MultiDrive – free backup, clone & wipe disk utility from Atola Technology

Main » Forums home » Conventional hard drives

All times are UTC - 5 hours [ DST ]



Post new topic Reply to topic  Page 1 of 1
  [ 12 posts ] 
  Previous topic | Next topic 
Author Message
smecca
 Post subject: DT01ACA AND DT01ABA CROSS COMP.
PostPosted: November 18th, 2024, 13:50 
Offline

Joined: March 21st, 2009, 14:53
Posts: 56
Location: Malta
Hi guys,
I've seen references toshiba sheets about these two series. About hardware, rotational speed are different (respectively 7200 rpm the first and 5940 / 5700 rpm).
I was wondering if their headsets are cross comptible, and I would like to try this on a couple of these hdd (aca300 aba300)

So just to share opinion and experience, this is my question:
Has allready someone of you tryied if C.C. is possible among their headsets?
Thank you in advance for advices and opinions
Top
 Profile  
 
fzabkar
 Post subject: Re: DT01ACA AND DT01ABA CROSS COMP.
PostPosted: November 18th, 2024, 15:04 
Offline
User avatar

Joined: September 8th, 2009, 18:21
Posts: 16960
Location: Australia
I've heard that people have been able to use 7200RPM WD heads in 5400RPM WD drives and vice versa. Whilst I have no experience in head swaps, I would think that a head that was designed to fly at a particular height in a 7200RPM drive would fly lower in a 5400RPM drive, and vice versa.

_________________
A backup a day keeps DR away.
Top
 Profile  
 
smecca
 Post subject: Re: DT01ACA AND DT01ABA CROSS COMP.
PostPosted: November 18th, 2024, 16:26 
Offline

Joined: March 21st, 2009, 14:53
Posts: 56
Location: Malta
fzabkar wrote:
I've heard that people have been able to use 7200RPM WD heads in 5400RPM WD drives and vice versa. Whilst I have no experience in head swaps, I would think that a head that was designed to fly at a particular height in a 7200RPM drive would fly lower in a 5400RPM drive, and vice versa.


Thank you for your answer.
I with examine carefully both headset and update this post
Top
 Profile  
 
pepe
 Post subject: Re: DT01ACA AND DT01ABA CROSS COMP.
PostPosted: November 19th, 2024, 20:20 
Offline

Joined: October 3rd, 2005, 0:40
Posts: 4753
Location: Hungary
fzabkar wrote:
I've heard that people have been able to use 7200RPM WD heads in 5400RPM WD drives and vice versa. Whilst I have no experience in head swaps, I would think that a head that was designed to fly at a particular height in a 7200RPM drive would fly lower in a 5400RPM drive, and vice versa.


the tangential velocity difference between ID and OD is far more than between 5400 and 7200. And a lot of heads are interchangeable and even more if you know how to trick the fw.

_________________
Adatmentés - Data recovery
Top
 Profile  
 
fzabkar
 Post subject: Re: DT01ACA AND DT01ABA CROSS COMP.
PostPosted: November 19th, 2024, 21:11 
Offline
User avatar

Joined: September 8th, 2009, 18:21
Posts: 16960
Location: Australia
A 5400RPM head will fly lower than a 7200RPM head at the same physical location, would it not? So, for a particular head, the lowest fly height at 5400 RPM will be lower than the lowest fly height at 7200 RPM.

_________________
A backup a day keeps DR away.
Top
 Profile  
 
smecca
 Post subject: Re: DT01ACA AND DT01ABA CROSS COMP.
PostPosted: December 12th, 2024, 7:28 
Offline

Joined: March 21st, 2009, 14:53
Posts: 56
Location: Malta
Hi everybody and in particular those little who wanted to take part to this topic.

Just to give an update to this case.
So...
yes! it worked.
98% of fs data recovered with oneshot head swap.
Cross comp verifyied
Thanks to all and best regards
Top
 Profile  
 
Amarbir[CDR-Labs]
 Post subject: Re: DT01ACA AND DT01ABA CROSS COMP.
PostPosted: December 17th, 2024, 3:00 
Offline
User avatar

Joined: August 15th, 2006, 3:01
Posts: 3522
Location: CDRLabs @ Chandigarh [ India ]
fzabkar wrote:
A 5400RPM head will fly lower than a 7200RPM head at the same physical location, would it not? So, for a particular head, the lowest fly height at 5400 RPM will be lower than the lowest fly height at 7200 RPM.


Frank ,
if heads are compatible then fw will adjust fly height wont it ? . in a 5400 rpm it will be different and in 7200 it will be different ,So FW will do this adjustment not the physical HSA ?

_________________
Regards
Amarbir S Dhillon , Chandigarh Data Recovery Labs [India]
Logical,Semi Physical And Physical Data Recovery
Website-> http://www.chandigarhdatarecovery.com
Top
 Profile  
 
pepe
 Post subject: Re: DT01ACA AND DT01ABA CROSS COMP.
PostPosted: December 17th, 2024, 3:12 
Offline

Joined: October 3rd, 2005, 0:40
Posts: 4753
Location: Hungary
there can be slight differences. sliders look the same, but who bothered measuring spring force yet? Anyway, they usually work for recovery, however, HGST is picky about preamp type too, so that may be another culprit to work around...

_________________
Adatmentés - Data recovery
Top
 Profile  
 
Amarbir[CDR-Labs]
 Post subject: Re: DT01ACA AND DT01ABA CROSS COMP.
PostPosted: December 17th, 2024, 3:22 
Offline
User avatar

Joined: August 15th, 2006, 3:01
Posts: 3522
Location: CDRLabs @ Chandigarh [ India ]
pepe wrote:
there can be slight differences. sliders look the same, but who bothered measuring spring force yet? Anyway, they usually work for recovery, however, HGST is picky about preamp type too, so that may be another culprit to work around...


Well,
i have never experienced hgst being picky about preamp .

_________________
Regards
Amarbir S Dhillon , Chandigarh Data Recovery Labs [India]
Logical,Semi Physical And Physical Data Recovery
Website-> http://www.chandigarhdatarecovery.com
Top
 Profile  
 
pepe
 Post subject: Re: DT01ACA AND DT01ABA CROSS COMP.
PostPosted: December 17th, 2024, 16:30 
Offline

Joined: October 3rd, 2005, 0:40
Posts: 4753
Location: Hungary
tried to swap heads between families? like F9, G9, H9?
heads are basically the same but FW fails on preamp id...
can be tricked btw, but still...
well, right, other brands might be picky too, in that sense :)

_________________
Adatmentés - Data recovery
Top
 Profile  
 
Amarbir[CDR-Labs]
 Post subject: Re: DT01ACA AND DT01ABA CROSS COMP.
PostPosted: December 18th, 2024, 2:36 
Offline
User avatar

Joined: August 15th, 2006, 3:01
Posts: 3522
Location: CDRLabs @ Chandigarh [ India ]
pepe wrote:
tried to swap heads between families? like F9, G9, H9?
heads are basically the same but FW fails on preamp id...
can be tricked btw, but still...
well, right, other brands might be picky too, in that sense :)


Hello,
Here we are taking about only " DT01ACA AND DT01ABA "

_________________
Regards
Amarbir S Dhillon , Chandigarh Data Recovery Labs [India]
Logical,Semi Physical And Physical Data Recovery
Website-> http://www.chandigarhdatarecovery.com
Top
 Profile  
 
pcimage
 Post subject: Re: DT01ACA AND DT01ABA CROSS COMP.
PostPosted: December 18th, 2024, 17:51 
Offline

Joined: November 29th, 2006, 10:08
Posts: 7864
Location: UK
fzabkar wrote:
I've heard that people have been able to use 7200RPM WD heads in 5400RPM WD drives and vice versa. Whilst I have no experience in head swaps, I would think that a head that was designed to fly at a particular height in a 7200RPM drive would fly lower in a 5400RPM drive, and vice versa.


FYI: I have used 5K1000-XXX donor heads in 7K1000-XXX series 2.5" HGST drives many times without issues.

_________________
PC Image Data Recovery
http://www.pcimage.co.uk

New!! HDD-PCB.COM for all your PCB and donor HDD requirements!
Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  Page 1 of 1
  [ 12 posts ] 

Main » Forums home » Conventional hard drives

All times are UTC - 5 hours [ DST ]

Who is online

Users browsing this forum: No registered users and 49 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Switch to mobile style
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group