elapsed Time 3 mins 00 secs
User Partition Format 1% complete, Zone 00, Pass 00, LBA 01E1899A, ErrCode 000
00080, Elapsed Time 3 mins 30 secs
User Partition Format 1% complete, Zone 00, Pass 00, LBA 0226ABAF, ErrCode 000
00080, Elapsed Time 4 mins 00 secs
User Partition Format 2% complete, Zone 00, Pass 00, LBA 026B788C, ErrCode C40
90081, Elapsed Time 4 mins 30 secs
User Partition Format 2% complete, Zone 00, Pass 00, LBA 02B02DAC, ErrCode 000
00080, Elapsed Time 5 mins 00 secs
User Partition Format 2% complete, Zone 00, Pass 01, LBA 000312E4, ErrCode 431
User Partition Format 2% complete, Zone 00, Pass 01, LBA 000312E4, ErrCode 431
User Partition Format 2% complete, Zone 00, Pass 01, LBA 000313B6, ErrCode 431
10081, Elapsed Time 6 mins 00 secs
User Partition Format 2% complete, Zone 00, Pass 01, LBA 00031499, ErrCode 000
00080, Elapsed Time 6 mins 30 secs
User Partition Format 2% complete, Zone 00, Pass 01, LBA 0003156B, ErrCode 000
00080, Elapsed Time 7 mins 00 secs
User Partition Format 2% complete, Zone 00, Pass 01, LBA 0003163B, ErrCode 431
10081, Elapsed Time 7 mins 30 secs
User Partition Format 2% complete, Zone 00, Pass 01, LBA 00031705, ErrCode 431
10081, Elapsed Time 8 mins 00 secs
User Partition Format 2% complete, Zone 00, Pass 01, LBA 000317CC, ErrCode 431
10081, Elapsed Time 8 mins 30 secs
User Partition Format 2% complete, Zone 00, Pass 01, LBA 00031893, ErrCode 431
10081, Elapsed Time 9 mins 00 secs
User Partition Format 2% complete, Zone 00, Pass 01, LBA 00031946, ErrCode 431
10081, Elapsed Time 9 mins 30 secs
User Partition Format 2% complete, Zone 00, Pass 01, LBA 00031A11, ErrCode 431
10081, Elapsed Time 10 mins 00 secs
User Partition Format 2% complete, Zone 00, Pass 01, LBA 00031ADD, ErrCode 431
10081, Elapsed Time 10 mins 30 secs
User Partition Format 2% complete, Zone 00, Pass 01, LBA 00031BAB, ErrCode 000
00080, Elapsed Time 11 mins 00 secs
User Partition Format 2% complete, Zone 00, Pass 01, LBA 00031C7A, ErrCode 431
10081, Elapsed Time 11 mins 30 secs

[toker]

Tell me, in your experience, which manufacturer is better to buy, so that he worked for a long time?