Hello,
Can anyone guide me for shorting point of 100717520 Rev B.
Pic of PCB attached

Thanks in advance

15+16 or 17+18

contacts 16-18 on J4
odd the top row, the lower even

17+18 Worked but with following error
Boot 0x40M
Spin Up[LBA=0x000042F9]N02020C20o0o0o0o0o0o0o0o0[LBA=0x000042F9]NO1111[LBA=0x00066E3B]N01010C20o0o0o0o0o0o0o0o0[LBA=0x00066E3B]NO1111[LBA=0x00028F1D]N01020C10o0o0o0o0o0o0o0o0[LBA=0x00028F1D]NO1111[LBA=0x0008BA5F]N01010C10o0o0o0o0o0o0o0o0[LBA=0x0008BA5F]NO1111
SimError - Remaining in BootFW
Perform a double download without a power cycle

Terminal output at power on

Boot 0x40M
Spin Up[LBA=0x000042F9]N02020C20o0o0o0o0o0o0o0o0[LBA=0x000042F9]NO1111[LBA=0x00066E3B]N01010C20o0o0o0o0o0o0o0o0[LBA=0x00066E3B]NO1111[LBA=0x00028F1D]N01020C10o0o0o0o0o0o0o0o0[LBA=0x00028F1D]NO1111[LBA=0x0008BA5F]N01010C10o0o0o0o0o0o0o0o0[LBA=0x0008BA5F]NO1111
SimError - Remaining in BootFW
Perform a double download without a power cycle

You are shorting the drive to early it's all about timing with the Seagate DM drives.

By the way what's the problem with the drive?

_________________
Web: https://www.day1data.de

Hello,

HDD remains in bsy state.
No buzz/no clicking/motor not spin down.

At power on remains busy & terminal output is

Boot 0x40M
Spin Up
Trans.

Spin Up
SpinOK
SnapshotEventOccurred( SNAPSHOT_INITIAL_VALUES ).
(P) SATA Reset

Tried motor isolation method but not worked.
In short circuit method give following output (HDD goes in ready state)

Boot 0x40M
Spin Up[LBA=0x000042F9]N01020C10o0o0o0o0o0o0o0o0[LBA=0x000042F9]NO1111[LBA=0x00066E3B]N01010C10o0o0o0o0o0o0o0o0[LBA=0x00066E3B]NO1111[LBA=0x00028F1D]N01020C10o0o0o0o0o0o0o0o0[LBA=0x00028F1D]NO1111[LBA=0x0008BA5F]N01010C20o0o0o0o0o0o0o0o0[LBA=0x0008BA5F]NO1111
SimError - Remaining in BootFW
Perform a double download without a power cycle

and after that if i restart utility without re-power it detects

Model : ST2000DM001
Firmware : SC48
Capacity : 3.86 GB (8 089 950)

So now I'd go in, edit module 93 to disable all the auto reallocation and idle activities so it'll start up normally going forward. Then try to figure out why it's not showing correct capacity, maybe it will after power cycle.

_________________
Data Medics - Hard Drive, SSD, and RAID Data Recovery Service Company

Hello
Need Loader for this HDD ST2000DM001 FW SC48
Can anyone have?

Thanks in advance

Before trying loader, see if you can read system files through terminal and see if any critical ones are damaged.

Jared ,
Sir I Saw a Few Posts of Spildit Where He Says That any Times We Have To Set These Settings Back To Default State .In My Case i Follow the Procedure As You stated .Right Now i am working on a ST3500620AS Moose Family With Dell DE12 Firmware [ Thats Buggy ] But My Drive Cloned Well Only 6203 Not readable Sectors And Approx 57201 Skipped Sectors That i Am Still Working On Slowly On PC3K

_________________
Regards
Amarbir S Dhillon , Chandigarh Data Recovery Labs [India]
Logical,Semi Physical And Physical Data Recovery
Website-> http://www.chandigarhdatarecovery.com

hello,

i am not able to read any of system files.

Well,
Please Let Us Know What All Tools You Have So That Suggestions Pour In

_________________
Regards
Amarbir S Dhillon , Chandigarh Data Recovery Labs [India]
Logical,Semi Physical And Physical Data Recovery
Website-> http://www.chandigarhdatarecovery.com