| HDD GURU FORUMS http://forum.hddguru.com/ |
|
| How to fix a MAXTOR 6E040L0 40GB IDE http://forum.hddguru.com/viewtopic.php?f=11&t=11266 |
Page 1 of 1 |
| Author: | zebong [ February 10th, 2009, 10:35 ] |
| Post subject: | How to fix a MAXTOR 6E040L0 40GB IDE |
Hi , need some help how to fix this drive. the sounds is like this : Attachment: Put the disk in safe mode and enter the utility: Attachment: NAR61EA0.jpg [ 37.38 KiB | Viewed 9709 times ] Attachment: NAR61EA0-1.jpg [ 77.46 KiB | Viewed 8626 times ] Attachment: NAR61EA0-2.jpg [ 13.79 KiB | Viewed 9706 times ] Attachment: NAR61EA0-3.jpg [ 73.38 KiB | Viewed 8630 times ] Thanks ZeBong |
|
| Author: | msurgeon [ February 10th, 2009, 13:15 ] |
| Post subject: | Re: How to fix a MAXTOR 6E040L0 40GB IDE |
From the sound of the drive, it appears that heads and/or media are bad. However, you can try the following: after loader loads, you should run 1) HDD ID reading (which it looks like you did) to make sure firmware number changes to end in 0, and 2) Run Initialize HDD/Initialize all which, if proper loader has loaded, will correctly ID the drive. You should try several loaders to see if you can reach this stage. At that point you can try to read SA. If unsuccessful with loader then try hotswap with same model. |
|
| Author: | harddrivespecialist [ February 10th, 2009, 13:32 ] |
| Post subject: | Re: How to fix a MAXTOR 6E040L0 40GB IDE |
You have to check head condition and fix SA |
|
| Author: | zebong [ February 16th, 2009, 12:39 ] |
| Post subject: | Re: How to fix a MAXTOR 6E040L0 40GB IDE |
Hi to all, I try the loader for this model but i can not work. Also do hot swap and dont work. How can i open this disk ... ? to check the Heads. Should i try more loaders i just have 3, if so can anyone send to me. Thanks ZeBong |
|
| Author: | zebong [ March 6th, 2009, 15:52 ] |
| Post subject: | Re: How to fix a MAXTOR 6E040L0 40GB IDE |
Afther open the disk, notice that the filter is very dirty, and the platte is like this: Attachment: MAXTOR.JPG [ 857.24 KiB | Viewed 8637 times ] |
|
| Author: | N.C. [ March 6th, 2009, 17:07 ] |
| Post subject: | Re: How to fix a MAXTOR 6E040L0 40GB IDE |
Case closed. I have some similar from N40P....  Janos |
|
| Author: | sadelgado [ May 26th, 2009, 9:11 ] |
| Post subject: | Re: How to fix a MAXTOR 6E040L0 40GB IDE |
How I Can to got this Utilitity load my LDR?? |
|
| Author: | N.C. [ May 26th, 2009, 10:36 ] |
| Post subject: | Re: How to fix a MAXTOR 6E040L0 40GB IDE |
This is the PC3000 UDMA on the pic. You need to buy it. Janos |
|
| Page 1 of 1 | All times are UTC - 5 hours [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|
