Wanted WD10EAVS-00D7B0

[louisloo99]

Hi

Anybody has this Western Digital Cavair 1.0TB

Model No. WD10EAVS-00D7B0
DCM HHNNHV2MFB
R/N 701537
Date: 03 June 2008

Pls PM me if you have.

Tks
Louis

[harddrivespecialist]

You need a whole drive or PCB?

[networkpc3000]

hi,
i can help. please contact me by email or MSN if need. thanks.

[Eric Lee]

Hi,

We have this kinds of working PCB in stock, but for this kinds of PCBs, you need to reprogram rom in main chip.

Thanks
Eric

[louisloo99]

You need a whole drive or PCB?

i'm looking for the whole drive with the PCB..my first Data Recovery project...

[harddrivespecialist]

You need a whole drive or PCB?

i'm looking for the whole drive with the PCB..my first Data Recovery project...

Good luck!

[networkpc3000]

hi,
please contact me by email. i need more detail and i could help. thanks.

[louisloo99]

Dear All

My friends advise that I should look for the PCB replacement, not the whole drive.

Kindly advise if you have this replacement..for WD10EAVS-00D7B0.
PCB No. 2060 701537 004 REV A

pls post reply or PM me.

Tks
Louis

Attachments

[fzabkar]

My friends advise that I should look for the PCB replacement, not the whole drive.

Read this thread:
verbatim-western-digital-1tb-ext-drive-not-powering-t14369.html

Does your board have an 8-pin serial EEPROM chip at location U12 below the Marvell MCU (big "M")?

If not, then you will probably need to transfer the internal ROM contents of the Marvell chip from patient to donor. A straight board swap won't work.

There are companies offering a ROM transfer a service for $10, if you buy a PCB from them.

[louisloo99]

The EEPROM data is most probably in the MCU. I think the WD Doctor will be able to read the data in ROM and transfer the data over..

Do you use the P3000 or the Salvation Data Suite? which is better?

I just need the PCB replacement.

thanks

[fzabkar]

The EEPROM data is most probably in the MCU. I think the WD Doctor will be able to read the data in ROM and transfer the data over..

Do you use the P3000 or the Salvation Data Suite? which is better?

I just need the PCB replacement.

thanks

Sorry, I mistook you for an end user.

As for the DR products, I use neither. I'm not a DR guy.

[louisloo99]

No problem fzabkar...you are just being helpful..
I am still new and appreciate all the help.

Do you have the PCB that I am looking for?

[fzabkar]

Do you have the PCB that I am looking for?

No, sorry.

[networkpc3000]

hi,
i have it in stock. and can help you program original FW into good PCB if you can send file of ROM data to me.

[louisloo99]

i have it in stock. and can help you program original FW into good PCB if you can send file of ROM data to me.

Thanks for your offer to program for me...the joy is doing it myself and troubleshooting. and getting the experience at the same time...hehe..
Can you give me a quote and also send me a high quality picture of the chips and back of the PCB..

Tks
Louis

[networkpc3000]

yeah. i can. but why you had to match with chip and label?

[louisloo99]

actually, it is not a must...but if the chip can be the same,,better still right..because i check with another vendor, but he ask to give him the chip number also,,which i thot the same as you..why need to match the chip and the label..but i just gave him.

[networkpc3000]

hi,
sent them to you by email already. do you think vendor which you mention is pro? or just vendor only?

[louisloo99]

my customer has suddenly decided to take back his disk..already more than a month..sorry guys for your trouble..