HDD GURU FORUMS

Data recovery and HDD repair discussions
http://forum.hddguru.com/

WD DENALI

http://forum.hddguru.com/viewtopic.php?f=11&t=21155

Page 1 of 1

WD DENALI

Posted: November 16th, 2011, 13:52
by sempre
Hi to all!
After an exchange of the HDD heads respond well ...

Denali

Techno mode key
Techno mode key......................... : Ok

RAM:
HDD Info reading........................ : Ok
Heads number............................ : 2
Cyl Count............................... : 128

ROM:
ROM reading............................. : Ok
ROM Data size........................... : 192 Kb
ROM version............................. : 08.2CD
ROM generation.......................... : 08.2CD
Link table version...................... : 02.14.
Consolidated ROM version................ : 0008002C

ROM Modules:
Flash ROM dir reading................... : Ok
Modules directory address............... : FIXED
Heads configuration..................... : by map
Heads number............................ : 2
Heads number in use..................... : 2
Switched off heads...................... : No
Heads map............................... : 0,1
ROM Firmware version.................... : 0008002C

Re: WD DENALI

Posted: November 17th, 2011, 8:45
by sempre
sempre wrote:Hi to all!
After an exchange of the HDD heads respond well ...

Denali

Techno mode key
Techno mode key......................... : Ok

RAM:
HDD Info reading........................ : Ok
Heads number............................ : 2
Cyl Count............................... : 128

ROM:
ROM reading............................. : Ok
ROM Data size........................... : 192 Kb
ROM version............................. : 08.2CD
ROM generation.......................... : 08.2CD
Link table version...................... : 02.14.
Consolidated ROM version................ : 0008002C

ROM Modules:
Flash ROM dir reading................... : Ok
Modules directory address............... : FIXED
Heads configuration..................... : by map
Heads number............................ : 2
Heads number in use..................... : 2
Switched off heads...................... : No
Heads map............................... : 0,1
ROM Firmware version.................... : 0008002C

Re: WD DENALI

Posted: November 17th, 2011, 16:48
by pcimage
It's in kernel mode, so no SA access.

Drive remains spinning after coming DRDY?

Re: WD DENALI

Posted: November 18th, 2011, 6:38
by sempre
pcimage wrote:It's in kernel mode, so no SA access. Ok!

Drive remains spinning after coming DRDY?

Yes!!

No SA acess normal mode...

Re: WD DENALI

Posted: November 18th, 2011, 9:07
by F_ARG
Hi!

Does it have original PCB?


Best regards

F.

Re: WD DENALI

Posted: November 20th, 2011, 6:53
by pcimage
sempre wrote:
pcimage wrote:It's in kernel mode, so no SA access. Ok!

Drive remains spinning after coming DRDY?

Yes!!

No SA acess normal mode...


What happens when you try normal mode?

Re: WD DENALI

Posted: November 21st, 2011, 7:59
by sempre
pcimage wrote:
sempre wrote:
pcimage wrote:It's in kernel mode, so no SA access. Ok!

Drive remains spinning after coming DRDY?

Yes!!

No SA acess normal mode...


What happens when you try normal mode?


echno mode key
Techno mode key......................... : Ok

RAM:
HDD Info reading........................ : Ok
Heads number............................ : 2
Cyl Count............................... : 128

Zone allocation table................... : HDDs RAM reading error - Device Error Detected: "VSCE PERM OVL NOT LOADED. LDR Upload is recomended"
ROM:
ROM reading............................. : Ok
ROM Data size........................... : 192 Kb
ROM version............................. : 08.2CD
ROM generation.......................... : 08.2CD
Link table version...................... : 02.14.
Consolidated ROM version................ : 0008002C

ROM Modules:
Flash ROM dir reading................... : Ok
Modules directory address............... : FIXED
Heads configuration..................... : by map
Heads number............................ : 2
Heads number in use..................... : 2
Switched off heads...................... : No
Heads map............................... : 0,1
ROM Firmware version.................... : 0008002C

Service area:
SA dir reading.......................... : Unknown error. Code(0)
SA Access............................... : NONE

Configuration reading................... : Module 02 not found

Upload LDR ERROR => OVM ERR NOT COMPATIBLE

Re: WD DENALI

Posted: November 22nd, 2011, 12:20
by hddguy
sempre wrote:Upload LDR ERROR => OVM ERR NOT COMPATIBLE


You have alternative compatible loader?

Re: WD DENALI

Posted: November 22nd, 2011, 17:28
by Nick_CT
I had the same issue with a Denali recently, same behaviour after headswap. Used a loader and got access to SA and all data.

Re: WD DENALI

Posted: November 23rd, 2011, 6:43
by sempre
hddguy wrote:
sempre wrote:Upload LDR ERROR => OVM ERR NOT COMPATIBLE


You have alternative compatible loader?

Not..

Please send me Loader!

Hdd model WD1600BEVT-75ZCT2

Re: WD DENALI

Posted: November 23rd, 2011, 10:04
by northwind
I looked but i only have 00zct0 and 22zct0 available. :(

Re: WD DENALI

Posted: November 23rd, 2011, 10:08
by hddguy
Does HD remain powered? IF so select 'View Module 90 information' and it should give to you the SA version.

If ROM is native then version is 0008002C. Is PCB/ROM native?

Re: WD DENALI

Posted: November 23rd, 2011, 10:23
by Nick_CT
Got lots from ZC family but not 0008002C. Sorry.

Re: WD DENALI

Posted: November 24th, 2011, 1:31
by GreyDKang
Try this resource.
http://files.hddguru.com/download/PC-3000-UDMA%20Support/WDC%20Marvell%20family%20utility/Denali/WD1600BEVT-00ZCT0%2011.01A11%20WD-WXE409PL5076.rar

Re: WD DENALI

Posted: April 26th, 2012, 4:51
by selftest
Backup Rom and use recovery Rom function. If still can't not identify, use LDR loading function.

Re: WD DENALI

Posted: April 26th, 2012, 6:11
by hddguy
selftest wrote:Backup Rom and use recovery Rom function. If still can't not identify, use LDR loading function.


From what I can see ROM seems native, and LDR not an option because no compatible version is available...

Hotswap and read patient 11.rpm could be option, but post is very old now...
All times are UTC - 5 hours [ DST ]
Page 1 of 1
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
http://www.phpbb.com/