| HDD GURU FORUMS http://forum.hddguru.com/ |
|
| Seagate Mobile HDD ST1000LM035 Rom Reading failure http://forum.hddguru.com/viewtopic.php?f=11&t=42486 |
Page 2 of 2 |
| Author: | pepe [ June 21st, 2022, 16:55 ] |
| Post subject: | Re: Seagate Mobile HDD ST1000LM035 Rom Reading failure |
yes, if you don't get any output over serport, then there is likely some hw damage. Fix that first or move rom chip to a working pcb. pepe |
|
| Author: | terminator2 [ June 26th, 2022, 1:44 ] |
| Post subject: | Re: Seagate Mobile HDD ST1000LM035 Rom Reading failure |
pepe wrote: yes, if you don't get any output over serport, then there is likely some hw damage. Fix that first or move rom chip to a working pcb. pepe Yes there could be internal track or other electronic issue. Unfortunately manual chip reading is not possible so I have finally given up. Thanks a lot. |
|
| Author: | pepe [ June 26th, 2022, 7:43 ] |
| Post subject: | Re: Seagate Mobile HDD ST1000LM035 Rom Reading failure |
how about moving the rom chip to a known good pcb? |
|
| Author: | terminator2 [ June 27th, 2022, 10:02 ] |
| Post subject: | Re: Seagate Mobile HDD ST1000LM035 Rom Reading failure |
pepe wrote: how about moving the rom chip to a known good pcb? Hi pepe Unfortunately I can't remove ROM from 2.5" disk PCB (can only desolder TSOP type desktop roms) . Actually I don't know which type of ROM chip this model has . |
|
| Author: | digisupport [ June 27th, 2022, 12:49 ] | ||
| Post subject: | Re: Seagate Mobile HDD ST1000LM035 Rom Reading failure | ||
terminator2 wrote: pepe wrote: how about moving the rom chip to a known good pcb? Hi pepe Unfortunately I can't remove ROM from 2.5" disk PCB (can only desolder TSOP type desktop roms) . Actually I don't know which type of ROM chip this model has . ROM chip is typical serial flash but in a WLCSP-8 P8 package. Tiny but possible to move or read via external programmer.
|
|||
| Author: | terminator2 [ June 28th, 2022, 2:58 ] |
| Post subject: | Re: Seagate Mobile HDD ST1000LM035 Rom Reading failure |
digisupport wrote: terminator2 wrote: pepe wrote: how about moving the rom chip to a known good pcb? Hi pepe Unfortunately I can't remove ROM from 2.5" disk PCB (can only desolder TSOP type desktop roms) . Actually I don't know which type of ROM chip this model has . ROM chip is typical serial flash but in a WLCSP-8 P8 package. Tiny but possible to move or read via external programmer. Thanks a lot   I will give it a try |
|
| Author: | San Ps [ October 5th, 2022, 2:41 ] |
| Post subject: | Re: Seagate Mobile HDD ST1000LM035 Rom Reading failure |
whats the final solution for it? i m having same case |
|
| Author: | Banky [ November 2nd, 2022, 11:35 ] | ||
| Post subject: | Re: Seagate Mobile HDD ST1000LM035 Rom Reading failure | ||
I have a similar issue here with a Seagate with Model No. ST1000LM035 FW: RKM2 When I Power on Drive I get the following error Boot0x80M LED:0x000000BB FAddr:0x00005807 When I tried ROM via Terminal I get the following error.. Boot Code: Can not get the current address! I was able to Read ROM Via Programmer and Write to Donor PCB, still didn't work, and did not Power any other PCB. I tried to import RAP, CAP SAP and IAP from Donor ROM.. it gives following error, Boot Code: Can not get current address! I called ACELAB TS for help, I was told "BootFW segment is damaged. We can not fix this problem" I have attached the Original ROM read from Programmer. If anyone can help check it out.. Thank you
|
|||
| Page 2 of 2 | All times are UTC - 5 hours [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|
