Here som pics from the Hdd and Pcb
| Attachments: |
|
Schijf2.JPG [ 121.25 KiB | Viewed 10701 times ] |
|
Schijf1.JPG [ 128.65 KiB | Viewed 10701 times ] |
| HDD GURU FORUMS http://forum.hddguru.com/ |
|
| Need pcb WD2500AAJS http://forum.hddguru.com/viewtopic.php?f=15&t=20741 |
Page 1 of 1 |
| Author: | driver3 [ October 6th, 2011, 16:25 ] |
| Post subject: | Need pcb WD2500AAJS |
Hello Everyone I'm looking for a PCB-WD2500AAJS 60M0A1 P/N 484053-002 2060-701590-001 REV-A Western digital Blue caviar Thnx |
|
| Author: | pcimage [ October 7th, 2011, 2:50 ] |
| Post subject: | Re: Need pcb WD2500AAJS |
Post a clear pic of the component side of the bad PCB please. |
|
| Author: | driver3 [ October 7th, 2011, 4:15 ] | |||
| Post subject: | Re: Need pcb WD2500AAJS | |||
Here som pics from the Hdd and Pcb
|
||||
| Author: | driver3 [ October 7th, 2011, 4:40 ] | ||
| Post subject: | Re: Need pcb WD2500AAJS | ||
And the Pcb Component side chip is already soldered to another PCB but it does not work doner disk had a firm number that were different (Doner 60Z0A0) I have 60M0A1
|
|||
| Author: | northwind [ October 7th, 2011, 4:59 ] |
| Post subject: | Re: Need pcb WD2500AAJS |
We need a pic of the component side of the pcb. Unscrew the pcb, turn it over and take a pic. Then post pic here. |
|
| Author: | northwind [ October 7th, 2011, 5:01 ] |
| Post subject: | Re: Need pcb WD2500AAJS |
Ah ok i just saw you posted the right pic. I see there is a U12 chip on this board which needs to be transferred to the donor board in order for disk to identify correctly. I noticed, however, some markings on the plastic part of the pcb, as if someone was doing soldering job on this and the iron touched the plastic. Is this correct? And if so, what kind of repairs were done? |
|
| Author: | driver3 [ October 7th, 2011, 6:04 ] |
| Post subject: | Re: Need pcb WD2500AAJS |
yes that's right I had a doner pcbwith another firmware number so i soldering de U12 chip to the doner pcb .but it don’t work for me . The strange thing is the old PCB works in the doner disk with its own u12 but not vice versa. is it still the electronics |
|
| Author: | northwind [ October 7th, 2011, 10:34 ] |
| Post subject: | Re: Need pcb WD2500AAJS |
First, i can tell your soldering skills are below average. This is not bad, but you might have damaged the u12 chip and in that case things would be pretty bad. Secondly, what happens with the drive when you swapped u12 and put donor pcb to patient drive? Does it spin up or not? If not, assuming donor pcb is good, then u12 is either bad or soldering was wrong. Thirdly, what do you mean when you say that donor pcb "firmware" was different? Different pcb number? If you tried to put a donor pcb with different number to patient then this won't work. Lastly, i notice a TVS being hijacked on your picture (top right corner). What else did you do? |
|
| Author: | harddrivespecialist [ October 7th, 2011, 10:47 ] |
| Post subject: | Re: Need pcb WD2500AAJS |
If your PCB works on a donor drive, then you don't have a problem with PCB. Its internal problem. Can you describe original behavior? |
|
| Author: | driver3 [ October 7th, 2011, 10:56 ] |
| Post subject: | Re: Need pcb WD2500AAJS |
The picture of the board is the doner with my u12 chip which is 100% broken.i'm there alone so he set up my u12 is not lost. So in that corner just not pay attention. The PCB of the drive is good. drive spins up with this pcb (and his U12) only sees the pc him anymore soldered with hot air any way 
|
|
| Author: | driver3 [ October 8th, 2011, 2:31 ] |
| Post subject: | Re: Need pcb WD2500AAJS |
which numbers are important for the PCB ? I hear so many stories
|
|
| Author: | harddrivedonor [ November 13th, 2011, 7:37 ] |
| Post subject: | Re: Need pcb WD2500AAJS |
HELLO DRIVER3 we have it in stock: http://pcb-hdd.com/wd2500aajs-60moa1-20 ... -1028.html WD2500AAJS-60MOA1 2060-701590-001 REV A 484053-002 PCB DONOR |
|
| Page 1 of 1 | All times are UTC - 5 hours [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|