Discussions related to PC-3000
Please no pirated software here!
September 5th, 2011, 15:19
Seagate 7200.10, terminal output after head change. Any hints? Drive stays on busy mode.
---------------------------------------------------------------------------------------
MR
$SFI
AMR
$$$SFI
AMR
(P)SATA Reset
$SFI
AMR
$$$SFI
AMR
$$$SFI
AMR
$$$SFI
AMR
DiskAccess ReadSector EC=47 at ffffffff.00.0002
$SFI
AMR
$SFI
AMR
DiskAccess ReadSector EC=47 at ffffffff.00.0002
Read Ver Retrys
DiskAccess ReadSector EC=47 at ffffffff.00.0002
Read Ver Retrys
DiskAccess ReadSector EC=47 at ffffffff.00.0002
Read Ver Retrys
DiskAccess ReadSector EC=47 at ffffffff.00.0002
Read Ver Retrys
DiskAccess ReadSector EC=47 at ffffffff.00.0002
Read Ver Failure!
DiskAccess ReadSector EC=47 at ffffffff.00.022b
Failed sys sect. write! Nwt Er 00 RdWr 16645.00.022b
DiskAccess ReadSector EC=47 at ffffffff.00.0080
DiskAccess ReadSector EC=47 at ffffffff.00.0080
Unable To Load Overlay 01|000A
T>
------------------------------------------------------------------------------------------------------------
September 5th, 2011, 16:43
was it dropped initially? Did you swap heads "manually" or with a tool?
September 5th, 2011, 17:16
You still can try to initilize it using a loader.
September 5th, 2011, 17:46
CK wrote:was it dropped initially? Did you swap heads "manually" or with a tool?
Yes, according to the client it really was dropped. And the heads were changed "manually".
Last edited by
barak on September 5th, 2011, 17:55, edited 1 time in total.
September 5th, 2011, 17:48
dmarques wrote:You still can try to initilize it using a loader.
Ok, great. And please, the suitable loader I can find from where?
September 5th, 2011, 17:49
From another drive with same model and firmware at least.
September 5th, 2011, 17:54
dmarques wrote:From another drive with same model and firmware at least.
So I'm looking for a loader for Seagate 7200.10 with FW 3.AFD, please.
September 5th, 2011, 17:57
I'm not in the office, so I cannot check now. Will check tomorrow.
September 5th, 2011, 18:24
dmarques wrote:I'm not in the office, so I cannot check now. Will check tomorrow.
Great, thanks in advance.
September 7th, 2011, 2:09
CK wrote:was it dropped initially? Did you swap heads "manually" or with a tool?
Do you think the surface is damaged because of dropping?
September 8th, 2011, 1:36
Out of curiosity, have you noticed a wobble while manually rotating the platters? Also, upon powering, does it make a click sound or more of a chirp sound?
Thanks
September 15th, 2011, 6:19
labtech wrote:Out of curiosity, have you noticed a wobble while manually rotating the platters? Also, upon powering, does it make a click sound or more of a chirp sound?
Thanks
No noticeable wobbling. It's pretty much a kind of chirp.
September 20th, 2011, 21:40
Sent PM.
September 25th, 2011, 5:08
Case closed. The drive was recognized after some fiddling the screw and it is cloned totally. Thank you.
Powered by phpBB © phpBB Group.