| HDD GURU FORUMS http://forum.hddguru.com/ |
|
| HELP!!! SSD Micro!!! http://forum.hddguru.com/viewtopic.php?f=11&t=34560 |
Page 1 of 1 |
| Author: | olinyer [ November 23rd, 2016, 22:07 ] |
| Post subject: | HELP!!! SSD Micro!!! |
Hi, I hope you are doing great. I have this SSD Storage Micro of 256GB (Lingston Technology) i have connected to a adapter SSD to SATA, it is very hot and PC3000 wont autodetect. Not sure next steps and it would be great a suggestion. Thank you for the help. Best regards, |
|
| Author: | F_ARG [ November 24th, 2016, 14:15 ] |
| Post subject: | Re: HELP!!! SSD Micro!!! |
Hi olinyer, Have you got a picture of it? Which part is getting hot? Main controller, memories? Best F |
|
| Author: | fzabkar [ November 24th, 2016, 14:23 ] |
| Post subject: | Re: HELP!!! SSD Micro!!! |
A photo of the adapter would be advisable, IMHO. It could be that the wrong adapter is being used. |
|
| Author: | olinyer [ November 24th, 2016, 15:10 ] | ||||
| Post subject: | Re: HELP!!! SSD Micro!!! | ||||
adding pic. the memories (two NAND Chips) are the one getting very hot i thought in the kind of adapter as well thank you for the help. Best regards,
|
|||||
| Author: | F_ARG [ November 24th, 2016, 16:04 ] |
| Post subject: | Re: HELP!!! SSD Micro!!! |
Hello! I can t realize looking at the pictures...but were the memories reworked (unsoldered and re-soldered)? Only 2 of the 4 memories are getting hot? Best, F |
|
| Author: | fzabkar [ November 24th, 2016, 17:12 ] |
| Post subject: | Re: HELP!!! SSD Micro!!! |
Here are photos of the adapter: http://cdn1.image-tmart.com/prodimgs_v2/8/8101/0925/81010925/M817-mSATA-SSD-to-25-SATA-Adapter-Card-25cm_800x800.jpg?1388195215 (component side) https://contestimg.wish.com/api/webimage/54002853ecdd3054d195a166-4-large.jpg (back) The voltage at the tab of U1 (LT1084-33) should be +3.3V. AFAICT, the SSD (Kingston SMSR150S3/256G mSATA) is a RAID with a separate SSD on each side.
Elpida EDJ2116DEBG 2Gbit DDR3 SDRAM 2 x Toshiba TH58TEG8DDJBA82 NAND flash (64GB ?) The adapter expects to see a single SSD. Therefore I would be very concerned with the pinout. Perhaps it is non-standard? I would determine the ground pins with a multimeter, and also confirm the +3.3V pins by testing for continuity with U1. EDJ2116DEBG, Elpida, 2Gbits DDR3 SDRAM, 128Mwords x 16bits, 1.5V: http://tabreview.ru/content/pdf_docs/El ... G_DJ_F.pdf LT1084-33, Linear Tech, 5A, 3.3V, LDO Regulator: http://www.farnell.com/datasheets/1941079.pdf PS3108-S8 product brief: http://www.phison.com/English/newProductView.asp?ID=237&SortID=63
Built-in Regulator that supports 3.3V/1.8V Flash I/O |
|
| Page 1 of 1 | All times are UTC - 5 hours [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|
