HDD GURU FORUMS
http://forum.hddguru.com/

Help!!! WD400- WD400BB-75EA0 - PC3K can not access it yet
http://forum.hddguru.com/viewtopic.php?f=11&t=33380		 Page 1 of 1
Author:  olinyer [ April 29th, 2016, 23:06 ]
Post subject:  Help!!! WD400- WD400BB-75EA0 - PC3K can not access it yet
Hi,

Help... Need your guidance.

HDD western digital WD400- WD400BB-75EA0

Start spinning and HDD is making high trebele sound.

I am getting this error as soon as I run autodetect or run utility.
Error:
1. PIO Register Access TimeOut
2. HDD Readyness Timeout (10000)
3. Techno key error

Attached pictures.

Thank you for the guidance.

Best Regards,

Attachments:
File comment: error trying autodetect
Techno Key Error.png
Techno Key Error.png [ 185.72 KiB | Viewed 11392 times ]
File comment: error trying autodetect or run utility
HDD Readyness Timeout 10000.png
HDD Readyness Timeout 10000.png [ 175.01 KiB | Viewed 11392 times ]
File comment: error trying autodetect or run utility
PIO Register Access TimeOut.png
PIO Register Access TimeOut.png [ 137.13 KiB | Viewed 11392 times ]
Author:  olinyer [ April 30th, 2016, 0:23 ]
Post subject:  Re: Help!!! WD400- WD400BB-75EA0 - PC3K can not access it ye
It is showing Drive is not ready and did a research on forum and people is saying it might be translator issue ending in PCB problem.

Since is not accessible yet as it is I can not do some tips AceLab suggested.

some pictures attached of errors

Attachments:
test read.png
test read.png [ 124.65 KiB | Viewed 11385 times ]
HD Self Test Long.png
HD Self Test Long.png [ 157.13 KiB | Viewed 11385 times ]
drive is not ready.png
drive is not ready.png [ 142.89 KiB | Viewed 11385 times ]
Author:  northwind [ April 30th, 2016, 3:38 ]
Post subject:  Re: Help!!! WD400- WD400BB-75EA0 - PC3K can not access it ye
Have you put the jumper in place?
Instead of drd dsc all registers will flash as per your 3rd pic, if you didn't.
Also why are you trying to SS the drive? :o
Author:  ibcho [ April 30th, 2016, 5:28 ]
Post subject:  Re: Help!!! WD400- WD400BB-75EA0 - PC3K can not access it ye
make sure jumper settings on the hard drive is master
Author:  ddrecovery [ April 30th, 2016, 9:18 ]
Post subject:  Re: Help!!! WD400- WD400BB-75EA0 - PC3K can not access it ye
Tell us more about the sound the drive makes as mentioned in your first post. Is it a high pitched 'ringing' sound. Can you post a recording?
Author:  FileSavers [ April 30th, 2016, 10:48 ]
Post subject:  Re: Help!!! WD400- WD400BB-75EA0 - PC3K can not access it ye
In WD drives, all jumpers off are required for master.

If it's making noises, the heads could be making contact with the platters. Be very careful.

Can you get access to firmware modules? If so, start by reading the firmware modules into the PC-3000. Then you need to determine which firmware modules are damaged.

If you don't have access to firmware then you may need to put the hard drive in safe mode and turn all heads off except head 0 in RAM in order for you to get access to the firmware. If that does not work, you can try eliminating all heads except head 1. Again, once you gain access to the firmware, you will need to read all copies of the firmware into the PC-3000 and determine which ones are damaged. You may end up needing a very close match donor drive that will allow you to perform hot swap / smart hot swap to gain access to data.
Author:  ddrecovery [ April 30th, 2016, 11:00 ]
Post subject:  Re: Help!!! WD400- WD400BB-75EA0 - PC3K can not access it ye
Welcome to the forum Mr J :-)
Author:  olinyer [ May 3rd, 2016, 21:26 ]
Post subject:  Re: Help!!! WD400- WD400BB-75EA0 - PC3K can not access it ye
Hi,

You guys rock.

I was able to put the jumpers and able to recovered the data.

You guys rock again.

Thank you a lot for your time.

Best regards,
Author:  Amarbir[CDR-Labs] [ May 4th, 2016, 0:07 ]
Post subject:  Re: Help!!! WD400- WD400BB-75EA0 - PC3K can not access it ye
ddrecovery wrote:
Welcome to the forum Mr J :-)



DDrecovery ,
Is This jol ?
Author:  ddrecovery [ May 4th, 2016, 12:44 ]
Post subject:  Re: Help!!! WD400- WD400BB-75EA0 - PC3K can not access it ye
Amarbir[CDR-Labs] wrote:
ddrecovery wrote:
Welcome to the forum Mr J :-)

DDrecovery ,
Is This jol ?

Hey Amarbir, no its another person.
Page 1 of 1 All times are UTC - 5 hours [ DST ]
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
http://www.phpbb.com/