| HDD GURU FORUMS http://forum.hddguru.com/ |
|
| WD Scorpio Blue 2.5 http://forum.hddguru.com/viewtopic.php?f=11&t=26486 |
Page 1 of 1 |
| Author: | sosrecup [ July 24th, 2013, 2:51 ] |
| Post subject: | WD Scorpio Blue 2.5 |
Hello, I have a WD 2.5" Scorpio Blue (Model WD5000BEVT-00A0RT0). When I connect it to PC3000, it is recognized, it reaches readiness but with errors. When the drive spin, I can hear an strange sound. When I run the utility, the model in not read and when I choose the model Scoprio, and I get the logs bellow: ############################## RAM: HDD Info reading........................ : Ok Heads number............................ : 4 Cyl Count............................... : 256 Zone allocation table................... : HDDs RAM reading error - Device Error Detected: "VSCE PERM OVL NOT LOADED. LDR Upload is recomended" ROM: ROM reading............................. : Ok ROM Data size........................... : 256 Kb ROM version............................. : 16.0SW ROM generation.......................... : 16.0SW Link table version...................... : 07.17. Consolidated ROM version................ : 0016000S ROM Modules: Head Map Reading Error.................. : Head map check sum error ROM Firmware version.................... : Service area: SA dir reading (ID)..................... : DISK SERVO SPINDLE SPINUP ERROR Configuration reading................... : Module 02 not found ########################### Any procedure or solution to resolve the problem please? Kind regards, |
|
| Author: | pcimage [ July 24th, 2013, 17:31 ] |
| Post subject: | Re: WD Scorpio Blue 2.5 |
Sounds like you are using pc3000 pci version, not UDMA. |
|
| Author: | sosrecup [ July 25th, 2013, 4:47 ] |
| Post subject: | Re: WD Scorpio Blue 2.5 |
Hello All, Many thanks for your help. Yes I'm using PC3000 PCI. I hear 5 times a quit sound then the sound stop (I'll check again if the drive continue to spin) Kind regards, |
|
| Author: | sosrecup [ July 25th, 2013, 9:08 ] |
| Post subject: | Re: WD Scorpio Blue 2.5 |
The drive stop spinning after I hear 5 times a quit sound. It should be a bad heads. |
|
| Author: | sosrecup [ July 25th, 2013, 18:08 ] |
| Post subject: | Re: WD Scorpio Blue 2.5 |
If it was stiction or spindle, the drive never reaches readiness. Correct me if I'm wrong. |
|
| Author: | pcimage [ July 26th, 2013, 2:58 ] |
| Post subject: | Re: WD Scorpio Blue 2.5 |
sosrecup wrote: The drive stop spinning after I hear 5 times a quit sound. It should be a bad heads. Yes, bad heads. |
|
| Author: | sosrecup [ July 26th, 2013, 3:19 ] |
| Post subject: | Re: WD Scorpio Blue 2.5 |
I started the drive in normal mode and in safe mode. |
|
| Author: | PlatinumDataRecovery [ July 26th, 2013, 4:03 ] |
| Post subject: | Re: WD Scorpio Blue 2.5 |
Most likely read/write heads are damaged. |
|
| Author: | jignesh [ July 26th, 2013, 4:44 ] |
| Post subject: | Re: WD Scorpio Blue 2.5 |
sosrecup wrote: Hello, I have a WD 2.5" Scorpio Blue (Model WD5000BEVT-00A0RT0). When I connect it to PC3000, it is recognized, it reaches readiness but with errors. When the drive spin, I can hear an strange sound. When I run the utility, the model in not read and when I choose the model Scoprio, and I get the logs bellow: ############################## RAM: HDD Info reading........................ : Ok Heads number............................ : 4 Cyl Count............................... : 256 Zone allocation table................... : HDDs RAM reading error - Device Error Detected: "VSCE PERM OVL NOT LOADED. LDR Upload is recomended" ROM: ROM reading............................. : Ok ROM Data size........................... : 256 Kb ROM version............................. : 16.0SW ROM generation.......................... : 16.0SW Link table version...................... : 07.17. Consolidated ROM version................ : 0016000S ROM Modules: Head Map Reading Error.................. : Head map check sum error ROM Firmware version.................... : Service area: SA dir reading (ID)..................... : DISK SERVO SPINDLE SPINUP ERROR Configuration reading................... : Module 02 not found ########################### Any procedure or solution to resolve the problem please? Kind regards, Hi Dear Friend Sosrecup Dear Friend Read The Diag Carefully. Head Map Reading Error.................. : Head map check sum error That Mean Problem In If Drive Dont Get Head Map Then Its Not Reach Readyness. Not Able To Read Information. And No When No Information Awailable U Know What Happend. SA dir reading (ID)..................... : DISK SERVO SPINDLE SPINUP ERROR Configuration reading................... : Module 02 not found Its Caused By Bad ReadWrite Head. But When U Change The Head First Try HOTSWAP Method I Have Many Time Its Happend That I Recover Data From Hot Swap Tipical This Type Of Cases. Your Friend Jignesh Pankhania |
|
| Page 1 of 1 | All times are UTC - 5 hours [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|