| HDD GURU FORUMS http://forum.hddguru.com/ |
|
| Seagate Rosewood LXM3 need firmware backup http://forum.hddguru.com/viewtopic.php?f=11&t=42816 |
Page 1 of 1 |
| Author: | ccc [ October 21st, 2022, 5:49 ] |
| Post subject: | Seagate Rosewood LXM3 need firmware backup |
Hi guys I have this disk ,ST1000LM049-2GH172-LXM3, that came to me with this error: Code: Boot 0x80M Rst 0x80M Srv DETCR init 0x0000 FTU PrgF (P) SATA Reset RAW OFF PASS (DOS Table) Worst Count: 00000000 At SU: FFFFFFFF NT: 00000000 OT: 00000000 LED:0x000000BD FAddr:0x0000783A LED:0x000000BD FAddr:0x0000783A LED:0x000000BD FAddr:0x0000783A Boot 0x80M Tech Unlock Handshake: 0xB3CEBE38 Reply: Rst 0x80M Srv DETCR init 0x0000 FTU (1Ah)-Serial Port Not Ready PrgF (P) SATA Reset RAW OFF PASS (DOS Table) Worst Count: 00000000 At SU: FFFFFFFF NT: 00000000 OT: 00000000 LED:0x000000BD FAddr:0x0000783A LED:0x000000BD FAddr:0x0000783A LED:0x000000BD FAddr:0x0000783A To enter terminal I have tried many things: play with HM in Rom, short on different boot times, play with options in ROM, loader, etc. No way I can enter terminal or get RDY over ATA because all I get is LED: BD error in the end(BSY on ATA of course). Searching on net for fw backup result in 0 responses. I have managed to temporally get 2 disks with the same fw, LXM3, but without luck, the overlays are build in 2017 compared with the pacient disk that have overlays build in 2018. So the loaders from those 2 donors was useless. What I need is a LXM3 fw backup, more exactly sys file 20D or mod 3D or a loader with this parameters: Code: CODE info ######### Bank 0 ProdType................. : RX22.LIM1QBF Controller FW Rev........ : 04130215 Customer Release......... : LXM3 Changelist............... : 01457828 Build date / time........ : 4/13/2018 2:15:28 AM Package Global ID........ : 00503762 Package Builder ID....... : Build Rev................ : Package Rev.............. : CD2813 Pkg P/N.................. : 100836332 Servo FW................. : 7889 / ---- / ---- / ---- Package Version.......... : RX22.LIM1QBF.CD2813.LXM3 Pkg CFW Ver.............. : RX22.LIM1QBF.01457828.00503762 Family Rosewood AE. Thanks Regards |
|
| Author: | unknown [ October 21st, 2022, 9:31 ] |
| Post subject: | Re: Seagate Rosewood LXM3 need firmware backup |
I think it's all about the timing of shorting the read-channel after handshake. |
|
| Author: | ccc [ October 22nd, 2022, 5:12 ] |
| Post subject: | Re: Seagate Rosewood LXM3 need firmware backup |
This one is more stubborn than a monkey.......I tried shorting at different moments of booting but after millions of RECOV servo and Failed servo messages it always sudden go to LED:BD message. I also manage to extract the overlay from a LXM4 firmware update package, I can get to terminal and get RDY on ATA but, of course, because of overlay incompatibility, I can't do anything in firmware , I have only sector access on ATA. It's good but at first bad sector, and it has a lot, it goes to a pending operation and I can't stop it , except a power ON/OFF. It could be destructive so I want to access fw first to edit hdd ID and after that to start copying data. Rgds |
|
| Page 1 of 1 | All times are UTC - 5 hours [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|