All times are UTC - 5 hours [ DST ]




Post new topic Reply to topic  [ 10 posts ] 
Author Message
 Post subject: Apple SSD Toshiba 656-0021B dead
PostPosted: January 11th, 2023, 9:31 
Offline

Joined: September 9th, 2020, 8:51
Posts: 12
Location: italy
Hello all,

I'm in need of some assistance with my SSD in the subject.
I saw a damaged capacitor (highlighted in red) , I tried to replace it but nothing changed.

Has anyone had a similar experience or know of a potential solution?
I've tried doing some research on my own, but I'm not really sure what the best course of action is. Any help would be greatly appreciated!

Thanks in advance.


Attachments:
20230111_124724.jpg
20230111_124724.jpg [ 2.99 MiB | Viewed 4164 times ]
Top
 Profile  
 
 Post subject: Re: Apple SSD Toshiba 656-0021B dead
PostPosted: January 11th, 2023, 12:31 
Offline
User avatar

Joined: September 8th, 2009, 18:21
Posts: 15461
Location: Australia
Are you able to access both sides of the SSD in a powered state? If so I could help you to measure the voltage test points.

_________________
A backup a day keeps DR away.


Top
 Profile  
 
 Post subject: Re: Apple SSD Toshiba 656-0021B dead
PostPosted: January 12th, 2023, 6:08 
Offline

Joined: September 9th, 2020, 8:51
Posts: 12
Location: italy
Hello,

thank you for your reply... yes, let's try...

Let me know voltage test point I can measure

Thanks a lot


Top
 Profile  
 
 Post subject: Re: Apple SSD Toshiba 656-0021B dead
PostPosted: January 12th, 2023, 11:58 
Offline
User avatar

Joined: September 8th, 2009, 18:21
Posts: 15461
Location: Australia
I need to see the other side of the board.

You need to measure the voltages between ground and each inductor. One is marked "R47" plus there are two unmarked ones on the other side.

These are the datasheets:

ISL8022, Renesas/Intersil, Dual 2A/1.7A Low Quiescent Current 2.25MHz Synchronous Buck Regulator, Vin = 2.8V - 5.5V, marking 8022, DFN-12:
https://www.intersil.com/content/dam/Intersil/documents/isl8/isl8022.pdf

ISL8025A, Renesas/Intersil, Synchronous Buck Regulator, 5A, Vin = 2.7V - 5.5V, marking 25AA, TQFN-16:
https://www.intersil.com/content/dam/Intersil/documents/isl8/isl8025-25a.pdf

_________________
A backup a day keeps DR away.


Top
 Profile  
 
 Post subject: Re: Apple SSD Toshiba 656-0021B dead
PostPosted: January 13th, 2023, 4:15 
Offline

Joined: September 9th, 2020, 8:51
Posts: 12
Location: italy
Hi,

here the other side of the board.

Thanks


Attachments:
20230112_171530.jpg
20230112_171530.jpg [ 3.12 MiB | Viewed 3973 times ]
Top
 Profile  
 
 Post subject: Re: Apple SSD Toshiba 656-0021B dead
PostPosted: January 13th, 2023, 5:00 
Offline

Joined: September 9th, 2020, 8:51
Posts: 12
Location: italy
The value of R47<->GND is 1,14V


Top
 Profile  
 
 Post subject: Re: Apple SSD Toshiba 656-0021B dead
PostPosted: January 13th, 2023, 6:00 
Offline

Joined: September 9th, 2020, 8:51
Posts: 12
Location: italy
n3dv3d wrote:
The value of R47<->GND is 1,14V


Attached measures of 8022 and 8025A

Thanks


Attachments:
8025A.jpg
8025A.jpg [ 35.14 KiB | Viewed 3954 times ]
8022.jpg
8022.jpg [ 20.95 KiB | Viewed 3954 times ]
Top
 Profile  
 
 Post subject: Re: Apple SSD Toshiba 656-0021B dead
PostPosted: January 13th, 2023, 13:04 
Offline
User avatar

Joined: September 8th, 2009, 18:21
Posts: 15461
Location: Australia
I expect they will be OK, but these are the other two supply voltages. Measure the voltage between each inductor and ground.


Attachments:
regs.jpg
regs.jpg [ 50.85 KiB | Viewed 3916 times ]

_________________
A backup a day keeps DR away.
Top
 Profile  
 
 Post subject: Re: Apple SSD Toshiba 656-0021B dead
PostPosted: January 16th, 2023, 5:31 
Offline

Joined: September 9th, 2020, 8:51
Posts: 12
Location: italy
Hi,

here the measure of inductors. Is it correct?

Thanks


Attachments:
regs.jpg
regs.jpg [ 26.17 KiB | Viewed 3734 times ]
Top
 Profile  
 
 Post subject: Re: Apple SSD Toshiba 656-0021B dead
PostPosted: January 16th, 2023, 13:24 
Offline
User avatar

Joined: September 8th, 2009, 18:21
Posts: 15461
Location: Australia
Those supplies look OK. The other tiny components could be load switches, in which case we should check their outputs. Unfortunately I can't discern their part markings, so I can't be of any more help.

That said, the fault is most likely a firmware panic due to bad NAND. If you really wish to exhaust all hardware possibilities, please tell me the markings on all the smaller ICs.

_________________
A backup a day keeps DR away.


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 10 posts ] 

All times are UTC - 5 hours [ DST ]


Who is online

Users browsing this forum: Google [Bot] and 20 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group