All times are UTC - 5 hours [ DST ]




Post new topic Reply to topic  [ 14 posts ] 
Author Message
 Post subject: Samsug 860 EVO dead
PostPosted: May 1st, 2022, 14:29 
Offline

Joined: May 1st, 2022, 13:47
Posts: 9
Location: Italy
Hi guys, I'm new to the forum, my name is Davide, sorry for my poor English! I was fumbling in the computer case while it was on, and by mistake I moved the SSD cables, when i restarted the pc, the SSD is gone, not displayed in the bios, not even in disk management. I think I made a short circuit (?).
I wanted to ask if I could do something. I attach some photos


Attachments:
photo_2022-05-01_20-03-45.jpg
photo_2022-05-01_20-03-45.jpg [ 143.44 KiB | Viewed 11420 times ]
photo_2022-05-01_20-03-44.jpg
photo_2022-05-01_20-03-44.jpg [ 216.92 KiB | Viewed 11420 times ]
Top
 Profile  
 
 Post subject: Re: Samsug 860 EVO dead
PostPosted: May 1st, 2022, 16:24 
Offline
User avatar

Joined: September 8th, 2009, 18:21
Posts: 15463
Location: Australia
There is a 10-pin e-fuse above the SDRAM. Measure the voltages at its input and output pins.

_________________
A backup a day keeps DR away.


Top
 Profile  
 
 Post subject: Re: Samsug 860 EVO dead
PostPosted: May 2nd, 2022, 12:31 
Offline

Joined: May 1st, 2022, 13:47
Posts: 9
Location: Italy
Thanks for the quick reply. I wanted to ask you kindly, since I am not an expert, if you can tell me by marking on the photo which pin I should measure. Sorry but I can't go on :roll:


Top
 Profile  
 
 Post subject: Re: Samsug 860 EVO dead
PostPosted: May 2nd, 2022, 14:13 
Offline

Joined: May 1st, 2022, 13:47
Posts: 9
Location: Italy
Morpheus wrote:
Thanks for the quick reply. I wanted to ask you kindly, since I am not an expert, if you can tell me by marking on the photo which pin I should measure. Sorry but I can't go on :roll:
I add more detailed photo of the component


Attachments:
phot.jpg
phot.jpg [ 198.9 KiB | Viewed 11282 times ]
Top
 Profile  
 
 Post subject: Re: Samsug 860 EVO dead
PostPosted: May 2nd, 2022, 14:18 
Offline
User avatar

Joined: September 8th, 2009, 18:21
Posts: 15463
Location: Australia
Measure 5Vin and 5Vout. Use a screw hole as your ground reference.


Attachments:
e-fuse.jpg
e-fuse.jpg [ 120.32 KiB | Viewed 11281 times ]

_________________
A backup a day keeps DR away.
Top
 Profile  
 
 Post subject: Re: Samsug 860 EVO dead
PostPosted: May 3rd, 2022, 11:02 
Offline

Joined: May 1st, 2022, 13:47
Posts: 9
Location: Italy
I checked under a microscope and realized that it is burned, has a small burned bubble on top. Can that component be purchased?


Attachments:
20220503_170402.jpg
20220503_170402.jpg [ 2.1 MiB | Viewed 11168 times ]
20220503_163946.jpg
20220503_163946.jpg [ 2.79 MiB | Viewed 11169 times ]
Top
 Profile  
 
 Post subject: Re: Samsug 860 EVO dead
PostPosted: May 3rd, 2022, 12:56 
Offline
User avatar

Joined: September 8th, 2009, 18:21
Posts: 15463
Location: Australia
It's and STEF4S e-fuse:

http://www.hddoracle.com/viewtopic.php?f=100&t=1615

If there are no other problems, and if your PSU is OK, you can bridge 5Vin to 5Vout. Measure the voltages first, though.

_________________
A backup a day keeps DR away.


Top
 Profile  
 
 Post subject: Re: Samsug 860 EVO dead
PostPosted: May 3rd, 2022, 13:10 
Offline

Joined: May 1st, 2022, 13:47
Posts: 9
Location: Italy
Assuming the power supply is ok, with this bridge in the future can cause problems? Can you make some lines for me to figure out what to connect with what? Just to make no mistake, thanks


Top
 Profile  
 
 Post subject: Re: Samsug 860 EVO dead
PostPosted: May 3rd, 2022, 13:47 
Offline
User avatar

Joined: September 8th, 2009, 18:21
Posts: 15463
Location: Australia
I've marked the points on the photo. I don't know how much more I can tell you other than to join the two points. Be aware that the drive will work, but it will no longer be protected from overvoltages. Replace the IC with an STEF4S if you want continued protection.

That said, if you are unable to measure a voltage, then you might consider passing the task to someone else.

_________________
A backup a day keeps DR away.


Top
 Profile  
 
 Post subject: Re: Samsug 860 EVO dead
PostPosted: May 4th, 2022, 6:27 
Offline

Joined: May 1st, 2022, 13:47
Posts: 9
Location: Italy
I made the bridge and now it works! Is this https://it.aliexpress.com/item/1005003601615735.html?spm=a2g0o.productlist.0.0.356232b7OIg8Ca&algo_pvid=183833ff-27d0-4fe5-98c1-0ce6b767fd0f&algo_exp_id=183833ff-27d0-4fe5-98c1-0ce6b767fd0f-1&pdp_ext_f=%7B%22sku_id%22%3A%2212000026453060688%22%7D&pdp_npi=1%40dis%7CEUR%7C%7C3.69%7C%7C%7C%7C%7C%402100bb4916516598250055438e98ff%7C12000026453060688%7Csea


Top
 Profile  
 
 Post subject: Re: Samsug 860 EVO dead
PostPosted: May 4th, 2022, 13:50 
Offline
User avatar

Joined: September 8th, 2009, 18:21
Posts: 15463
Location: Australia
Yes, that looks like it (DFN package). I would prefer to buy it from a trusted source like Farnell, RS Online , Digikey, Mouser.

https://it.farnell.com/c/semiconduttori-circuiti-integrati/circuiti-integrati-di-gestione-di-potenza-pmic/controllori-hot-swap?st=stef4s
https://www.digikey.it/it/products/detail/stmicroelectronics/STEF4SPUR/4383954
https://www.mouser.it/ProductDetail/STMicroelectronics/STEF4SPUR?qs=DqCdCwOw4%2F72PHOKVsUxjg%3D%3D

_________________
A backup a day keeps DR away.


Top
 Profile  
 
 Post subject: Re: Samsug 860 EVO dead
PostPosted: May 5th, 2022, 11:16 
Offline

Joined: May 1st, 2022, 13:47
Posts: 9
Location: Italy
Ok i ordered on mouser.it ! When it arrives I will let you know if everything works! Thanks you soo much


Top
 Profile  
 
 Post subject: Re: Samsug 860 EVO dead
PostPosted: July 5th, 2022, 11:46 
Offline

Joined: May 1st, 2022, 13:47
Posts: 9
Location: Italy
I mounted the component, but now if I try it doesn't work :cry: can there be some other problem? Before, it worked with the bridge


Top
 Profile  
 
 Post subject: Re: Samsug 860 EVO dead
PostPosted: July 5th, 2022, 13:48 
Offline
User avatar

Joined: September 8th, 2009, 18:21
Posts: 15463
Location: Australia
Can you measure the voltages on each pin?

_________________
A backup a day keeps DR away.


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 14 posts ] 

All times are UTC - 5 hours [ DST ]


Who is online

Users browsing this forum: Google Feedfetcher and 32 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group