HDD GURU FORUMS

Hello

Have a disk with this when i connect :
It can not show-me the SA FW Version
Anyone have this error ?


Techno mode key:
HDD geometry loading.................... : Ok
Cyl Count............................... : 81004
Head Count.............................. : 4
SPT..................................... : 900

RAM:
Zone allocation table................... : Ok
ROM version............................. : 15.BE.
SA FW version........................... : ......
Link table version...................... : 05.66.

Serial ROM:
Read ROM................................ : Ok
Heads configuration..................... : From map
Heads number............................ : 6
The number of heads in use.............. : 4
Disabled heads.......................... : Yes
Head map................................ : 0,1,4,5

Service area:
Modules table loading................... : Drive is not ready
Configuration loading................... : WD Techno Key Error Drive is not ready
Translation overlay checking (Copy 0)... : Not found in modules directory
Translation overlay checking (Copy 1)... : Not found in modules directory

Thanks
ZeBong

What about the modules?

Can you read/check them?

i think i have idea to find out which version it's.

pcimage wrote:What about the modules?

Can you read/check them?

i can not read them, it appear blank.

i also try to cut head by head but nothing happen.

networkpc3000 wrote:i think i have idea to find out which version it's.

So what do you think it is ?

Hi,

Modules table loading................... : Drive is not ready

Modules table NOT loaded!!! (module 41.rpm [~Dir.rpm])
At first Read (backup) all service tracks...

Mikippp

hi,

that´s the problem i can not see any module and i can not backup

At first Read (backup) all service tracks... (tracks not modules)
You can not read modules becouse modules table was NOT loaded!!!
Then read the manual... especially informations about module "ID=41h" and about "Utility extensions".

Mikippp

Thanks,

i go there and i dont see any backup off tracks.

ZeBong

Its in the test menu .

Hi try to make the backup off the tracks:

But i can not, what do you think the problem is :

Thanks


Reading service tracks
Into folder............................. : <HDD Profile>\Data\Tracks
Reading heads........................... : 0,1,4,5
WD Techno Read Error C/H/S: -1/0/0
WD Techno Read Error C/H/S: -1/0/1
Cyl -1; Head 0.......................... : Break
WD Techno Read Error C/H/S: -1/1/0
WD Techno Read Error C/H/S: -1/1/1
WD Techno Read Error C/H/S: -1/1/2
WD Techno Read Error C/H/S: -1/1/3
WD Techno Read Error C/H/S: -1/1/4
Cyl -1; Head 1.......................... : Break

Hi,
You use original PCB with original ROM ?
Did you try the head check?
wd1200bb-changed-rom-and-pcb-still-not-work-t7717.html

Mikippp

Mikippp wrote:Hi,
You use original PCB with original ROM ?
Did you try the head check?
wd1200bb-changed-rom-and-pcb-still-not-work-t7717.html

Mikippp

Yes,

Everything is original.

I think problem with head 1 .

Anyone have one disk to seel need the heads match

WD1200JB-00FUA0

ZeBong

Do you need a drive to work with a drive discussed above?

Hello,

This things happen today i turn on the disk and it can be detect byt the udma.

Techno mode key:
HDD geometry loading.................... : Ok
Cyl Count............................... : 15468
Head Count.............................. : 4
SPT..................................... : 900

RAM:
Zone allocation table................... : Ok
ROM version............................. : 15.BE.
SA FW version........................... : 15.BER
Link table version...................... : 05.66.

Serial ROM:
Read ROM................................ : Ok
Heads configuration..................... : From map
Heads number............................ : 6
The number of heads in use.............. : 4
Disabled heads.......................... : Yes
Head map................................ : 0,1,4,5

Service area:
Modules table loading................... : Ok (Copy 0)
Configuration loading................... : Ok
Master Password......................... : has not been set
User Password........................... : has not been set
Translation overlay checking............ : Ok


Also i start to make a copy with DE but it give ecc error,
Anyone can help on this ?

Thanks
ZeBong

You have to read it by head map and read the ones that do read and then work with the ones that don't read.

harddrivespecialist wrote:You have to read it by head map and read the ones that do read and then work with the ones that don't read.

Try to build a head maps but it give error.

Make a head test :

it gives OK,

Heads test
Cylinder to test........................ : -25
Heads to test........................... : 0,1,2,3
Head 0.................................. : Ok
Head 1.................................. : Ok
Head 4.................................. : Ok
Head 5.................................. : Ok



SA surface verification
Initial cylinder........................ : -1
Final cylinder.......................... : -20
Head.................................... : 0,1
Cyl -1 Head 0........................... : Errors : 0
Cyl -1 Head 1........................... : Errors : 0
Cyl -2 Head 0........................... : Errors : 0
Cyl -2 Head 1........................... : Errors : 0
Cyl -3 Head 0........................... : Errors : 0
Cyl -3 Head 1........................... : Errors : 0
Cyl -4 Head 0........................... : Errors : 0
Cyl -4 Head 1........................... : Errors : 0
Cyl -5 Head 0........................... : Errors : 0
Cyl -5 Head 1........................... : Errors : 0
Cyl -6 Head 0........................... : Errors : 0
Cyl -6 Head 1........................... : Errors : 0
Cyl -7 Head 0........................... : Errors : 0
Cyl -7 Head 1........................... : Errors : 0
Cyl -8 Head 0........................... : Errors : 2
--------------------------------------------------
Sectors :Error
--------------------------------------------------
304.....................................
319.....................................
--------------------------------------------------
Cyl -8 Head 1........................... : Errors : 0
Cyl -9 Head 0........................... : Errors : 0
Cyl -9 Head 1........................... : Errors : 0
Cyl -10 Head 0.......................... : Errors : 0
Cyl -10 Head 1.......................... : Errors : 0
Cyl -11 Head 0.......................... : Errors : 0
Cyl -11 Head 1.......................... : Errors : 0
Cyl -12 Head 0.......................... : Errors : 0
Cyl -12 Head 1.......................... : Errors : 0
Cyl -13 Head 0.......................... : Errors : 0
Cyl -13 Head 1.......................... : Errors : 0
Cyl -14 Head 0.......................... : Errors : 0
Cyl -14 Head 1.......................... : Errors : 0
Cyl -15 Head 0.......................... : Errors : 0
Cyl -15 Head 1.......................... : Errors : 0
Cyl -16 Head 0.......................... : Errors : 0
Cyl -16 Head 1.......................... : Errors : 0
Cyl -17 Head 0.......................... : Errors : 0
Cyl -17 Head 1.......................... : Errors : 0
Cyl -18 Head 0.......................... : Errors : 0
Cyl -18 Head 1.......................... : Errors : 0
Cyl -19 Head 0.......................... : Errors : 0
Cyl -19 Head 1.......................... : Errors : 0
Cyl -20 Head 0.......................... : Errors : 16
--------------------------------------------------
Sectors :Error
--------------------------------------------------
1.......................................
11......................................
15 -- 16................................
20 -- 21................................
25 -- 26................................
30 -- 31................................
35 -- 36................................
40 -- 41................................
45 -- 46................................
--------------------------------------------------
Cyl -20 Head 1.......................... : Errors : 24
--------------------------------------------------
Sectors :Error
--------------------------------------------------
1.......................................
10 -- 11................................
15 -- 16................................
17......................................Drive is not ready
20 -- 21................................
22......................................Drive is not ready
25 -- 26................................
27......................................Drive is not ready
30 -- 31................................
32......................................Drive is not ready
35 -- 36................................
37......................................Drive is not ready
40 -- 41................................
42......................................Drive is not ready
45 -- 46................................
47......................................Drive is not ready
--------------------------------------------------

SA surface verification completed